Deck 1: Designing Multi-Site HPE Storage Solutions

Question 1

A customer with an HPE 3PAR 8200 unit has concerns about tracking missing updates and where to find the information on when upgrades were done in the past. With previous storage systems the customer ran out of storage before knowing that they needed to order more storage. What can the integrator do to help the customer with these concerns?

A) Use the 3PAR Service Processor for Insplore event notification.
B) Enable StoreFront Remote integration.
C) Schedule SSMC Overview reports for the customer.
D) Link the 3PAR Service Agreement ID to customer`s HPE passport account for storage reporting.

Answer 1

Schedule SSMC Overview reports for the customer.

Question 2

A storage integrator has connected a new Windows Server 2008 R2 host to an HPE 3PAR StoreServ array. After creating a new 3PAR Virtual Volume and exporting it to the new host, the Disk Management tool on the host is displaying two new drives. Which additional software should the technician install to consolidate the displayed drive?

A) Storage Spaces
B) Enhanced Storage
C) File and Storage Services
D) Multipath I/O feature

Answer 2

Multipath I/O feature

Question 3

Refer to the exhibit. The administrator has presented an HPE 3PAR StoreServer virtual volume to a server. A single virtual volume is seen as two different offline disks on a Windows 2012 R2 server. What must be done to correct the issue?

A) Install HPE 3PAR DSM MPIO and reboot the server.
B) Install the latest HBA driver and reboot the server.
C) Install the MPIO feature and reboot the server.
D) Install 3PAR host explorer and start service.

Answer 3

Install HPE 3PAR DSM MPIO and reboot the server.

Question 4

Which management interface or tool primarily offers remote support capabilities for an HPE 3PAR StoreServ storage system?

A) HPE 3PAR Service Processor
B) HPE 3PAR Direct Connect
C) HPE Insight Remote Support
D) HPE Insight Online 3PAR

Question 5

Your customer has a requirement to provide identification information to the PDU such as server name, UUID number, and IP address from their ProLiant-based storage products. Which PDU do you recommend to meet this requirement?

A) HPE G2 Metered PDUs
B) HPE Intelligent PDU
C) HPE G2 Metered and Switched PDU
D) HPE Standard Series G2 Basic PDU

Question 6

Refer to the exhibit. A customer complains of poor performance on an HPE MSA 2040 storage array. The storage administrator thinks that the host ports could be limiting factor because only two ports are connected to the SAN fabric. To verify this the administrator wants to use the performance monitor of the MSA system, but has never used this monitor before. The administrator logs on to a HPE MSA 2040 in the lab to get familiar with performance monitoring. Which value would indicate a host port performance issue?

A) Read Response
B) IOPS
C) B/s
D) Queue Depth

Question 7

A storage integrator wants to change the tiering affinity of an existing volume on an HPE MSA 1040/2040 with GL220 and higher. How can this goal be achieved?

A) Change volume tier preference of the volume.
B) Migrate volume using new tiering settings.
C) Perform a clone operation with a new automatic tiering rule.
D) Delete the volume, and create a new volume with the correct automatic tiering rule.

Question 8

A storage integrator is validating an HPE 3PAR StoreServ implementation. The integrator created a volume in the HPE 3PAR StoreServ Management Console (SSMC) and needs to verify read/write access from a Linux operating system. Which steps are part of the verification process? (Choose two.)

A) Select Hosts under the Servers menu section, and click Create server.
B) Select the volume in the Virtual Volumes section. and click Map Volume in the Actions menu.
C) Select the host in the Servers section, and click Add permission in the Actions menu.
D) Select the volume in the Virtual Volumes section, and click Export in the Actions menu.
E) Select Hosts in the Block Persona menu section, and click Create host.

Question 9

Refer to the exhibit. A storage integrator is examining the configuration of an HPE 3PAR storage system using CLI. Which command can be used to display a list of common provisioning groups starting with substring R5 in the system?

