Chat with AIExam 15: Division of Decimals
Exam 1: Addition of Whole Numbers10 Questions
Exam 2: Subtraction of Whole Numbers10 Questions
Exam 3: Multiplication of Whole Numbers10 Questions
Exam 4: Division of Whole Numbers10 Questions
Exam 5: Introduction to Common Fractions10 Questions
Exam 6: Measuring Instruments: the Tape Measure, Caliper, and Micrometer9 Questions
Exam 7: Addition of Common Fractions10 Questions
Exam 8: Subtraction of Common Fractions10 Questions
Exam 9: Multiplication of Common Fractions10 Questions
Exam 10: Division of Common Fractions10 Questions
Exam 40: Economical Layouts of Rectangular Plates10 Questions
Exam 11: Combined Operations With Common Fractions10 Questions
Exam 13: Addition and Subtraction of Decimal Fractions10 Questions
Exam 14: Multiplication of Decimals10 Questions
Exam 15: Division of Decimals10 Questions
Exam 16: Decimal Fractions and Common Fraction Equivalents10 Questions
Exam 17: Tolerances10 Questions
Exam 18: Combined Operations With Decimal Fractions10 Questions
Exam 19: Equivalent Measurements10 Questions
Exam 20: Averages10 Questions
Exam 21: Percents and Percentages10 Questions
Exam 22: The Metric System of Measurements10 Questions
Exam 23: English-Metric Equivalent Unit Conversions10 Questions
Exam 24: Combined Operations With Equivalent Units10 Questions
Exam 25: Perimeter of Squares and Rectangles, Order of Operations10 Questions
Exam 26: Area of Squares and Rectangles10 Questions
Exam 27: Area of Triangles and Trapezoids10 Questions
Exam 28: Volume of Cubes and Rectangular Shapes10 Questions
Exam 29: Volume of Rectangular Containers10 Questions
Exam 30: Circumference of Circles, and Perimeter of Semicircular-Shaped Figures10 Questions
Exam 31: Area of Circular and Semicircular Figures10 Questions
Exam 32: Volume of Cylindrical Shapes10 Questions
Exam 33: Volume of Cylindrical and Complex Containers10 Questions
Exam 34: Mass Weight Measure10 Questions
Exam 35: Angle Development10 Questions
Exam 36: Angular Measurement10 Questions
Exam 38: Bends and Stretchouts of Angular Shapes10 Questions
Exam 39: Bends and Stretchouts of Circular and Semicircular Shapes10 Questions
Exam 41: Economic Layout of Odd-Shaped Pieces; Take-Off S10 Questions
Select questions type
What is 45.34 /5.1?.Round the answer to the nearest hundredths.
Free
(Short Answer)
4.8/5 
(40)
(40) Correct Answer:
Verified
Verified8.89
Figure 15-2 
-A welder cuts this plate into pieces that are 8.75" wide. How many whole pieces are cut? Disregard waste caused by the cuts.
-A welder cuts this plate into pieces that are 8.75" wide. How many whole pieces are cut? Disregard waste caused by the cuts.Free
(Short Answer)
4.8/5 (30)
(30) Correct Answer:Verified
Verified5
Figure 15-1 
-A welder saw cuts this length of steel angle into 3 equal pieces. What is the length of each piece? Disregard waste caused by the saw cuts. Round the answer to two decimal places.
-A welder saw cuts this length of steel angle into 3 equal pieces. What is the length of each piece? Disregard waste caused by the saw cuts. Round the answer to two decimal places. (Short Answer)
4.8/5 (40)
(40) Figure 15-3 
-A welder shears a 87.15" piece of key stock into pieces that are 3.25" long. How many whole pieces are sheared?
-A welder shears a 87.15" piece of key stock into pieces that are 3.25" long. How many whole pieces are sheared? (Short Answer)
4.7/5 (35)
(35) Figure 15-3
-A welder saws this square stock into five equal pieces. What is the length of each piece? Allow 1/16" waste for each cut. Round your answer to the nearest hundredth.
-A welder saws this square stock into five equal pieces. What is the length of each piece? Allow 1/16" waste for each cut. Round your answer to the nearest hundredth. (Short Answer)
4.7/5 (36)
(36) Figure 15-2
-A welder cuts this plate into pieces that are 7" wide. How many whole pieces are cut? Disregard waste caused by the cuts.
-A welder cuts this plate into pieces that are 7" wide. How many whole pieces are cut? Disregard waste caused by the cuts. (Short Answer)
4.9/5 (38)
(38) Figure 15-3
-A welder saws this square stock into seven equal pieces. What is the length of each piece? Allow 1/16" waste for each cut. Round your answer to the nearest hundredth.
-A welder saws this square stock into seven equal pieces. What is the length of each piece? Allow 1/16" waste for each cut. Round your answer to the nearest hundredth. (Short Answer)
4.9/5 (24)
(24) Figure 15-1
-A welder saw cuts this length of steel angle into 6 equal pieces. What is the length of each piece? Disregard waste caused by the saw cuts. Round the answer to two decimal places.
-A welder saw cuts this length of steel angle into 6 equal pieces. What is the length of each piece? Disregard waste caused by the saw cuts. Round the answer to two decimal places. (Short Answer)
4.8/5 (29)
(29) A MIG unit is using a spool of wire that weighs 24 pounds. How many hours will the spool last if the melt-off is 1.75 pounds/hour? Round the answer to the nearest hundredth.
(Short Answer)
4.7/5 (23)
(23) 
Filters
- Essay(0)
- Multiple Choice(0)
- Short Answer(0)
- True False(0)
- Matching(0)