Question 1

​What must be done if a removed section must be placed on another page other than the page on which the cutting plane line is placed?

Accepted Answer

A) ​The page where the removed section is located must refer back to the page from where it was taken. 
B) ​A page number cross reference must be given as to where the removed section may be found. 
C)  ​both A and B 
D)  ​none of the above 
A) ​The page where the removed section is located must refer back to the page from where it was taken. 
B) ​A page number cross reference must be given as to where the removed section may be found. 
C)  ​both A and B 
D)  ​none of the above C

Question 2

​This type of section illustrates both the exterior and interior of the object.

Accepted Answer

A) ​half 
B) ​offset 
C)  ​removed 
D)  ​broken-out 
A) ​half 
B) ​offset 
C)  ​removed 
D)  ​broken-out A

Question 3

​In a true projection, a keyway is not shown in the hole.

Accepted Answer

A) True 
 B)False  True

Question 4

​This is not included on an assembly section drawing.

Accepted Answer

A) ​legend 
B) ​parts list 
C)  ​notes 
D)  ​parts 
A) ​legend 
B) ​parts list 
C)  ​notes 
D)  ​parts

Question 5

​Hidden lines are usually not used in a section view.

Accepted Answer

A) True 
 B)False

Question 6

​This practice is used when holes located around a bolt circle are not aligned with the cutting plane line.

Accepted Answer

A) ​alternate section lining 
B) ​aligning of sections 
C)  ​aligning of features 
D)  ​rotating section views 
A) ​alternate section lining 
B) ​aligning of sections 
C)  ​aligning of features 
D)  ​rotating section views

Question 7

​A section view usually shows _____ details.

Accepted Answer

A) ​exterior 
B) ​interior 
C)  ​profile 
D)  ​foreshortened 
A) ​exterior 
B) ​interior 
C)  ​profile 
D)  ​foreshortened

Question 8

​The direction of sight of a section is indicated by the:

Accepted Answer

A) ​viewing direction of the section 
B) ​arrows at the end of the cutting plane line 
C)  ​offset section in the section 
D)  ​dashed lines on the section 
A) ​viewing direction of the section 
B) ​arrows at the end of the cutting plane line 
C)  ​offset section in the section 
D)  ​dashed lines on the section

Question 9

A true projection of a sectional view always produces the actual shape of the object.

Accepted Answer

A) True 
 B)False

Question 10

​Section lining should be parallel with the sides of the object to be section lined.

Accepted Answer

A) True 
 B)False

Question 11

​Which of the following is not true of section lines.

Accepted Answer

A) ​They should be evenly spaced by eye. 
B) ​They must be of uniform thickness. 
C)  ​The average spacing used for most drawings is 3mm. 
D)  ​They are generally drawn at 60 degrees to the horizon. 
A) ​They should be evenly spaced by eye. 
B) ​They must be of uniform thickness. 
C)  ​The average spacing used for most drawings is 3mm. 
D)  ​They are generally drawn at 60 degrees to the horizon.

Question 12

​In a broken-out section, part of the cutting plane line is drawn freehand.

Accepted Answer

A) True 
 B)False

Question 13

​If there are two parts on the object, each part is sectioned with lines in different directions.

Accepted Answer

A) True 
 B)False

Question 14

Today, it is recommended to use the removed section rather than the revolved section.​

Accepted Answer

A) True 
 B)False

Question 15

​This type of section is used to make a particular feature of an object easier to understand.

Accepted Answer

A) ​rotated 
B) ​offset 
C)  ​broken-out 
D)  ​removed 
A) ​rotated 
B) ​offset 
C)  ​broken-out 
D)  ​removed

Question 16

​Which of the following is not a list of types of sectional views?

Accepted Answer

A) ​full, half, offset 
B) ​front, back, profile 
C)  ​broken-out, revolved, removed 
D)  ​thinwall, auxiliary, assembly 
A) ​full, half, offset 
B) ​front, back, profile 
C)  ​broken-out, revolved, removed 
D)  ​thinwall, auxiliary, assembly

Question 17

​When a cutting plane line passes through a hole, it should be sectioned with lines in the opposite direction of the rest of the object.