A) showcpg R5*
B) cpg show | grep ^R5
C) cpg | grep R5*
D) cmore showcpg -I R5*

Question 10

A storage integrator is planning an HPE StoreVirtual VSA installation. Which network-related information may be needed for the implementation?

A) DHCP reservation for virtual IP address of the StoreVirtual cluster
B) jumbo frames need to be enabled for iSCSI traffic
C) flow-control needs to be disabled when using 10Gb NICs
D) virtual IP address for the StoreVirtual cluster

Question 11

A storage integrator has connected a new Windows Server 2012 host to a customer's fabric where five HPE 3PAR StoreServ arrays are already installed. The integrator plans to create a script to send the information about the new host to all HPE 3PAR arrays in an automated way. Which Host Explorer command should be used?

A) tpdhostget status
B) hostagent set
C) tpdhostagent push
D) hostagent list

Question 12

Refer to the exhibit. Which port can be used to connect the HPE MSA 2040 controller to hosts?

A) 4
B) 5
C) 6
D) 8

Question 13

A customer has HPE Data Protector and a StoreOnce VSA at a remote site that must replicate to the corporate data center StoreOnce backup device. What considerations must be taken into account to allow for Catalyst replication?

A) Data Protector Catalyst replication will rehydrate the data on the StoreOnce VSA then write to the data center StoreOnce.
B) Data Protector will write 2 backups: one to the StoreOnce VSA, the other to StoreOnce at the data center.
C) Data Protector Catalyst replication requires gateways to both sites to use Object copy.
D) Data Protector Catalyst replication is configured through the replication license on the StoreOnce VSA.

Question 14

A customer finds that the performance of their application is not optimal. The customer's application stores data on an HPE 3PAR StoreServ Array to a volume within an FC tier. How should the storage integrator move the application data to a volume within an SSD tier?

A) Backup the data, delete the FC volume, create a new SSD volume, and restore the data to it.
B) Use the Dynamic Optimization feature in the HPE 3PAR StoreServ Management Console.
C) Use the System Reporter feature in the HPE 3PAR StoreServ Management Console.
D) Create an SSD volume, use the server OS to copy the data to the new volume, and delete the FC volume.

Question 15

A customer currently utilizing HPE 3PAR StoreServ 7200 is experiencing performance bottlenecks within their SAN storage. Which cost-effective upsell or cross-sell HPE storage solution will offer significantly more performance and higher capacity to meet their needs and fit within their current infrastructure?

A) HPE 3PAR StoreServ File Controller v3 System
B) HPE 3PAR StoreServ 8440
C) 8-node HPE 3PAR StoreServ 20000 Storage
D) HPE StoreVirtual 3200 Storage

Question 16

An integrator is validating a design for an HPE 3PAR StoreServ solution. The assessment document shows that there is structured cabling between the rack the array will be installed in and the racks with the SAN switches. The fiber segments between the racks are documented as being 50 micron OM2 and are terminated with SC connectors. What needs to be considered when validating this design?

A) 3PAR arrays must be directly connected to SAN switches.
B) The SC connectors must be replaced by LC connectors.
C) OM2 Fiber cables are not supported for 8 Gbps.
D) Fiber segments cannot mix OM2 and OM4 cables.

Question 17

A system engineer installed HPE Insight Remote Support for an HPE MSA 2042 storage system at a customer's site. The engineer wants to integrate the system in HPE Insight Online to monitor it remotely. Which information does the engineer need from the customer to do the integration, using the Insight Remote Support GUI with HPE Insight Online? (Choose two.)

A) HPE Passport ID
B) Product number of MSA 2042
C) Service Agreement ID (SAID)
D) HPE Passport password
E) Serial number of MSA 2042

Question 18

A storage integrator has installed HPE OneView for vCenter to integrate HPE MSA 1040 management from a vSphere Web Client. Which typical configuration task is required after the installation of HPE OneView for vCenter?

