Deck 19: Transmission Reinstallation

Question 1

All of the following statements are true with respect to reinstalling the transmission except:

A) wear safety glasses.
B) check the lift placement.
C) never move the transmission by yourself.
D) the transmission should not be tilted or rotated while being installed.

Answer 1

D

Question 2

The flexplate holes are not evenly spaced. This helps in:

A) balancing the weight of the transmission.
B) preventing the flexplate from being installed in the wrong position.
C) preventing leakage.
D) preventing the bolts from loosening in service.

Answer 2

B

Question 3

Tech A states that flexplates can be installed in any direction. Tech B states that flexplate bolts need to be tightened with an impact gun to prevent the engine from spinning. Who is correct?

A) Tech A
B) Tech B
C) Both A and B
D) Neither A nor B

Answer 3

D

Question 4

When installing a torque converter, you should feel it catch and go in three times. The first engagement is with the:

A) stator.
B) turbine.
C) pump drive.
D) reinforcement plate.

Question 5

When installing a transmission in a front-wheel drive:

A) use the bolts to pull the transmission into place on the engine.
B) with the transmission seated against the engine, tighten the bolts as and when they are installed.
C) install the half shafts before removing the engine support bar.
D) lubricate the circlip with a small amount of transmission assembly lubricant or petroleum jelly.

Question 6

What precaution could be taken when reinstalling a half shaft if your area uses excessive amounts of road salt in the winter?

A) Apply petroleum jelly to the outer layer of the half shaft
B) Apply a thick coating of enamel paint to the outer surface of the half shaft
C) Apply a small amount of grease or anti-seize to the outer splines of the half shaft
D) Fix an outer plastic covering to prevent contact with the salt

Question 7

Using an impact gun to tighten up the axle retaining nut will:

A) ensure proper fit.
B) cause the bearing to have too much preload.
C) ensure that torque of the correct specification is applied.
D) prevent the axle from spinning while you torque the nut.

Question 8

Tech A states that the torque converter should be prefilled with transmission fluid. Tech B states that many new technicians struggle with installing a torque converter properly. Who is correct?

A) Tech A
B) Tech B
C) Both A and B
D) Neither A nor B

Question 9

Tech A states that by having an assistant step on the brake pedal, the axle nut can easily be torqued. Tech B states that half shafts need to be pushed into the transmission with a dead blow hammer. Who is correct?

A) Tech A
B) Tech B
C) Both A and B
D) Neither A nor B

Question 10

Tech A states that the transmission range switch should be adjusted before starting the vehicle after the transmission reinstallation. Tech B states that if the range switch is not adjusted the vehicle may not start. Who is correct?

A) Tech A
B) Tech B
C) Both A and B
D) Neither A nor B

Question 11

Tech A states that transmission electrical connectors should be filled with RTV to prevent water from getting into the contacts. Tech B states that the seals on electrical connectors should be checked for damage and replaced if they are damaged. Who is correct?

A) Tech A
B) Tech B
C) Both A and B
D) Neither A nor B

Question 12

Tech A states that the gasket between the transmission and transfer case should be replaced when reinstalling the transmission. Tech B states that you should bolt the torque converter to the flexplate before installing the torque converter into the transmission. Who is correct?

A) Tech A
B) Tech B
C) Both A and B
D) Neither A nor B

Question 13

After the transmission is installed properly into the vehicle, approximately what percentage of the total transmission fluid should be added to the transmission?

A) 100%
B) 50%
C) 75%
D) 25%

Question 14

Choose the correct statement with respect to transmission final checks.

A) Many transmissions will require the transmission fluid to be cold before the final check of fluid can be made.
B) Do not clear any transmission codes that are in the PCM.
C) The fluid level should be checked only after the test drive.
D) The longer test drive should run the transmission
through all of the gears.

Question 15

Tech A states that the transmission adaptives should be reset after you test drive the vehicle. Tech B states that the fluid level should be double checked after the initial test drive. Who is correct?

