Question 1

Match each item with a statement below.
a.distance-vector protocol
b.fragment-free switching
c.cut-through switching
d.store-and-forward switching
e.Spanning Tree Protocol
f.trunk port
g.EGP
h.link-state protocol
i.metric
j.IGP
-routing protocol category in which the routing protocol is used to exchange routing information within an autonomous system

Accepted Answer

j

Question 2

What has occurred when all routers in a network have accurate information after a change in the network?

Accepted Answer

A)   delivery
B)   convergence
C)   congestion
D)   concurrence B

Question 3

Routers can be used to control network access by inspecting the source and destination address information of packets.

Accepted Answer

A) True 
 B)False  True

Question 4

Match each item with a statement below.
a.distance-vector protocol
b.fragment-free switching
c.cut-through switching
d.store-and-forward switching
e.Spanning Tree Protocol
f.trunk port
g.EGP
h.link-state protocol
i.metric
j.IGP
-damaged frames do not get forwarded

Accepted Answer

The answer of Match each item with a statement below.
a.distance-vector...

Question 5

Match each item with a statement below.
a.distance-vector protocol
b.fragment-free switching
c.cut-through switching
d.store-and-forward switching
e.Spanning Tree Protocol
f.trunk port
g.EGP
h.link-state protocol
i.metric
j.IGP
-frame is sent to the destination port immediately after reading the destination and source MAC address

Accepted Answer

The answer of Match each item with a statement below.
a.distance-vector...

Question 6

On a router configured to use RIP, the number of routers a packet must travel through before it reaches its destination is called what? (Choose two.)

Accepted Answer

A)   metric
B)   hop count
C)   timestamp
D)   aging time

Question 7

Which of the following combinations will you find in a switching table?

Accepted Answer

A)   application/destination port number
B)   IP address/exit interface
C)   destination network/next Hop
D)   MAC address/switch port number

Question 8

What is BGP and how is it used?

Accepted Answer

The answer of What is BGP and how is it...

Question 9

What command issued from a command prompt will display the routing table in Windows?

Accepted Answer

A)   route table
B)   route print
C)   route delete
D)   route config

Question 10

One type of security for wireless networks involves entering a list of the MAC addresses for the devices that are allowed to access the network and excluding all others. This is called MAC ____________.

Accepted Answer

The answer of One type of security for wireless networks...

Question 11

Which of the following is the fastest switching mode?

Accepted Answer

A)   cut-through
B)   fragment-free
C)   store-and-forward
D)   auto-negotiate

Question 12

A ____________ is used to make connections between the network interface card and the other vital components of the computer, such as the central processing unit.

Accepted Answer

The answer of A ____________ is used to make connections...

Question 13

Briefly describe the three types of switching methods.

Accepted Answer

The answer of Briefly describe the three types of switching...

Question 14

Match each item with a statement below.
a.distance-vector protocol
b.fragment-free switching
c.cut-through switching
d.store-and-forward switching
e.Spanning Tree Protocol
f.trunk port
g.EGP
h.link-state protocol
i.metric
j.IGP
-designed to stop switching loops

Accepted Answer

The answer of Match each item with a statement below.
a.distance-vector...

Question 15

What type of hacker uses a scanning device to find unsecured wireless networks and breaks into those networks?

Accepted Answer

A)   white hat
B)   wardriver
C)   script kiddy
D)   phisher

Question 16

Which of the following is NOT a function that would be found in a managed switch?

Accepted Answer

A)   the ability to stop switching loops using STP
B)   the ability to transfer its switching table with neighboring switches
C)   the creation of VLANS to logically separate resources
D)   to limit access to the network by enabling security on individual ports

Question 17

What category of routing protocol is used to route packets between autonomous systems?

Accepted Answer

A)   distance-vector
B)   link-state
C)   EGP
D)   IGP

Question 18

Match each item with a statement below.
a.distance-vector protocol
b.fragment-free switching
c.cut-through switching
d.store-and-forward switching
e.Spanning Tree Protocol
f.trunk port
g.EGP
h.link-state protocol
i.metric
j.IGP
-value that tells routers the best path to the destination network

Accepted Answer

The answer of Match each item with a statement below.
a.distance-vector...

Question 19

When a router's interface is configured to connect with a switch trunk port to route packets between VLANs, what is this called?

Accepted Answer

A)   multi-homed router
B)   dynamic router
C)   link-state router
D)   router on a stick

Question 20

In general, what level of security should you use with your access points?

Accepted Answer

A)   the easiest to configure
B)   wireless encryption protocol
C)   the most secure your systems supports
D)   RADIUS

Exam 8: Network Hardware in Depth

What has occurred when all routers in a network have accurate information after a change in the network?

Routers can be used to control network access by inspecting the source and destination address information of packets.

Match each item with a statement below. a.distance-vector protocol b.fragment-free switching c.cut-through switching d.store-and-forward switching e.Spanning Tree Protocol f.trunk port g.EGP h.link-state protocol i.metric j.IGP -damaged frames do not get forwarded

On a router configured to use RIP, the number of routers a packet must travel through before it reaches its destination is called what? (Choose two.)

Which of the following combinations will you find in a switching table?

What is BGP and how is it used?

What command issued from a command prompt will display the routing table in Windows?

One type of security for wireless networks involves entering a list of the MAC addresses for the devices that are allowed to access the network and excluding all others. This is called MAC ____________.

Which of the following is the fastest switching mode?

A ____________ is used to make connections between the network interface card and the other vital components of the computer, such as the central processing unit.

Briefly describe the three types of switching methods.

Match each item with a statement below. a.distance-vector protocol b.fragment-free switching c.cut-through switching d.store-and-forward switching e.Spanning Tree Protocol f.trunk port g.EGP h.link-state protocol i.metric j.IGP -designed to stop switching loops

What type of hacker uses a scanning device to find unsecured wireless networks and breaks into those networks?

Which of the following is NOT a function that would be found in a managed switch?

What category of routing protocol is used to route packets between autonomous systems?

Match each item with a statement below. a.distance-vector protocol b.fragment-free switching c.cut-through switching d.store-and-forward switching e.Spanning Tree Protocol f.trunk port g.EGP h.link-state protocol i.metric j.IGP -value that tells routers the best path to the destination network

When a router's interface is configured to connect with a switch trunk port to route packets between VLANs, what is this called?

In general, what level of security should you use with your access points?