A) license HPE OneView for VMware Storage Component
B) register HPE OneView for vCenter to Storage Management Utility
C) add HPE MSA Storage System to vCenter server
D) add vCenter server to HPE OneView for vCenter

Question 19

What must be configured before a storage integrator can start creating volumes from the available space on an HPE MSA 1040/2040?

A) disk group
B) snapshot space
C) date and time on MSA storage
D) global spare disk

Question 20

A storage integrator is installing the HPE StoreVirtual Centralized Management Console (CMC) to manage a StoreVirtual VSA cluster. What is the proper procedure to install the console?

A) Download the StoreVirtual CMC installer and start the installation from primary StoreVirtual VSA node.
B) Download the CMC Appliance and deploy to a hypervisor not running StoreVirtual VSA nodes.
C) Download the StoreVirtual CMC installer and run on the computer with a supported Linux operating system.
D) Download the CMC Appliance and deploy to hypervisors running StoreVirtual VSA nodes.

Question 21

A customer has requested the storage integrator to assist in installation of a HPE 3PAR StoreServ 8200. As a best practice, what should be taken into consideration when deploying 3PAR Virtual Service Processor?

A) Microsoft Hyper-V version of Virtual Service processor needs to be deployed to a CSV volume.
B) Installation of the Virtual Service processor is optional with a single two node HPE 3PAR StoreServ.
C) The Virtual Service processor should be deployed on other volume than a volume from the managed HPE 3PAR StoreServ.
D) Virtual Service processor for VMware vSphere should be installed using VMware Fault Tolerance.

Question 22

Refer to the exhibit. Which command can be used in the CLI console to set the static IP address and DNS server for an HPE StoreOnce device?

A) net set wizard
B) create network
C) setup network
D) run setup

Question 23

Refer to the exhibit. A customer wants to implement compression on an HPE 3PAR system and is concerned about potential bottlenecks on the CPU. Which CLI command can be used to display the CPU utilization and create a performance baseline?

A) perfcpu
B) cpustat
C) showcpu
D) statcpu

Question 24

Your customer needs to extend their storage SAN environment without the additional workload of manually creating zones for every new host or storage device. What will allow the customer to move from creating zones manually to having zones created automatically?

A) Brocade scripting of the zone setup
B) HPE 3PAR Smart SAN feature
C) break up of SAN switches to zone individually
D) HPE SAN Advisor

Question 25

An HPE StoreVirtual 3200 solution specifies 802.3ad (LACP) bonding is required for the network interfaces. What must be considered when implementing this solution?

A) Only one of the chosen network interfaces will actively pass traffic.
B) The network interfaces chosen may operate at the different speeds.
C) Additional switch configuration will be necessary.
D) The network interfaces chosen must be cabled to different switches.

Question 26

A customer wants to expand their SAN environment, which is based on B-series FC switches. They have a virtualized environment and two HPE 3PAR StoreServ arrays. Which tools can be used by the Integrator to check the health of the SAN environment before starting the expansion and after finishing? (Choose two.)

A) HPE SAN Network Advisor
B) HPE Complete AntemetA 3PAR Vision
C) Brocade SAN Health
D) HPE Enterprise Fabric Management Suite
E) HPE Central Management Console

Question 27

A storage integrator is installing an HPE MSA 2042 into a remote location as a part of warehouse automation solution. The site has no IT staff and warehouse employees will not be granted access to the location where the MSA will be installed. The customer is concerned about the inability to control individual AC power outlets connected to the MSA. Which HPE power delivery equipment can be added to the solution to address these requirements? (Choose two.)

A) HPE G2 Metered and Switched PDU
B) HPE Standard Series G2 Basic PDU
C) HPE iPDU
D) HPE G2 Metered PDU

Question 28

Refer to the exhibit. A storage integrator is deploying an HPE StoreOnce VSA. Which command can be used to find available storage capacity before it can be added in the StoreOnce console?

