Question 1

Which Cisco IOS command is used to enable a switch interface to become a routed port?

Accepted Answer

A)  sdm prefer routing 
B)  ip route enable 
C)  no switchport 
D)  ip routing 
A)  sdm prefer routing 
B)  ip route enable 
C)  no switchport 
D)  ip routing C

Question 2

Which Cisco IOS command would be used to display the state and type of EtherChannel configured on a device?

Accepted Answer

A)  show running-config 
B)  show ether channel 
C)  show etherchannel summary 
D)  show interface bundle 
A)  show running-config 
B)  show ether channel 
C)  show etherchannel summary 
D)  show interface bundle C

Question 3

Which Cisco IOS command(s) would be used to configure an interface in a static layer 3 EtherChannel?

Accepted Answer

A)  channel-group number mode on 
B)  no switchport 
C)  channel-group number mode on layer-3 
D)  ip routing enable 
A)  channel-group number mode on 
B)  no switchport 
C)  channel-group number mode on layer-3 
D)  ip routing enable A, B

Question 4

Which of the LAN routing options shown is not typically used?

Accepted Answer

A)  Using a layer 3 switch using routed ports 
B)  Using a layer 3 switch using SVIs 
C)  Using a router configured with a VLAN trunk 
D)  Using a router with a physical interface associated with each individual VLAN 
A)  Using a layer 3 switch using routed ports 
B)  Using a layer 3 switch using SVIs 
C)  Using a router configured with a VLAN trunk 
D)  Using a router with a physical interface associated with each individual VLAN

Question 5

Which Cisco IOS command is used to enable IPv4 routing on a 2960 series switch?

Accepted Answer

A)  sdm prefer lanbase-routing 
B)  ip routing 
C)  sdm prefer ipv4-routing 
D)  routing enable 
A)  sdm prefer lanbase-routing 
B)  ip routing 
C)  sdm prefer ipv4-routing 
D)  routing enable

Question 6

Which Cisco IOS command can be used to display the ROAS configuration on a router?

Accepted Answer

A)  show roas 
B)  show vlan 
C)  show vlans 
D)  show interfaces vlan 
A)  show roas 
B)  show vlan 
C)  show vlans 
D)  show interfaces vlan

Question 7

Which Cisco IOS command is used to enable a router subinterface with 802.1Q and associate it with a specific VLAN?

Accepted Answer

A)  vlan vlan-id 
B)  encapsulation dot1q vlan-id 
C)  encapsulation vlan vlan-id 
D)  dot1q vlan-id 
A)  vlan vlan-id 
B)  encapsulation dot1q vlan-id 
C)  encapsulation vlan vlan-id 
D)  dot1q vlan-id

Question 8

Which Cisco IOS command is used to make memory space available for IPv4 routes on a 2960 series of switches?

Accepted Answer

A)  sdm prefer lanbase-routing 
B)  sdm prefer ipv4-routing 
C)  ip routing 
D)  routing enable 
A)  sdm prefer lanbase-routing 
B)  sdm prefer ipv4-routing 
C)  ip routing 
D)  routing enable

Question 9

Which Cisco IOS command can be used on a switch to verify that a trunk has been configured on the interface connected to a router configured with ROAS and the VLANs that are allowed, not blocked, and not pruned?

Accepted Answer

A)  show interfaces roas 
B)  show trunk 
C)  show vlans 
D)  show interfaces trunk 
A)  show interfaces roas 
B)  show trunk 
C)  show vlans 
D)  show interfaces trunk

Question 10

Which Cisco IOS command can be used on a switch to verify that an interface has been configured as a routed port by indicating that it is "routed"?

Accepted Answer

A)  show interfaces 
B)  show interface interface switchport 
C)  show ip route 
D)  show interface status 
A)  show interfaces 
B)  show interface interface switchport 
C)  show ip route 
D)  show interface status

Question 11

When configuring a switch to connect to a router that is being configured with a ROAS configuration, which Cisco IOS command must be entered on the interface to ensure that the link forms a trunk?

Accepted Answer

A)  switchport mode trunk 
B)  switchport mode dynamic desirable 
C)  switchport mode access 
D)  switchport mode trunk router 
A)  switchport mode trunk 
B)  switchport mode dynamic desirable 
C)  switchport mode access 
D)  switchport mode trunk router

Question 12

Which Cisco IOS command is used to create a new SVI on a switch?

