Chat with AIExam 8: Allowance for Threaded Fittings
Exam 1: Some Basic Rules for Mathematics7 Questions
Exam 2: Formulas8 Questions
Exam 3: Solving Formulas Equations8 Questions
Exam 4: Square Roots8 Questions
Exam 5: Review of Angle Measure8 Questions
Exam 6: Conversion of Length Measure8 Questions
Exam 7: Standard Weight Pipe8 Questions
Exam 8: Allowance for Threaded Fittings3 Questions
Exam 9: Copper Tubing8 Questions
Exam 10: Allowances for Copper Fittings1 Questions
Exam 11: Plastic Pipe8 Questions
Exam 12: Allowance for Plastic Fittings1 Questions
Exam 13: Welded Steel Pipe8 Questions
Exam 14: Allowing for Welded Fittings8 Questions
Exam 15: Equal Spacing8 Questions
Exam 16: Angles in Plumbing8 Questions
Exam 17: Offset, Diagonal, Rise and Run8 Questions
Exam 18: Solving With 45 Degree Constants2 Questions
Exam 19: Three-Pipe Diagrams With a 45 Degree Offset8 Questions
Exam 20: Right Angle With a 45 Degree Offset8 Questions
Exam 21: 45 Degree Offsets With a Wye Fitting8 Questions
Exam 21: Wye and Tee-Wye Assemblies8 Questions
Exam 23: The 0.707 Constant in 45 Degree Pipe Assemblies8 Questions
Exam 24: Solving for Other Angles8 Questions
Exam 25: Pipe Bending8 Questions
Exam 26: Cast Iron Pipe8 Questions
Exam 27: Cast Iron Assemblies With Various Bends8 Questions
Exam 28: Assemblies With Cast Iron Wyes and Tee-Wyes8 Questions
Exam 29: Single-Loop Back-Venting8 Questions
Exam 30: Grade, Percent Grade, Drop and Run8 Questions
Exam 31: Elevation and Grade8 Questions
Exam 32: Elevation in a Plan View Pipe Diagram8 Questions
Exam 33: Jumper Offsets8 Questions
Exam 34: 45 Degree Offsets in Parallel8 Questions
Exam 35: Special Case of 45 Degree Offsets in Parallel8 Questions
Exam 36: Rolling Offsets8 Questions
Exam 37: Combination Offsets8 Questions
Exam 38: Pipe Length by Layout8 Questions
Exam 39: Cast Iron Flanged Fittings8 Questions
Exam 40: Miter Cuts - Welded Pipe8 Questions
Exam 41: Shower Pan or Safe8 Questions
Exam 42: Rectangular Tank Liner8 Questions
Exam 43: Cylindrical Stretchouts8 Questions
Exam 44: Roof Pitch8 Questions
Exam 45: Water Measure8 Questions
Exam 46: Rectangular Solids8 Questions
Exam 47: Cylinders8 Questions
Exam 48: Spheres8 Questions
Exam 49: Segments8 Questions
Exam 50: Partially Filled Containers of Varying Shapes8 Questions
Exam 51: Water Pressure, Head, and Force8 Questions
Exam 52: Ratio of Pipe Capacities8 Questions
Exam 53: Pipe Sizing8 Questions
Exam 54: Mechanical Advantage8 Questions
Exam 55: The States of Matter and Why It Matters8 Questions
Exam 56: Properties of Gases8 Questions
Exam 57: Heat Loss Vs Radiator Size8 Questions
Exam 58: Radiation Sizing for Total Heat Loss of a Room8 Questions
Exam 59: Estimating Sizing of Piping8 Questions
Exam 60: Sizing Ventilation8 Questions
Exam 61: Heating Rroblems for a Two Floor House8 Questions
Exam 62: Math Aids in Leveling8 Questions
Exam 63: Starting a Business7 Questions
Exam 64: Taking Care of Business8 Questions
Select questions type
The center to center measurement is always _______ the end to end measurement.
Free
(Short Answer)
4.9/5 
(32)
(32) Correct Answer:
Verified
Verifiedgreater than
The back-to-back measurement is always _____________ the end-to-end measurement.
Free
(Short Answer)
4.8/5 (35)
(35) Correct Answer:Verified
Verifiedgreater than
The allowance for a given fitting is the distance between the end of the pipe and the
Free
(Short Answer)
4.9/5 (42)
(42) Correct Answer:Verified
Verifiedcenter of the fitting
Filters
- Essay(0)
- Multiple Choice(0)
- Short Answer(0)
- True False(0)
- Matching(0)