A) hardware setup storage
B) hardware run setup
C) hardware discover storage
D) hardware discover disks

Question 29

A storage integrator is planning the implementation of a single HPE StoreOnce 3100. How many power cords are required to be connected to PDU from this storage system, when power supply kit was ordered?

A) 0
B) 2
C) 4
D) 6

Question 30

A customer has an HPE 3PAR StoreServ 8000 system with three tiers of SSDs, SAS HDDs, and NL SAS. They are using Adaptive Flash Cache (AFC) and Adaptive Optimization (AO) across all three tiers. They want to implement a new virtual desktop infrastructure and want to use deduplication on the array for this workload. The integrator is in the process of implementing additional SSD drives to prepare the array for the new workload. What must the integrator do to implement this solution?

A) Disable AO to enable deduplication.
B) Disable AFC to enable deduplication.
C) Configure a new CPG for the SSD tier.
D) Create a new Virtual Domain.

Question 31

A customer has the following components installed and running: - HPE 3PAR StoreServ 8400 with two nodes - three SFF drive shelves - FC-based host connections - a mixture of SSDs and SAS HDDs The task is to expand the solution with two nodes and another three SFF drive shelves, as well as SSDs and SAS HDDs. What must be checked at the customer site before beginning the installation?

A) if there is space for the additional three SFF drive shelves adjacent to the existing drive shelves
B) if there is space for the second node pair adjacent to the first node pair
C) if there is the required number of High Density Active Optical Cables to connect the two node pairs
D) if the license for enabling the second node pair is installed before starting the expansion

Question 32

A storage integrator is handing over an installed HPE StoreOnce solution to the customer and demonstrates the default usernames and passwords for the StoreOnce GUI. The storage administrator is interested in creating another local administrator account. How can the storage administrator create an administrator account?

A) Use the native user management feature in the operating system.
B) Use the Add User link in the User Management screen in the StoreOnce GUI.
C) Create the new account in Integrated Lights-Out (iLO) and synchronize the account to StoreOnce.
D) Use the LDAP Integration screen in the StoreOnce GUI.

Question 33

The system administrator created a volume on an HPE MSA 2042 storage solution. The storage administrator is complaining that the Storage Management Utility (SMU) displays allocated space, but there is no data on the disk yet and the volume is empty. How can the storage integrator fix the issue?

A) Modify the volume and enable thin provisioning.
B) Create a virtual disk group and new virtual volume.
C) Modify the volume and convert it to virtual.
D) Create a linear disk group and new linear volume.

Question 34

A storage integrator is implementing an HPE 3PAR StoreServ system and connecting several storage volumes to a customer's VMware farm. During the implementation, the customer reveals that their legacy backup solution for protecting virtual machines does not provide a satisfactory RTO (recovery time objective). A recent implementation of new StoreOnce appliances did not fully solve the problem. Which HPE solution could the integrator demonstrate to address the customers RTO concerns?

A) HPE 3PAR StoreServ Management Console
B) HPE Complete iTernity iCAS
C) HPE 3PAR Integrated Management Console
D) HPE Recovery Manager Central for VMware

Question 35

After installing the HPE StoreOnce VSA into the VM environment, where can the version number of the software be checked?

A) in the install log file
B) on the console login screen
C) in the install messages
D) on the VMware vCenter

Question 36

What does DWPD (drive writes per day) for an SSD indicate?

A) the maximum number of 4K host writes to the entire drive capacity of the SSD per day over a three-year period
B) the maximum number of erase operations to the entire drive capacity of the SSD per day over a three-year period
C) the maximum number of 4K host writes to the entire drive capacity of the SSD per day over a five-year period
D) the maximum number of drive rewrite cycles (erase and write) for the SSD over a five-year period

Question 37

A storage integrator is handing over an installed HPE 3PAR storage system to a customer. The customer wants the original license key of the system for setlicense command that is used to prevent the system from prompting for confirmation of new license key. Which of the following command shows original license key?

