Deck 2: Care and Use of the Compound Light Microscope

Question 1

If a microscope is ________,then the user will not have to make adjustments to focus the specimen when switching between objective lenses.

A) compound
B) binocular
C) parfocal
D) monocular

Answer 1

C

Question 2

As the resolving power of the objective lens increases,the working distance ________.

A) increases
B) decreases
C) increases by a factor of 10
D) remains the same

Answer 2

B

Question 3

The ________ controls the brightness of the light emitted from the substage light source.

A) iris diaphragm
B) stage
C) mechanical stage
D) condenser lens

Answer 3

A

Question 4

The ability to distinguish close objects as separate and distinct is known as ________.

A) working distance
B) field of view
C) resolving power
D) depth of field

Question 5

The ________ is a revolving structure that holds the objective lenses.

A) coarse adjustment knob
B) nosepiece
C) mechanical stage control knobs
D) fine adjustment knob

Question 6

As the user switches to a higher-power lens to increase total magnification,the field of view ________.

A) decreases
B) decreases 4×
C) increases
D) remains the same

Question 7

At a total magnification of 100×,the diameter of the field of view is 6 mm.If the total magnification is increased to 1000×,the diameter of the field of view is ________.

A) 0.6 mm
B) 0.06 mm
C) 60 mm
D) 600 mm

Question 8

The proper way to carry a microscope is in front of your body with one hand gripping the ________ and the other hand supporting the ________.

A) arm; base
B) head; stage
C) objective lenses; base
D) ocular lenses; arm

Question 9

The coarse and fine adjustment knobs are used to ________.

A) nosepiece
B) make initial and subsequent focusing adjustments when viewing a specimen.
C) secure the specimen on the stage
D) illuminate the specimen

Question 10

All microscope lenses should be cleaned with ________.

A) lens paper
B) tissue paper
C) paper
D) paper towels

Question 11

If a student uses a parfocal compound light microscope,which of the following would be true?

A) The focus will have to be adjusted using the mechanical stage control knob.
B) After the initial focus adjustments are made, the image should remain in focus as the specimen is viewed with each objective lens.
C) The focus will have to be adjusted using the coarse adjustment knob.
D) The focus will have to be adjusted using the fine adjustment knob.

Question 12

If the microscope is not parfocal,the user should make focusing adjustments using the ________ adjustment knob when viewing a specimen under high power.

A) coarse
B) condenser
C) stage
D) fine

Question 13

The total magnification of a specimen can be calculated by multiplying the ocular lens magnification by the ________ lens magnification.

A) low power
B) scanning
C) high power
D) objective

Question 14

Assume a structure within a specimen fills approximately 25 percent of the diameter of the field of view.If the field diameter is known to be 3.5 mm,calculate the size of the structure.

A) 0.14 mm
B) 14 mm
C) 0.875 mm
D) 0.0875 mm

Question 15

As the coarse adjustment knob is turned,the stage (or in some cases the nosepiece)________.

A) remains stationary
B) moves forward or backward
C) moves up or down, depending on the direction that the knob is turned
D) moves left or right, depending on the direction that the knob is turned

Question 16

Calculate the total magnification of a specimen if the magnification of the ocular lens is 10× and the magnification of the objective lens is 45×.

A) 450×
B) 4.5×
C) 45×
D) 4500×

Question 17

The distance between the objective lens and the microscope stage is called the ________.

A) mechanical stage
B) working distance
C) resolving power
D) total magnification

Question 18

To avoid damaging a lens or breaking a slide,the user should always begin viewing a specimen with the ________ power objective lens.

A) medium
B) lowest
C) oil immersion
D) highest

Question 19

Inversion of image means that when viewing a specimen with a light microscope,the image that you see will be ________ and ________.

A) distorted; magnified
B) magnified; inverted
C) inverted; reversed
D) magnified; reversed

Question 20

The ________ lens is known as the oil immersion lens.

A) 4×
B) 10×
C) 40×
D) 100×