Accepted Answer

A) True 
 B)False

Question 18

​A(n) _____ is a section view drawing in which the cutting plane line is bent.

Accepted Answer

A) ​full section 
B) ​revolved section 
C)  ​offset section 
D)  ​broken-out section 
A) ​full section 
B) ​revolved section 
C)  ​offset section 
D)  ​broken-out section

Question 19

​If a cutting plane line passes lengthwise through the axis of a fastener or shaft, the fastener or shaft is not sectioned.

Accepted Answer

A) True 
 B)False

Question 20

​Half sections are best used when an object is not symmetrical.

Accepted Answer

A) True 
 B)False

Exam 8: Sectional Views

​What must be done if a removed section must be placed on another page other than the page on which the cutting plane line is placed?

​This type of section illustrates both the exterior and interior of the object.

​In a true projection, a keyway is not shown in the hole.

​This is not included on an assembly section drawing.

​Hidden lines are usually not used in a section view.

​This practice is used when holes located around a bolt circle are not aligned with the cutting plane line.

​A section view usually shows _____ details.

​The direction of sight of a section is indicated by the:

A true projection of a sectional view always produces the actual shape of the object.

​Section lining should be parallel with the sides of the object to be section lined.

​Which of the following is not true of section lines.

​In a broken-out section, part of the cutting plane line is drawn freehand.

​If there are two parts on the object, each part is sectioned with lines in different directions.

Today, it is recommended to use the removed section rather than the revolved section.​

​This type of section is used to make a particular feature of an object easier to understand.

​Which of the following is not a list of types of sectional views?

​When a cutting plane line passes through a hole, it should be sectioned with lines in the opposite direction of the rest of the object.

​A(n) _____ is a section view drawing in which the cutting plane line is bent.

​If a cutting plane line passes lengthwise through the axis of a fastener or shaft, the fastener or shaft is not sectioned.

​Half sections are best used when an object is not symmetrical.

Introduction

Employability Skills for Drafting and Design Technicians

Drafting Tools: Conventional, Cad, and Solid Modeling

Sketching and Lettering for Engineering Communication

Geometric Construction

Spatial Visualization and Multiview Drawings

Dimensioning and Notation

Auxiliary Views

Descriptive Geometry

Patterns and Developments

Solid 3D Modeling: Computational Design and Analysis

Geometric Dimensioning and Tolerancing

Fasteners

Springs

Cams

Gears

Assembly and Detail Drawings for Design

Pictorial Drawings

Welding

Modern Manufacturing: Materials, Processes, and Automation

The Design Process and Advanced Concepts

Filters

What must be done if a removed section must be placed on another page other than the page on which the cutting plane line is placed?

This type of section illustrates both the exterior and interior of the object.

In a true projection, a keyway is not shown in the hole.

This is not included on an assembly section drawing.

Hidden lines are usually not used in a section view.

This practice is used when holes located around a bolt circle are not aligned with the cutting plane line.

A section view usually shows _____ details.

The direction of sight of a section is indicated by the:

Section lining should be parallel with the sides of the object to be section lined.

Which of the following is not true of section lines.

In a broken-out section, part of the cutting plane line is drawn freehand.

If there are two parts on the object, each part is sectioned with lines in different directions.

Today, it is recommended to use the removed section rather than the revolved section.

This type of section is used to make a particular feature of an object easier to understand.

Which of the following is not a list of types of sectional views?

When a cutting plane line passes through a hole, it should be sectioned with lines in the opposite direction of the rest of the object.

A(n) _____ is a section view drawing in which the cutting plane line is bent.

If a cutting plane line passes lengthwise through the axis of a fastener or shaft, the fastener or shaft is not sectioned.

Half sections are best used when an object is not symmetrical.