A) showlicense -raw
B) displaylicense
C) licshow
D) licenseshow

Question 38

A storage integrator is handing over an installed HPE StoreOnce solution to the customer and demonstrates that the system is property configured. Which CLI command can be used to run an appliance self-test?

A) run confidencereport
B) run confidencereport all
C) system confidencechecker runtest all
D) confidencecheck

Question 39

A storage administrator has deployed a Windows 2012 R2 server which needs to have a virtual volume exported from an HPE StoreServ 8200. After zoning the host to storage and installing the HPE 3PAR Host Explorer on the server, the administrator is not seeing the server name in SSMC host list when creating a host object. What are two valid options to correct the issue? (Choose two.)

A) Enable host explorer discovery from the HPE 3PAR CLI.
B) Execute tpdhostagent push.
C) Restart the Host Explorer service.
D) Reinstall the Host Explorer service.
E) Restart the SSMC service.

Question 40

In which areas in SSMC can a 3PAR virtual domain membership be selected? (Choose two.)

A) iSCSI port
B) Host
C) Fibre Channel port
D) StoreServ report
E) Common Provisioning Group

Question 41

As a best practice, what should the Integrator do after finishing a storage solution installation?

A) Remove and insert each hot swappable component one-by-one.
B) Verify the used space in a rack.
C) Test storage solution functionality under the operational temperature range.
D) Verify the event logs are accumulating data.

Question 42

Where does HPE 3PAR StoreServ Data-at-Rest Encryption occur?

A) ASIC
B) physical disk
C) processor
D) host

Question 43

Refer to the exhibit. A storage integrator is planning to map an HPE StoreServ virtual volume to a server. Which tool can be used to gather required information, such as WWNs of the server, for exporting the volume?

A) HPE 3PAR PowerShell cmdlets
B) HPE 3PAR Host Explorer
C) HPE 3PAR CLI
D) Multipath I/O parameters

Question 44

A customer wants to back up their VMware data stores using consistent snapshots for rapid online recovery. Which RMC components are required when installing the solution?

A) HPE 3PAR StoreServ Array, RMC, RMC-V plugin
B) RMC-V plugin installed on the HPE 3PAR StoreServ Array
C) RMC virtual host, two HPE 3PAR StoreServ Arrays
D) RMC-V plugin installed on all ESX protected hosts

Question 45

A storage integrator is planning an HPE MSA Storage installation. What needs to be taken into consideration when implementing a SAS connected model?

A) SAS expander or a SAS switch is supported only with non-redundant paths.
B) SAS expander or a SAS switch is required if eight or more servers are connected.
C) Up to four servers with redundant paths can be connected.
D) Up to four servers with non-redundant paths can be connected.

Question 46

Which command can be used to display license information on an HPE StoreOnce system?

A) license show
B) info license
C) license display
D) show licenses

Question 47

What factors does a storage integrator need to consider before implementing an Ethernet-based SAN?

A) Data Center Bridging requires supported switches and NICs.
B) Remote Direct Memory Access (RDMA) support is mandatory for all components.
C) Data Center Bridging requires optical fiber cables.
D) Remote Direct Memory Access (RDMA) requires optical fiber cables.

Question 48

When is write throttling of HDDs invoked?

A) to synchronize speed of writing to multiple solid-state drives combined with rotational drives
B) to synchronize speed of writing to multiple solid-state drives
C) when drive wearing rate will cause the drive to fail before the warrantied time
D) when the power consumption of a drive exceeds the power cap

Question 49

A customer has a large deployment of HPE Synergy compute modules, HPE 3PAR StoreServ storage, and HPE StoreOnce systems in a single data center. They are concerned about the risk of data loss due to site disaster. What is the reason to propose HPE CloudBank?

A) To easily move workloads to AWS or Azure in the event of site disaster.
B) To improve RPO/RTO objectives by automating snapshot-based integrating between 3PAR and StoreOnce.
C) To regularly send backups to the cloud for the purposes of DR protection.
D) To leverage 3PAR snapshots and utilize StoreOnce recovery capabilities to minimize data loss and downtime.

