Question 1

​Which of the following would not be a NDT type test of a weld.

Accepted Answer

A)  ​tensile 
B)  ​visual 
C)  ​leak 
D)  ​penetrant 
A)  ​tensile 
B)  ​visual 
C)  ​leak 
D)  ​penetrant

Question 2

____________________ joints are usually welded on only one side.

Accepted Answer

The answer of ____________________ joints are usually welded on only...

Question 3

In the ____ position, the pipe is parallel to the horizon and the weld is made vertically around the pipe.

Accepted Answer

A)  Inclined with a restriction ring 6GR 
B)  Horizontal fixed 5G 
C)  Vertical 2G 
D)  Inclined 6G 
A)  Inclined with a restriction ring 6GR 
B)  Horizontal fixed 5G 
C)  Vertical 2G 
D)  Inclined 6G

Question 4

​What has to be done to ensure that the weld has 100% penetration on thick plate or pipe?

Accepted Answer

A)  ​The part must be preheated to above 350°F (175°
C)  before welding starts. 
B)  ​The welding machine needs to be set on its maximum amperage setting. 
C)  ​Make the molten weld pool as large as possible so it will melt all the way through. 
D)  ​The edges of the weld plate or pipe must have some type of groove made before welding. 
A)  ​The part must be preheated to above 350°F (175°
C)  before welding starts. 
B)  ​The welding machine needs to be set on its maximum amperage setting. 
C)  ​Make the molten weld pool as large as possible so it will melt all the way through. 
D)  ​The edges of the weld plate or pipe must have some type of groove made before welding.

Question 5

In a(n) ____ joint the metal surfaces are placed together so the edges are even.

Accepted Answer

A)  edge 
B)  outside corner 
C)  tee 
D)  lap 
A)  edge 
B)  outside corner 
C)  tee 
D)  lap

Question 6

In a(n) ____ joint the edges of the metal meet so that the thickness of the joint is approximately equal to the thickness of the metal.

Accepted Answer

A)  tee 
B)  lap 
C)  butt 
D)  outside corner 
A)  tee 
B)  lap 
C)  butt 
D)  outside corner

Question 7

The strength value of a seam weld is placed ____ the weld symbol.

Accepted Answer

A)  to the right of 
B)  to the left of 
C)  above 
D)  below 
A)  to the right of 
B)  to the left of 
C)  above 
D)  below

Question 8

When the length of a seam weld is indicated on the symbol, it is shown ____ the weld symbol.

Accepted Answer

A)  to the left of 
B)  to the right of 
C)  above 
D)  below 
A)  to the left of 
B)  to the right of 
C)  above 
D)  below

Question 9

Which of the following is true about choosing a joint design?

Accepted Answer

A)  The ability of a welded joint to withstand stress depends mostly on weld integrity not joint design. 
B)  Base metal does not play a part in joint design. 
C)  The rate of travel, penetration, deposition rate, and heat input affect the welds used on some joint designs. 
D)  The least suitable welding position for most joints is the flat position because it is generally not as strong. 
A)  The ability of a welded joint to withstand stress depends mostly on weld integrity not joint design. 
B)  Base metal does not play a part in joint design. 
C)  The rate of travel, penetration, deposition rate, and heat input affect the welds used on some joint designs. 
D)  The least suitable welding position for most joints is the flat position because it is generally not as strong.

Question 10

Describe how the members of a tee joint come together.

Accepted Answer

In a tee joint the edge of a piece of me

Exam 22: Welding Joint Design and Welding Symbols

​Which of the following would not be a NDT type test of a weld.

____________________ joints are usually welded on only one side.

In the ____ position, the pipe is parallel to the horizon and the weld is made vertically around the pipe.

​What has to be done to ensure that the weld has 100% penetration on thick plate or pipe?

In a(n) ____ joint the metal surfaces are placed together so the edges are even.

In a(n) ____ joint the edges of the metal meet so that the thickness of the joint is approximately equal to the thickness of the metal.

The strength value of a seam weld is placed ____ the weld symbol.

When the length of a seam weld is indicated on the symbol, it is shown ____ the weld symbol.

Which of the following is true about choosing a joint design?

Describe how the members of a tee joint come together.

Introduction to Welding

Safety in Welding

Shielded Metal Arc Equipment, Setup, and Operation

Shielded Metal Arc Welding of Plate

Shielded Metal Arc Welding of Pipe

Shielded Metal Arc Welding Aws Sense Certification

Flame Cutting

Plasma Arc Cutting

Related Cutting Processes

Gas Metal Arc Welding Equipment, Setup, and Operation

Gas Metal Arc Welding

Flux Cored Arc Welding Equipment, Setup, and Operation

Flux Cored Arc Welding

Gas Metal Arc and Flux Cored Arc Welding of Pipe

Gas Metal Arc and Flux Cored Arc Welding Aws Sense Certification

Gas Tungsten Arc Welding Equipment, Setup, Operation, and Filler Metals

Gas Tungsten Arc Welding of Plate

Gas Tungsten Arc Welding of Pipe

Gas Tungsten Arc Welding Plate and Pipe Aws Sense Certification

Shop Math and Weld Cost

Reading Technical Drawings

Fabricating Techniques and Practices

Welding Codes and Standards

Testing and Inspection of Welds

Welding Metallurgy

Weldability of Metals

Filler Metal Selection

Welding Automation and Robotics

Other Welding Processes

Oxyfuel Welding and Cutting Equipment, Setup, and Operation

Oxyacetylene Welding

Brazing, Braze Welding, and Soldering

Filters

Which of the following would not be a NDT type test of a weld.

What has to be done to ensure that the weld has 100% penetration on thick plate or pipe?