Question 1

Which of the following is not true regarding a secondary auxiliary view?

Accepted Answer

A) It is projected directly from the primary auxiliary view. 
B) Many times the secondary auxiliary view is completed first. 
C)  A secondary auxiliary view is always created. 
D)  none of the above 
A) It is projected directly from the primary auxiliary view. 
B) Many times the secondary auxiliary view is completed first. 
C)  A secondary auxiliary view is always created. 
D)  none of the above C

Question 2

A round surface is divided into twelve points and labeled in a clockwise direction.

Accepted Answer

A) True 
 B)False  True

Question 3

A reference line is placed in the center of a circle for the auxiliary view of a pipe.

Accepted Answer

A) True 
 B)False  False

Question 4

Lines that are not true length in the auxiliary should be:

Accepted Answer

A) drawn lighter 
B) omitted 
C)  drawn as a hidden line 
D)  not altered at all 
A) drawn lighter 
B) omitted 
C)  drawn as a hidden line 
D)  not altered at all

Question 5

A primary auxiliary view must be drawn before a secondary auxiliary view can be drawn.

Accepted Answer

A) True 
 B)False

Question 6

An auxiliary view is a projection that is parallel to an inclined surface.

Accepted Answer

A) True 
 B)False

Question 7

A primary auxiliary view is parallel to one of the principal planes of projection.

Accepted Answer

A) True 
 B)False

Question 8

When drawing an auxiliary view, projection lines must be drawn at what angle from the inclined surface?

Accepted Answer

A) 60 degrees 
B) 45 degrees 
C)  90 degrees 
D)  none of the above 
A) 60 degrees 
B) 45 degrees 
C)  90 degrees 
D)  none of the above

Question 9

A partial auxiliary view makes it possible to eliminate one or more of the regular views.

Accepted Answer

A) True 
 B)False

Question 10

The line of sight for an auxiliary view drawing is located ____ to the edge view of the inclined surface.

Accepted Answer

A) parallel 
B) perpendicular 
C)  inclined 
D)  foreshortened 
A) parallel 
B) perpendicular 
C)  inclined 
D)  foreshortened

Question 11

A reference line should be drawn horizontally and pass through as many points as possible.

Accepted Answer

A) True 
 B)False

Question 12

A surface shown true size and shape in an auxiliary view would be ____ on the principal view.

Accepted Answer

A) Length 
B) foreshortened 
C)  normal 
D)  true shape 
A) Length 
B) foreshortened 
C)  normal 
D)  true shape

Question 13

A primary auxiliary view is inclined to at least two of the three principal planes of projection.

Accepted Answer

A) True 
 B)False

Question 14

Which of the following is not true regarding an auxiliary sectional view?

Accepted Answer

A) it is an auxiliary view in sections. 
B) It is drawn exactly as is any removed section view. 
C)  Generally, only the surface cut by the cutting-plane line is drawn. 
D)  Not all of the auxiliary view rules apply. 
A) it is an auxiliary view in sections. 
B) It is drawn exactly as is any removed section view. 
C)  Generally, only the surface cut by the cutting-plane line is drawn. 
D)  Not all of the auxiliary view rules apply.

Question 15

Use of the half auxiliary is very common because it saves time.

Accepted Answer

A) True 
 B)False

Question 16

It is necessary to draw a secondary auxiliary view when:

Accepted Answer

A) the primary auxiliary view does not have enough detail 
B) the primary auxiliary view contains oblique surfaces 
C)  the primary auxiliary view is not true shape 
D)  all of the above 
A) the primary auxiliary view does not have enough detail 
B) the primary auxiliary view contains oblique surfaces 
C)  the primary auxiliary view is not true shape 
D)  all of the above

Question 17

A fold line is place in the middle of two adjacent views.

Accepted Answer

A) True 
 B)False

Question 18

When laying out a drawing with an auxiliary view, always choose the view with the most detail as the front view.

Accepted Answer

A) True 
 B)False

Question 19

A pipe cut at a 45-degree angle will appear as a circle in the auxiliary view.

Accepted Answer

A) True 
 B)False

Question 20

Which of the following is not a major kind of auxiliary view?

Accepted Answer

A) front view 
B) top view 
C)  side view 
D)  bottom view 
A) front view 
B) top view 
C)  side view 
D)  bottom view

Exam 9: Auxiliary Views

Which of the following is not true regarding a secondary auxiliary view?

A round surface is divided into twelve points and labeled in a clockwise direction.

A reference line is placed in the center of a circle for the auxiliary view of a pipe.

Lines that are not true length in the auxiliary should be:

A primary auxiliary view must be drawn before a secondary auxiliary view can be drawn.

An auxiliary view is a projection that is parallel to an inclined surface.

A primary auxiliary view is parallel to one of the principal planes of projection.

When drawing an auxiliary view, projection lines must be drawn at what angle from the inclined surface?

A partial auxiliary view makes it possible to eliminate one or more of the regular views.

The line of sight for an auxiliary view drawing is located ____ to the edge view of the inclined surface.

A reference line should be drawn horizontally and pass through as many points as possible.

A surface shown true size and shape in an auxiliary view would be ____ on the principal view.

A primary auxiliary view is inclined to at least two of the three principal planes of projection.

Which of the following is not true regarding an auxiliary sectional view?

Use of the half auxiliary is very common because it saves time.

It is necessary to draw a secondary auxiliary view when:

A fold line is place in the middle of two adjacent views.

When laying out a drawing with an auxiliary view, always choose the view with the most detail as the front view.

A pipe cut at a 45-degree angle will appear as a circle in the auxiliary view.

Which of the following is not a major kind of auxiliary view?

Introduction

Employability Skills for Drafting and Design Technicians

Drafting Tools: Conventional, Cad, and Solid Modeling

Sketching and Lettering for Engineering Communication

Geometric Construction

Spatial Visualization and Multiview Drawings

Dimensioning and Notation

Sectional Views

Descriptive Geometry

Patterns and Developments

Solid 3D Modeling: Computational Design and Analysis

Geometric Dimensioning and Tolerancing

Fasteners

Springs

Cams

Gears

Assembly and Detail Drawings for Design

Pictorial Drawings

Welding

Modern Manufacturing: Materials, Processes, and Automation

The Design Process and Advanced Concepts

Filters