Question 50

Refer to the exhibit. A customer is complaining about slow performance for their HPE 3PAR StoreServ system. Which CLI command can be used by the storage administrator to display the queue length of a VLUN attached to the server during the troubleshooting process?

A) perfvluns
B) statvirtvolmapping
C) show mappingsvirtvol
D) srstatvlun

Question 51

An HPE MSA 2042 supports three different types of drives. What is the best practice when enabling storage tiering?

A) Configure affinity per virtual volume and schedule optimization times.
B) Create three storage pools; assign performance and standard tiers to controller A and assign archive tier to controller B.
C) Configure affinity per storage pool, and set up virtual volume for tiering enabled.
D) Create three storage pools, assign them to same controller, and define affinity at a Virtual Volume level.

Question 52

The storage integrator is about to add new HPE 3PAR StoreServ 8200 to a customer's existing SAN infrastructure. What must be taken into account when developing a technical action plan?

A) customer change control procedures
B) action plan audience
C) environmental requirements
D) level of support

Question 53

An HPE StoreVirtual 3200 system consists of 19x 1.2 TB Drives in a RAID5 with a capacity level of 75%. The network is built with four HPE FlexFabric 5900 switches. The customer complained about performance challenges with the given configuration, and the administrator identified the drive configuration as a bottleneck. A performance analysis shows latencies above 60ms. Installation of the systems was done by best practices. Which actions should be performed to solve these issues? (Choose two.)

A) Advise additional tiering licenses.
B) Change RAID set to RAID 1 on both systems.
C) Offer SSD drives for tiering purposes and a performance boost.
D) Verify that a minimum of 4 RAID sets are built for optimal performance.
E) Set the bonding policy to ALB on both systems.

Question 54

A storage integrator is creating a domain in the 3PAR StoreServ Management Console (SSMC). Which settings of a 3PAR virtual domain have to be configured? (Choose two.)

A) Name
B) OpenLDAP server
C) Active Directory Domain Controller
D) Storage Controller
E) Storage System

Question 55

You need to add SSD drives to a production HPE 3PAR StoreServ array configured with Adaptive Flash Cache (AFC). What do you need to consider?

A) Online expansion is not supported if the AFC is running in simulation mode.
B) System performance might be affected during activation of the additional resources for AFC.
C) The system will automatically re-balance to use the additional resources for AFC.
D) The RAID configuration for the SSD drives might need adjustment if you want to use them for AFC.

Question 56

A storage integrator installed an HPE 3PAR StoreServ system. For which default accounts will the storage integrator need to hand over changed passwords to the customer?

A) 3parcust. 3paradm
B) cpmaint, spmaint
C) root, 3paradm
D) root, console

Question 57

Which resource provides configurations for HPE tested and referenced configurations in a software-defined storage environment?

A) HPE Storage Sizer
B) One Config Advanced
C) NinjaStars
D) StoreVirtual VSA Ready Nodes

Question 58

A customer is concerned about media and transmission errors caused by any component in the I/O stack from the server host bus adapter (HBA) into the HPE 3PAR StoreServ ports. Which feature will address the customer's concern?

A) Persistent Checksum
B) Persistent Cache
C) Peer Persistence
D) Persistent Ports

Question 59

When installing an HPE StoreOnce multimode system, which licenses must be available on all couplets to do Catalyst stores and to be allowed to do Catalyst replication?

A) Catalyst required for the first couplet
B) Catalyst and Replication licenses on the first couplet
C) Catalyst licenses on all couplets
D) Replication license on all couplets

Question 60

A customer needs to implement a new SAN fabric for their growing environment. The new SAN should provide a high performance and port-efficient network with many-to-many connectivity. Because of changing requirements and the possible acquisition of another company in the near feature, the customer cannot predict the I/O traffic pattern within the SAN. The customer is also concerned about availability. Which type of SAN topology should you recommend?

