Question 1

What is the administrative distance of a static route?

Accepted Answer

A) 110 
B) 120 
C) 1 
D) 90 
E) 100 
A) 110 
B) 120 
C) 1 
D) 90 
E) 100 C

Question 2

What is the administrative distance for RIP in Cisco networking?

Accepted Answer

A) 10 
B) 90 
C) 110 
D) 120 
A) 10 
B) 90 
C) 110 
D) 120 D

Question 3

What is the administrative distance for a static route in Cisco networking?

Accepted Answer

A) 1 
B) 0 
C) 10 
D) 20 
A) 1 
B) 0 
C) 10 
D) 20 A

Question 4

What is the administrative distance for OSPF in Cisco networking?

Accepted Answer

A) 10 
B) 90 
C) 110 
D) 120 
A) 10 
B) 90 
C) 110 
D) 120

Question 5

What is the number 10 in the command router ospf 10?

Accepted Answer

A) Tag 
B) Process ID 
C) AS number 
D) Metric 
A) Tag 
B) Process ID 
C) AS number 
D) Metric

Question 6

What is the administrative distance for a directly connected route in Cisco networking?

Accepted Answer

A) 1 
B) 0 
C) 10 
D) 20 
A) 1 
B) 0 
C) 10 
D) 20

Question 7

Which of the following router commands could be used to display the routing protocol configured on the router?

Accepted Answer

A) router>sh ip protocol detail 
B) router# sh ip protocol 
C) router# sh protocol 
D) All of these answers are correct 
A) router>sh ip protocol detail 
B) router# sh ip protocol 
C) router# sh protocol 
D) All of these answers are correct

Question 8

Which prompt is displayed after issuing the command to enable RIP routing?

Accepted Answer

A) router(config-router-rip)# 
B) router(config-router) 
C) router#(config-router) 
D) router(config-router)# 
E) router#(config-router-rip) 
A) router(config-router-rip)# 
B) router(config-router) 
C) router#(config-router) 
D) router(config-router)# 
E) router#(config-router-rip)

Question 9

Which of the following best characterizes areas in the OSPF protocol?

Accepted Answer

A) Not used 
B) Used to partition a large network into small networks 
C) Used to combine small networks into one large network 
D) An inefficient use of bandwidth 
A) Not used 
B) Used to partition a large network into small networks 
C) Used to combine small networks into one large network 
D) An inefficient use of bandwidth

Question 10

All subnets that are attached to Router2 for the network shown in the following figure are:
10.20.100.0
10.50.10.0

Accepted Answer

A) True 
 B)False

Question 11

Which of the following best characterizes OSPF's Area 0?

Accepted Answer

A) Used to hide data packets 
B) Root or the backbone for the network 
C) Inverse mask bits 
D) Route selection bits 
A) Used to hide data packets 
B) Root or the backbone for the network 
C) Inverse mask bits 
D) Route selection bits

Question 12

What is the purpose of variable length subnet masks?

Accepted Answer

A) They are not recommended in modern computer networks. 
B) They minimize wasted IP address space when interconnecting subnets. 
C) They reduce the number of bits required in a subnet mask from 32 to 24. 
D) They are the same as classful addressing. 
A) They are not recommended in modern computer networks. 
B) They minimize wasted IP address space when interconnecting subnets. 
C) They reduce the number of bits required in a subnet mask from 32 to 24. 
D) They are the same as classful addressing.

Question 13

Select the command that can be used to route a data packet route out of your current LAN if a route to the specified destination has not been entered into the router's routing table.The destination IP address is 192.168.12.3.The subnet mask being used for the LAN is /26.The next hop IP address is 192.168.12.66.

Accepted Answer

A) router(config)# ip route 0.0.0.0 0.0.0.0 192.168.12.66 
B) router(config)# ip route 192.168.12.66 0.0.0.0 0.0.0.0 
C) router>ip route 0.0.0.0 0.0.0.0 192.168.12.66 
D) router>ip route 192.168.12.66 0.0.0.0 0.0.0.0 
A) router(config)# ip route 0.0.0.0 0.0.0.0 192.168.12.66 
B) router(config)# ip route 192.168.12.66 0.0.0.0 0.0.0.0 
C) router>ip route 0.0.0.0 0.0.0.0 192.168.12.66 
D) router>ip route 192.168.12.66 0.0.0.0 0.0.0.0

Question 14

What is the administrative distance for EIGRP in Cisco networking?

Accepted Answer

A) 10 
B) 90 
C) 110 
D) 120 
A) 10 
B) 90 
C) 110 
D) 120

Question 15

Advertising a network means the routing table containing the network is shared with its neighbor routers.

Accepted Answer

A) True 
 B)False

Question 16

You want to configure EIGRP on five interfaces all in the 10.X.X.X network range using a single command.What command does this?