A) Tech A
B) Tech B
C) Both A and B
D) Neither A nor B

Question 16

Tech A states that on many new vehicles the PCM/TCM needs to be reflashed after rebuilding the transmission. Tech B states that many manufacturers will release updated software for PCM/TCMs after a vehicle has been manufactured. Who is correct?

A) Tech A
B) Tech B
C) Both A and B
D) Neither A nor B

Question 17

Transmission coolers can be cleaned by:

A) an aerosol flushing kit.
B) compressed air.
C) detergents.
D) rust inhibitors.

Question 18

A transmission fluid cooler that is leaking could cause all of the following except:

A) contamination of the transmission fluid.
B) plugging-up of transmission lines.
C) contamination of antifreeze.
D) freezing of the transmission fluid.

Question 19

Tech A states that transmission coolers must be replaced when replacing or rebuilding the transmission. Tech B states that the transmission cooler must be flushed to clear out debris before installing the new/rebuilt transmission. Who is correct?

A) Tech A
B) Tech B
C) Both A and B
D) Neither A nor B

Question 20

Tech A states that you should use the transmission bolts to pull the transmission into the engine. Tech B states that the transmission should slide over the dowel pins and against the engine easily. Who is correct?

A) Tech A
B) Tech B
C) Both A and B
D) Neither A nor B

Question 21

The technician should add fluid to the transmission until it reaches which point dipstick when performing the final checks to an automatic transmission.

A) Safe mark or full mark
B) Add mark or safe mark
C) Full or over-full mark
D) Until it is visible at any point on the dipstick

Question 22

If required, make sure to look up any procedures for resetting the adaptive memory after an automatic transmission rebuild so the Powertrain Control Module will reprogram its shift timing and pressures for the newly rebuilt transmission.

Question 23

After the installation of a newly rebuilt automatic transmission, the technician should double-check that all of the transmission's adjustments are correct, and then test-drive the vehicle to confirm normal operation of the rebuilt transmission.

Question 24

Always verify the manufacturer's service information for any software updates before installing the transmission.

Question 25

Technician A says that with the vehicle on the ground, install all of the required amount of transmission fluid before starting the vehicle. Technician B says to add 75% of the required transmission fluid, then start the vehicle and put shifter into each gear before rechecking the fluid level. Who is correct?

A) Technician A
B) Technician B
C) Both technicians
D) Neither technician

Question 26

Always check the transmission fluid at the required temperature.

Question 27

Technician A says that after an initial test drive, the fluid level should be re-inspected. Technician B says that after the initial test drive, the vehicle and transmission should be re-inspected for leaks and all fasteners should be retorqued. Who is correct?

A) Technician A
B) Technician B
C) Both technicians
D) Neither technician

Question 28

If the battery was disconnected, the adaptive memory may need to be reset.

Question 29

Technician A says that before test driving a recently rebuilt transmission, all DTCs should be erased. Technician B says that any cable adjustments should be verified before test driving. Who is correct?

A) Technician A
B) Technician B
C) Both technicians
D) Neither technician

Question 30

It is a good practice to have a customer return in a few hundred miles for a reinspection.

Question 31

An automatic transmission's torque converter that is not properly installed will cause catastrophic damage to the front pump when the vehicle is first started.

Question 32

It is not necessary to get the torque converter fully seated when installing it into the transmission.

Question 33

Technician A says when installing the torque converter, make sure all three components, oil pump drive, stator support, and turbine input shaft, engage with their mating parts. Technician B says after rebuilding the transmission and installing it into the vehicle, it is not necessary to take a test drive or recheck the fluid level. Who is correct?

A) Technician A
B) Technician B
C) Both A and B
D) Neither A nor B

Question 34

Proper removal and installation of an automatic transmission are just as critical as following the proper rebuilding techniques and practices for that transmission.