A) cascaded fabric
B) meshed fabric
C) core-edge fabric
D) single-switch fabric

Question 61

Which value does a Nimble solution provide in addition to other HPE storage solutions?

A) Flat support pricing for all hardware components
B) Future-proofed for newer technologies
C) All-inclusive software licensing over 5 years and additional capacity upgrades
D) Upfront option for free controller upgrade after 3 years

Question 62

During a technology workshop, the customer asks about differences between converged and Fibre Channel switches. What would be a benefit of using FlexFabric switches in a fibre channel storage environment?

A) support for six Ethernet and two Fibre Channel, or six Ethernet and two iSCSI or eight Ethernet adapters per server
B) zones can be configured for QoS with high, medium, and low priorities within a fabric on a zone by zone basis
C) in-flight compression and encryption provides efficient link utilization and security
D) support for combining multiple physical switches into one virtual switch with a single IP address

Question 63

A customer asks for a 50 TB disk-based backup solution with deduplication. They also need additional storage for test/dev purposes. Which single HPE storage platform can you present to the customer that will meet both of their needs?

A) HPE Nimble SF series
B) HPE StoreEasy Gateway
C) HPE StoreOnce
D) HPE Nimble CS series

Question 64

What is the benefit of HPE Synergy? (Choose two.)

A) It supports up to three HPE StoreVirtual VSA nodes for storage RAID.
B) It can compose and reclaim DAS storage.
C) It supports HPE BladeSystem c-class FlexFabric interconnect modules.
D) It can use HPE 3PAR File Persona for object storage.
E) It can prevent block storage services from HPE 3PAR as part of the resource pool.

Question 65

A customer is evaluating an HPE 3PAR StoreServ system in a proof-of-concept project. The customer wants to receive emails about important storage system events and alerts. What feature do you need to configure?

A) HPE OneView integration
B) Secure Service Agent
C) Real-time Alert Processing
D) Local Notification Service

Question 66

An HPE 3PAR StoreServ 9000 All-Flesh Array customer plans to deploy a secondary array 20 km away from their primary array to enable storage replication over a dark fibre. Their existing environment consists of one HPE Synergy Frame 12000, HPE SN6000B Fibre Channel Switches, HPE FlexFabric 5700 Switch Series, and HPE StoreOnce Systems. Which HPE license is required to meet the customer's technical requirements?

A) Intelligent Resilient Framework licenses
B) HPE StoreOnce Replication
C) Extended Fabric
D) HPE 3PAR Remote Copy

Question 67

A customer needs a backup solution for their virtualized environment. The backup solution must be agentless, hypervisor independent, and integrated with HPE storage solutions. The solution must support Nimble snapshot and replication management. Which product meets the customer requirements?

A) Veeam Backup and Replication
B) CommVault Simpana IntelliSnap
C) HPE StoreOnce Recovery Manager Central
D) Micro Focus Data Protector

Question 68

You are presenting the HPE StoreEver portfolio to a media agency. What advantage is offered when using LTFS?

A) file management capabilities will be provided with tape cartridges
B) WORM functionality for file, block and object storage access on tape
C) file encryption with public and private key management
D) file and block data management within an HPE HSM solution

Question 69

Which statement describes HPE StoreVirtual Network RAID functionality?

A) Redundancy is managed on a per-volume basis.
B) With Network RAID 10+2 data is striped and mirrored across two or more storage systems.
C) Network RAID 10 requires an even number of storage nodes.
D) Volumes remain available if an odd number of nodes are available.

Question 70

Which statement is correct when discussing the RAID layout of an HPE Nimble CS3000 storage system?

A) RAID 6 triple parity is set up -21 data drives are used for RAID stripes.
B) RAID 6 triple parity is set up -18 data drives are used for RAID stripes.
C) RAID 6 or RAID 1 can be set up -24 data drives are used for RAID stripes.
D) RAID 6 or RAID 1 can be set up -18 data drives are used for RAID stripes.

