Exam 58: Programmable and Motion Control
Exam 1: General Principles of Electric Motor Control10 Questions
Exam 2: Fractional and Integral Horsepower Manual Motor Starters10 Questions
Exam 3: Magnetic Starters10 Questions
Exam 4: Symbols10 Questions
Exam 5: Interpretation and Application of Simple Wiring and Elementary Diagrams10 Questions
Exam 6: Push Buttons and Control Stations10 Questions
Exam 7: Relays10 Questions
Exam 8: Contactors10 Questions
Exam 9: Timing Relays10 Questions
Exam 10: Pressure Switches and Regulators10 Questions
Exam 11: Float Switches10 Questions
Exam 12: Flow Switches10 Questions
Exam 13: Limit Switches and Proximity Control10 Questions
Exam 14: Phase Failure Relays9 Questions
Exam 15: Solenoid Valves10 Questions
Exam 16: Temperature Switches10 Questions
Exam 17: Two-Wire Controls9 Questions
Exam 18: Three-Wire and Separate Controls10 Questions
Exam 19: Hand-Off Automatic Controls8 Questions
Exam 20: Multiple Push-Button Stations8 Questions
Exam 21: Interlocking Methods for Reversing Control10 Questions
Exam 22: Sequence Control10 Questions
Exam 23: Jogging Inching Control Circuits10 Questions
Exam 24: Time-Delay Low-Voltage Release Relay10 Questions
Exam 25: The Motor and Starting Methods10 Questions
Exam 26: Primary Resistor-Type Starters10 Questions
Exam 27: Autotransformer Starters10 Questions
Exam 28: Part Winding Motor Starters10 Questions
Exam 29: Automatic Starters for Star-Delta Motors10 Questions
Exam 30: Ac Solid-State Reduced Voltage Controller10 Questions
Exam 31: Controllers for Two-Speed Two-Winding 28separate Winding29 Motors10 Questions
Exam 32: Two-Speed One-Winding 28consequent Pole29 Motor Controller10 Questions
Exam 33: Four-Speed Two-Winding 28consequent Pole29 Motor Controller10 Questions
Exam 34: Wound Rotor Motors and Manual Speed Control10 Questions
Exam 35: Push-Button Speed Selection8 Questions
Exam 36: Automatic Acceleration for Wound Rotor Motors10 Questions
Exam 37: Automatic Speed Control for Wound Rotor Motors8 Questions
Exam 38: Solid-State Adjustable Speed Controller for Ac Wound Rotor Motors10 Questions
Exam 39: Synchronous Motor Operation10 Questions
Exam 40: Push-Button Synchronizing10 Questions
Exam 41: Timed Semiautomatic Synchronizing4 Questions
Exam 42: Synchronous Automatic Motor Starter10 Questions
Exam 43: About Dc Motors10 Questions
Exam 44: Use of Reduced Voltage for Starting10 Questions
Exam 45: Across-The-Line Starting6 Questions
Exam 46: Compensating and Definite Time Control Starting10 Questions
Exam 47: Solid-State Adjustable Speed Control10 Questions
Exam 48: Plugging10 Questions
Exam 49: Electric Brakes10 Questions
Exam 50: Dynamic and Regenerative Braking10 Questions
Exam 51: Electric and Electronic Braking10 Questions
Exam 52: Direct Drives and Pulley Drives10 Questions
Exam 53: Gear Motors10 Questions
Exam 54: Variable-Frequency Mechanical Drives10 Questions
Exam 55: Ac Adjustable Frequency Drives10 Questions
Exam 56: Magnetic Clutch and Magnetic Drive10 Questions
Exam 57: Dc Variable-Speed Control 14motor Drives10 Questions
Exam 58: Programmable and Motion Control10 Questions
Exam 59: Motor Startup and Troubleshooting Basics10 Questions
Exam 60: Troubleshooting Techniques10 Questions
Select questions type
If you set your alarm clock or clock radio to wake your household in the morning, you have programmed a controller.
Free
(True/False)
4.9/5
(43)
Correct Answer:
True
Permanent magnet synchronous motors are AC motors that eliminate the slip characteristic of ______________motors.
Free
(Multiple Choice)
4.9/5
(33)
Correct Answer:
D
The self-synchronous transmission system is a system used for transmitting, by electrical means, any signal that can be represented by___________ .
Free
(Multiple Choice)
4.7/5
(32)
Correct Answer:
A
Some output modules are capable of switching starters through size 10.
(True/False)
4.9/5
(31)
A modern motor control center combines the latest automation technologies in a common _________________.
(Multiple Choice)
4.7/5
(34)
A synchro unit draws but little power from the line and is designed for_______________ .
(Multiple Choice)
4.9/5
(41)
Programming may be accomplished either at the processor site or remote to the processor.
(True/False)
4.9/5
(43)
If the solid-state output of a programmable controller is intended to control an AC voltage, the output control device will be a __________.
(Multiple Choice)
4.8/5
(29)
Filters
- Essay(0)
- Multiple Choice(0)
- Short Answer(0)
- True False(0)
- Matching(0)