Question 35

Poor workmanship during the removal and installation of an automatic transmission can result in new transmission problems and reflect poorly on the reputation of the repair shop.

Question 36

Technician A says when installing the torque converter, make sure all three components, oil pump drive, stator support, and turbine input shaft, engage with their mating parts. Technician B says when installing the torque converter, if the torque converter bolts line up with the flex plate holes, you can be sure that it is installed into the transmission properly. Who is correct?

A) Technician A
B) Technician B
C) Both A and B
D) Neither A nor B

Question 37

All of the following statements are true with respect to the bolts and nuts securing the torque converter to the flex plate EXCEPT:

A) All of the engine's power pulses and torque are transmitted through three or four bolts to the torque converter.
B) If any bolts are found to be damaged, replace only the damaged bolts.
C) If the converter uses nuts, inspect the threads of the studs on the converter for thread damage
D) If the studs are damaged, the converter will need to be replaced.

Question 38

When the automatic transmission is removed from the vehicle, which of the following needs to be checked on the flex plate?

A) Crankshaft bolt holes for elongation and mounting area cracking
B) Torque converter bolt holes for elongation and mounting area cracking
C) Ring gear teeth for damage and flex plate body for cracking
D) All of the above

Question 39

Technician A says that a damaged flex plate can cause knocking noises and damage to the front pump of the transmission. Technician B says that all of the engine power pulses and torque are transmitted through the bolts or studs holding the automatic transmission's torque converter to the flex plate. Who is correct?

A) Technician A
B) Technician B
C) Both A and B
D) Neither A nor B

Question 40

If the transmission's torque converter bolts will be reused, the technician should check the threads carefully for damage and wear.

Question 41

Which of these is not a common fault found when inspecting a flex plate?

A) Cracks
B) Elongation of bolt holes
C) Starter ring gear damage
D) Discoloration from heat

Question 42

Which of the following is least likely to be a fault found when inspecting a flexplate and flexplate mounting area?

A) Cracks
B) Elongation of bolt holes
C) Starter ring gear damage
D) Heat discoloring

Question 43

Technician A says that the torque converter should be bolted to the flex plate before installing the transmission. Technician B says that when installing the torque converter, three separate engagements with their mating parts must be felt. Who is correct?

A) Technician A
B) Technician B
C) Both A and B
D) Neither A nor B

Question 44

Technician A says that when inspecting the torque converter, you need to check the snout of the converter where the seal and bushing rides for excessive wear. Technician B says that the internal end play of the converter must be checked. Who is correct?

A) Technician A
B) Technician B
C) Both A and B
D) Neither A nor B

Question 45

Which of the following should be inspected before reinstalling the transmission?

A) The rear main oil seal
B) The engine core plugs
C) The engine dowel pins
D) All of the above

Question 46

The transmission cooler should always be cleaned before installing a new or rebuilt transmission.

Question 47

The aerosol can transmission cooler cleaning canister is usually good for three or four coolers before it needs replacing.

Question 48

What can a leaking automatic transmission fluid cooler cause?

A) A transmission to fail from a low fluid level
B) Antifreeze to be drawn into the cooler from the radiator, contaminating the transmission fluid
C) Transmission fluid to leak into the radiator contaminating the antifreeze
D) All of the above

Question 49

Blocked transmission coolers can starve which of the following transmission circuits?

A) Torque converter clutch circuit
B) Throttle pressure circuit
C) Governer pressure circuit
D) Transmission lubrication circuit

Question 50

Technician A says it is critical to clean and inspect the transmission fluid cooler and lines. Technician B says metal particles and clutch material can become stuck inside the fluid cooler or fluid cooler lines. Who is correct?

A) Technician A
B) Technician B
C) Both A and B
D) Neither A nor B

Question 51

Technician A says you can clean a transmission cooler and lines using the shop's parts cleaning tank. Technician B says you can clean a transmission cooler and lines with an aerosol flushing kit. Who is correct?