Question 71

How does the HPE StoreVirtual VSA storage platform scale performance and capacity?

A) eliminates the need for storage controllers
B) enables access through multiple protocols
C) aggregates all resources into a single storage pool
D) recreates storage pools on multiple devices

Question 72

A customer is concerned about the business risks of non-compliance for long-term data protection, retention, immutability, and encryption on petabytes of data consisting of millions of objects in a global namespace across multiple geographic locations. Which products should you recommend to the customer to address their concern? (Choose two.)

A) HPE StoreOnce Systems
B) HPE Complete Veeam
C) HPE Complete iTernity iCAS
D) HPE Scality RING on HPE Apollo Servers
E) HPE 3PAR StoreServ 9000

Question 73

Users are complaining about poor performance with their Data Warehouse application. What is an effective solution to increase their performance at minimal cost?

A) HPE 3PAR Adaptive Flash Cache
B) HPE 3PAR Priority Optimization
C) HPE 3PAR Dynamic Optimization
D) HPE 3PAR Adaptive Optimization

Question 74

You have just completed a performance analysis of an HPE 3PAR StoreServ 8400 disk array with different tiers at a customer's site. After reviewing the performance metrics, you determine that they should install a new tier of SSD drives. Which actions should you recommend they take to fully optimize the array? (Choose two.)

A) Configure Adaptive Flash Cache.
B) Configure scheduled tunesys tasks.
C) Rebalance all flash drives between nodes 0 and 2.
D) Configure Adaptive Optimization.
E) Configure dedicated drives to enable Adaptive Flash Cache.

Question 75

A customer has an HPE 3PAR StoreServ 8200 with eight 3.84 TB SSD's configured with RAID5 7+1. They plan to add four more 3.84 TB SSD's. What needs to be changed on the configuration once the new SSD's are installed?

A) Reconfigure the cpg setsize as RAID6 6+2 and wait for tunesys to complete.
B) Change the availability level from cage to magazine.
C) Adjust the cpg growth value to match amount of SSD's.
D) Change the cpg setsize to RAID5 5+1 and run tunesys.

Question 76

An HPE 3PAR StoreServ customer with FC, SSD and NL, drives is facing extreme latency during peak business hours with an OLTP application. They have enabled tiering using all drive types. What could be used to resolve the issue?

A) Dynamic Optimization using tier 2
B) Adaptive Optimization using tier 1
C) Dynamic Optimization between tier 0 and tier 1
D) Dynamic Optimization using tier 1

Question 77

A customer wants to expand his cascaded B-series based SAN but is concerned about latencies within the SAN backend. You recommend changing the topology to a full mesh. Which switch feature will ensure that the latencies in the backend are at the lowest possible level?

A) LACP
B) NPIV
C) FSPF
D) VSF

Question 78

A customer currently has a CS1000H and wants to upgrade to a CS3000. What must be considered before upgrading?

A) This upgrade is disruptive and needs planned downtime.
B) A capacity upgrade to a fully populated array has to be performed first.
C) Timeless storage support is not offered for SC1000H entry-level systems.
D) A controller upgrade to a CS1000F has to be performed first.

Question 79

A customer has mission-critical applications that intermittently experience heavy disk I/O. The storage speed has the most impact on the application's performance. The customer does not want to dedicate SSD disks to these applications because additional performance is only needed periodically, and moving the volumes between tiers takes too long. Which HPE StoreVirtual VSA feature can address this customer's challenge?

A) Storage virtualization
B) Space Reclamation
C) Thin Provisioning
D) Adaptive Optimization

Question 80

A customer is interested in integrating their HPE 3PAR StoreServ arrays into their OneView environment to support automated volume provisioning. What must you install to enable the integration?

A) HPE SAN Network Advisor Enterprise
B) HPE SAN Network Advisor Professional
C) 3PAR Host Explorer
D) OneView Global Dashboard