Accepted Answer

A)  interface vlan vlan-id 
B)  vlan vlan-id 
C)  switchport access vlan vlan-id 
D)  interface svi vlan-id 
A)  interface vlan vlan-id 
B)  vlan vlan-id 
C)  switchport access vlan vlan-id 
D)  interface svi vlan-id

Question 13

If configuring a layer 3 EtherChannel using two physical interfaces, how many different times must the no switchport command be configured?

Accepted Answer

A)  1 
B)  2 
C)  3 
D)  Never 
A)  1 
B)  2 
C)  3 
D)  Never

Question 14

For a VLAN SVI to be in the up/up state, which option is not required?

Accepted Answer

A)  The VLAN must be defined locally. 
B)  The VLAN must have an entry in the MAC address table. 
C)  An access link or trunk must be configured and optional in the VLAN (not blocked or pruned). 
D)  The VLAN SVI must be enabled. 
A)  The VLAN must be defined locally. 
B)  The VLAN must have an entry in the MAC address table. 
C)  An access link or trunk must be configured and optional in the VLAN (not blocked or pruned). 
D)  The VLAN SVI must be enabled.

Question 15

Which Cisco IOS command would be used to configure a router subinterface to handle any native VLAN traffic?

Accepted Answer

A)  dot1q native 
B)  vlan vlan-id native 
C)  native vlan 
D)  encapsulation dot1q vlan-id native 
A)  dot1q native 
B)  vlan vlan-id native 
C)  native vlan 
D)  encapsulation dot1q vlan-id native

Exam 17: IP Routing in the Lan

Which Cisco IOS command is used to enable a switch interface to become a routed port?

Which Cisco IOS command would be used to display the state and type of EtherChannel configured on a device?

Which Cisco IOS command(s) would be used to configure an interface in a static layer 3 EtherChannel?

Which of the LAN routing options shown is not typically used?

Which Cisco IOS command is used to enable IPv4 routing on a 2960 series switch?

Which Cisco IOS command can be used to display the ROAS configuration on a router?

Which Cisco IOS command is used to enable a router subinterface with 802.1Q and associate it with a specific VLAN?

Which Cisco IOS command is used to make memory space available for IPv4 routes on a 2960 series of switches?

Which Cisco IOS command can be used on a switch to verify that a trunk has been configured on the interface connected to a router configured with ROAS and the VLANs that are allowed, not blocked, and not pruned?

Which Cisco IOS command can be used on a switch to verify that an interface has been configured as a routed port by indicating that it is "routed"?

When configuring a switch to connect to a router that is being configured with a ROAS configuration, which Cisco IOS command must be entered on the interface to ensure that the link forms a trunk?

Which Cisco IOS command is used to create a new SVI on a switch?

If configuring a layer 3 EtherChannel using two physical interfaces, how many different times must the no switchport command be configured?

For a VLAN SVI to be in the up/up state, which option is not required?

Which Cisco IOS command would be used to configure a router subinterface to handle any native VLAN traffic?

Introduction to TCP/IP Networking

Fundamentals of Ethernet Lans

Fundamentals of Wans and IP Routing

Using the Command-Line Interface

Analyzing Ethernet Lan Switching

Configuring Basic Switch Management

Configuring and Verifying Switch Interfaces

Implementing Ethernet Virtual Lans

Spanning Tree Protocol Concepts

RSTP and Etherchannel Configuration

Perspectives on IPV4 Subnetting

Analyzing Classful IPV4 Networks

Analyzing Subnet Masks

Analyzing Existing Subnets

Operating Cisco Routers

Configuring IPV4 Addresses and Static Routes

Troubleshooting IPV4 Routing

Understanding OSPF Concepts

Implementing OSPF

OSPF Network Types and Neighbors

Fundamentals of IP Version 6

Ipv6 Addressing and Subnetting

Implementing IPV6 Addressing on Routers

Implementing IPV6 Routing

Fundamentals of Wireless Networks

Analyzing Cisco Wireless Architectures

Securing Wireless Networks

Building a Wireless Lan

Filters