Accepted Answer

A) network 10.0.0.0 
B) network 10.0.0.0 255.0.0.0 
C) network 10.0.0.0 0.255.255.255 area 0 
D) network 10.0.0.0 mask 255.0.0.0 
A) network 10.0.0.0 
B) network 10.0.0.0 255.0.0.0 
C) network 10.0.0.0 0.255.255.255 area 0 
D) network 10.0.0.0 mask 255.0.0.0

Question 17

Which of the following does the OSPF routing protocol use to verify that a link between to routers is active and the routers are communicating?

Accepted Answer

A) LSAs 
B) ARP messages 
C) Ping 
D) "Hello" packets 
A) LSAs 
B) ARP messages 
C) Ping 
D) "Hello" packets

Question 18

What command will provide information about the dynamic routing protocols on your Cisco router and their configurations?

Accepted Answer

A) show protocol 
B) show ip protocol 
C) show protocol dynamic 
D) show protocol link-state 
A) show protocol 
B) show ip protocol 
C) show protocol dynamic 
D) show protocol link-state

Question 19

What mode are you in when you use the network command to configure OSPF?

Accepted Answer

A) (config) 
B) (config-if) 
C) (config-router) 
D) (config-ospf) 
A) (config) 
B) (config-if) 
C) (config-router) 
D) (config-ospf)

Question 20

A computer with an IP address of 10.10.5.1 sends a data packet with a destination IP address of 10.5.10.20 using a subnet mask of 255.255.255.0.The packet stays in the LAN.

Accepted Answer

A) True 
 B)False

What is the administrative distance of a static route?

What is the administrative distance for RIP in Cisco networking?

What is the administrative distance for a static route in Cisco networking?

What is the administrative distance for OSPF in Cisco networking?

What is the number 10 in the command router ospf 10?

What is the administrative distance for a directly connected route in Cisco networking?

Which of the following router commands could be used to display the routing protocol configured on the router?

Which prompt is displayed after issuing the command to enable RIP routing?

Which of the following best characterizes areas in the OSPF protocol?

All subnets that are attached to Router2 for the network shown in the following figure are: 10.20.100.0 10.50.10.0

Which of the following best characterizes OSPF's Area 0?

What is the purpose of variable length subnet masks?

What is the administrative distance for EIGRP in Cisco networking?

Advertising a network means the routing table containing the network is shared with its neighbor routers.

You want to configure EIGRP on five interfaces all in the 10.X.X.X network range using a single command.What command does this?

Which of the following does the OSPF routing protocol use to verify that a link between to routers is active and the routers are communicating?

What command will provide information about the dynamic routing protocols on your Cisco router and their configurations?

What mode are you in when you use the network command to configure OSPF?

A computer with an IP address of 10.10.5.1 sends a data packet with a destination IP address of 10.5.10.20 using a subnet mask of 255.255.255.0.The packet stays in the LAN.

Introduction to Computer Networks

Physical Layer Cabling: Twisted Pair

Physical Layer Cabling: Fiber Optics

Wireless Networking

Interconnecting the Lans

Tcp/Ip

Introduction to Router Configuration

Introduction to Switch Configuration

Internet Technologies: Out to the Internet

Troubleshooting

Network Security

Cloud Computing and Virtualization

Codes and Standards

Filters

Exam 9: Routing Protocols

What is the administrative distance of a static route?

What is the administrative distance for RIP in Cisco networking?

What is the administrative distance for a static route in Cisco networking?

What is the administrative distance for OSPF in Cisco networking?

What is the number 10 in the command router ospf 10?

What is the administrative distance for a directly connected route in Cisco networking?

Which of the following router commands could be used to display the routing protocol configured on the router?

Which prompt is displayed after issuing the command to enable RIP routing?

Which of the following best characterizes areas in the OSPF protocol?

All subnets that are attached to Router2 for the network shown in the following figure are: 10.20.100.0 10.50.10.0

Which of the following best characterizes OSPF's Area 0?

What is the purpose of variable length subnet masks?

What is the administrative distance for EIGRP in Cisco networking?

Advertising a network means the routing table containing the network is shared with its neighbor routers.

You want to configure EIGRP on five interfaces all in the 10.X.X.X network range using a single command.What command does this?

Which of the following does the OSPF routing protocol use to verify that a link between to routers is active and the routers are communicating?

What command will provide information about the dynamic routing protocols on your Cisco router and their configurations?

What mode are you in when you use the network command to configure OSPF?

A computer with an IP address of 10.10.5.1 sends a data packet with a destination IP address of 10.5.10.20 using a subnet mask of 255.255.255.0.The packet stays in the LAN.

Introduction to Computer Networks

Physical Layer Cabling: Twisted Pair

Physical Layer Cabling: Fiber Optics

Wireless Networking

Interconnecting the Lans

Tcp/Ip

Introduction to Router Configuration

Introduction to Switch Configuration

Internet Technologies: Out to the Internet

Troubleshooting

Network Security

Cloud Computing and Virtualization

Codes and Standards

Filters