A) Technician A
B) Technician B
C) Both A and B
D) Neither A nor B

Question 52

Technician A says when replacing an automatic transmission, it is critical to clean and inspect the transmission fluid cooler and lines. Technician B says metal particles and clutch material can become stuck inside the fluid cooler or fluid cooler lines. Who is correct?

A) Technician A
B) Technician B
C) Both A and B
D) Neither A nor B

Question 53

Technician A says you can clean a transmission cooler and lines using the shop's parts cleaning tank. Technician B says you can clean a transmission cooler and lines with an aerosol flushing kit. Who is correct?

A) Technician A
B) Technician B
C) Both A and B
D) Neither A nor B

Question 54

Before installing a new or rebuilt transmission, which of the following must be carefully cleaned and inspected?

A) Transmission oil cooler.
B) Rear differential .
C) Transfer case mating surface.
D) None of the answers listed

Question 55

Technician A says that the cooler and cooler lines should be flushed as part of a transmission rebuild. Technician B says that if the cooler is not flushed oil returning from the cooler can carry debris into the torque converter, and cause damage to it. Who is correct?

A) Technician A
B) Technician B
C) Both A and B
D) Neither A nor B

Question 56

Tech A states that you should use the transmission bolts to pull the transmission into the engine. Tech B states that the transmission should slide over the dowel pins and against the engine easily. Who is correct?

A) Tech A
B) Tech B
C) Both A and B
D) Neither A nor B

Question 57

Transmission coolers can be cleaned by:

A) an aerosol flushing kit.
B) compressed air.
C) detergents.
D) rust inhibitors.

Question 58

A transmission fluid cooler that is leaking could cause all of the following except:

A) contamination of the transmission fluid.
B) plugging-up of transmission lines.
C) contamination of antifreeze.
D) freezing of the transmission fluid.

Question 59

Tech A states that transmission coolers must be replaced when replacing or rebuilding the transmission. Tech B states that the transmission cooler must be flushed to clear out debris before installing the new/rebuilt transmission. Who is correct?

A) Tech A
B) Tech B
C) Both A and B
D) Neither A nor B

Question 60

After the transmission is installed properly into the vehicle, approximately what percentage of the total transmission fluid should be added to the transmission?

A) 100%
B) 50%
C) 75%
D) 25%

Question 61

Choose the correct statement with respect to transmission final checks.

A) Many transmissions will require the transmission fluid to be cold before the final check of fluid can be made.
B) Do not clear any transmission codes that are in the PCM.
C) The fluid level should be checked only after the test drive.
D) The longer test drive should run the transmission
through all of the gears.

Question 62

Tech A states that the transmission adaptives should be reset after you test drive the vehicle. Tech B states that the fluid level should be double checked after the initial test drive. Who is correct?

A) Tech A
B) Tech B
C) Both A and B
D) Neither A nor B

Question 63

Tech A states that on many new vehicles the PCM/TCM needs to be reflashed after rebuilding the transmission. Tech B states that many manufacturers will release updated software for PCM/TCMs after a vehicle has been manufactured. Who is correct?

A) Tech A
B) Tech B
C) Both A and B
D) Neither A nor B

Question 64

When installing a torque converter, you should feel it catch and go in three times. The first engagement is with the:

A) stator.
B) turbine.
C) pump drive.
D) reinforcement plate.

Question 65

When installing a transmission in a front-wheel drive:

A) use the bolts to pull the transmission into place on the engine.
B) with the transmission seated against the engine, tighten the bolts as and when they are installed.
C) install the half shafts before removing the engine support bar.
D) lubricate the circlip with a small amount of transmission assembly lubricant or petroleum jelly.

Question 66

What precaution could be taken when reinstalling a half shaft if your area uses excessive amounts of road salt in the winter?

