Question 1

When dimensioning angles, you should extend curved extension lines and connect them with straight dimension lines.

Accepted Answer

A) True 
 B)False

Question 2

Which symbol is used to indicate the the lay is angular in both directions to the line representing the surface to which the symbol is applied?

Accepted Answer

A)  = 
B)  z 
C)  M 
D)  X 
A)  = 
B)  z 
C)  M 
D)  X

Question 3

U.S. customary dimensioning is based on _____ values.

Accepted Answer

A)  decimal-inch 
B)  fraction-inch 
C)  decimal-millimeter 
D)  fraction-millimeter 
A)  decimal-inch 
B)  fraction-inch 
C)  decimal-millimeter 
D)  fraction-millimeter

Question 4

Chamfers may be external, internal, or oblique.

Accepted Answer

A) True 
 B)False

Question 5

Fillets are inside rounded corners.

Accepted Answer

A) True 
 B)False

Question 6

Imagine that you need to record a dimension value of one-half millimeter. What is the correct way to record this value according to ASME standards?

Accepted Answer

A)  .5 mm 
B)  0.5 
C)  0.50 
D)  0.50 mm 
A)  .5 mm 
B)  0.5 
C)  0.50 
D)  0.50 mm

Question 7

Which term refers to outside rounded corners?

Accepted Answer

A)  chamfers 
B)  fillets 
C)  knurling 
D)  rounds 
A)  chamfers 
B)  fillets 
C)  knurling 
D)  rounds

Question 8

Leaders can be used to connect a specific area of a drawing to a dimension or note.

Accepted Answer

A) True 
 B)False

Question 9

Imagine that you need to record a dimension value of three-quarters of an inch or 19 millimeters. What is the correct way to record this dimension according to ASME standards for U.S. customary dimensioning?

Accepted Answer

A)  3/4 
B)  .75 
C)  0.75 
D)  19 
A)  3/4 
B)  .75 
C)  0.75 
D)  19

Question 10

Which statement about pictorial drawings is correct?

Accepted Answer

A)  They are commonly used as working drawings. 
B)  They are usually used without additional dimensioned drawings. 
C)  They are usually accompanied by a fully dimensioned multiview drawing. 
D)  They are usually accompanied by a fully dimensioned single-view drawing. 
A)  They are commonly used as working drawings. 
B)  They are usually used without additional dimensioned drawings. 
C)  They are usually accompanied by a fully dimensioned multiview drawing. 
D)  They are usually accompanied by a fully dimensioned single-view drawing.

When dimensioning angles, you should extend curved extension lines and connect them with straight dimension lines.

Which symbol is used to indicate the the lay is angular in both directions to the line representing the surface to which the symbol is applied?

U.S. customary dimensioning is based on _____ values.

Chamfers may be external, internal, or oblique.

Fillets are inside rounded corners.

Imagine that you need to record a dimension value of one-half millimeter. What is the correct way to record this value according to ASME standards?

Which term refers to outside rounded corners?

Leaders can be used to connect a specific area of a drawing to a dimension or note.

Imagine that you need to record a dimension value of three-quarters of an inch or 19 millimeters. What is the correct way to record this dimension according to ASME standards for U.S. customary dimensioning?

Which statement about pictorial drawings is correct?

Introduction to Contemporary Drafting

Drafting Equipment and Supplies

Sketching and Lettering

Introduction to Computer-Aided Drafting Systems

Drafting Room Design Teams

Drafting Conventions and Formats

Geometric Construction

Multiview Drawings

Tolerancing and Geometric Tolerancing

Sectional Views

Auxiliary Views and Revolutions

Descriptive Geometry

Development Drawings

Pictorial Drawings

Fasteners

Green Design in Industry

Working Drawings

Welding Drawings

Gears and Cams

Piping Drawings

Electronics Drafting

Tool Design Drafting

Architectural Drafting

Filters

Exam 9: Dimensioning Conventions and Surface Finishes

When dimensioning angles, you should extend curved extension lines and connect them with straight dimension lines.

Which symbol is used to indicate the the lay is angular in both directions to the line representing the surface to which the symbol is applied?

U.S. customary dimensioning is based on _____ values.

Chamfers may be external, internal, or oblique.

Fillets are inside rounded corners.

Imagine that you need to record a dimension value of one-half millimeter. What is the correct way to record this value according to ASME standards?

Which term refers to outside rounded corners?

Leaders can be used to connect a specific area of a drawing to a dimension or note.

Imagine that you need to record a dimension value of three-quarters of an inch or 19 millimeters. What is the correct way to record this dimension according to ASME standards for U.S. customary dimensioning?

Which statement about pictorial drawings is correct?

Introduction to Contemporary Drafting

Drafting Equipment and Supplies

Sketching and Lettering

Introduction to Computer-Aided Drafting Systems

Drafting Room Design Teams

Drafting Conventions and Formats

Geometric Construction

Multiview Drawings

Tolerancing and Geometric Tolerancing

Sectional Views

Auxiliary Views and Revolutions

Descriptive Geometry

Development Drawings

Pictorial Drawings

Fasteners

Green Design in Industry

Working Drawings

Welding Drawings

Gears and Cams

Piping Drawings

Electronics Drafting

Tool Design Drafting

Architectural Drafting

Filters