A) Apply petroleum jelly to the outer layer of the half shaft
B) Apply a thick coating of enamel paint to the outer surface of the half shaft
C) Apply a small amount of grease or anti-seize to the outer splines of the half shaft
D) Fix an outer plastic covering to prevent contact with the salt

Question 67

Using an impact gun to tighten up the axle retaining nut will:

A) ensure proper fit.
B) cause the bearing to have too much preload.
C) ensure that torque of the correct specification is applied.
D) prevent the axle from spinning while you torque the nut.

Question 68

Tech A states that the torque converter should be prefilled with transmission fluid. Tech B states that many new technicians struggle with installing a torque converter properly. Who is correct?

A) Tech A
B) Tech B
C) Both A and B
D) Neither A nor B

Question 69

Tech A states that by having an assistant step on the brake pedal, the axle nut can easily be torqued. Tech B states that half shafts need to be pushed into the transmission with a dead blow hammer. Who is correct?

A) Tech A
B) Tech B
C) Both A and B
D) Neither A nor B

Question 70

Tech A states that the transmission range switch should be adjusted before starting the vehicle after the transmission reinstallation. Tech B states that if the range switch is not adjusted the vehicle may not start. Who is correct?

A) Tech A
B) Tech B
C) Both A and B
D) Neither A nor B

Question 71

Tech A states that transmission electrical connectors should be filled with RTV to prevent water from getting into the contacts. Tech B states that the seals on electrical connectors should be checked for damage and replaced if they are damaged. Who is correct?

A) Tech A
B) Tech B
C) Both A and B
D) Neither A nor B

Question 72

Tech A states that the gasket between the transmission and transfer case should be replaced when reinstalling the transmission. Tech B states that you should bolt the torque converter to the flexplate before installing the torque converter into the transmission. Who is correct?

A) Tech A
B) Tech B
C) Both A and B
D) Neither A nor B

Question 73

All of the following statements are true with respect to reinstalling the transmission except:

A) wear safety glasses.
B) check the lift placement.
C) never move the transmission by yourself.
D) the transmission should not be tilted or rotated while being installed.

Question 74

The flexplate holes are not evenly spaced. This helps in:

A) balancing the weight of the transmission.
B) preventing the flexplate from being installed in the wrong position.
C) preventing leakage.
D) preventing the bolts from loosening in service.

Question 75

Tech A states that flexplates can be installed in any direction. Tech B states that flexplate bolts need to be tightened with an impact gun to prevent the engine from spinning. Who is correct?

A) Tech A
B) Tech B
C) Both A and B
D) Neither A nor B

Question 76

The technician should add fluid to the transmission until it reaches which point dipstick when performing the final checks to an automatic transmission.

A) Safe mark or full mark
B) Add mark or safe mark
C) Full or over-full mark
D) Until it is visible at any point on the dipstick

Question 77

What can a leaking automatic transmission fluid cooler cause?

A) A transmission to fail from a low fluid level
B) Antifreeze to be drawn into the cooler from the radiator, contaminating the transmission fluid
C) Transmission fluid to leak into the radiator contaminating the antifreeze
D) All of the above

Question 78

Blocked transmission coolers can starve which of the following transmission circuits?

A) Torque converter clutch circuit
B) Throttle pressure circuit
C) Governer pressure circuit
D) Transmission lubrication circuit

Question 79

Technician A says some vehicles are equipped with a dust cover that needs to be removed to access the bolts connecting the torque converter to the flywheel. Technician B says when removing a transmission, you do not need to disconnect the transmission cooler lines. Who is correct?

A) Technician A
B) Technician B
C) Both A and B
D) Neither A nor B

Question 80

Technician A says when installing the torque converter, make sure all three components, oil pump drive, stator support, and turbine input shaft, engage with their mating parts. Technician B says after rebuilding the transmission and installing it into the vehicle, it is not necessary to take a test drive or recheck the fluid level. Who is correct?

A) Technician A
B) Technician B
C) Both A and B
D) Neither A nor B