Question 1

____________________ is the standard federal government, military, or aerospace terminology denoting a WPS.

Accepted Answer

The answer of ____________________ is the standard federal government, military,...

Question 2

The ____ by the specimen's original area converts the ultimate total load for the specimen to the pounds per square inch (psi) that was required to break the material.

Accepted Answer

A)  minimum load multiplied 
B)  maximum load multiplied 
C)  minimum load divided 
D)  maximum load divided 
A)  minimum load multiplied 
B)  maximum load multiplied 
C)  minimum load divided 
D)  maximum load divided

Question 3

A(n) ____ may require that a specific code or standard be followed, whereas in ____, the code used is considered to be the standard for the industry and has been in use a long time.

Accepted Answer

A)  local, state, or federal government; standard industrial practices 
B)  local, state, or federal government; bonding or insuring companies 
C)  end user, standard industrial practices 
D)  end user, bonding or insuring companies 
A)  local, state, or federal government; standard industrial practices 
B)  local, state, or federal government; bonding or insuring companies 
C)  end user, standard industrial practices 
D)  end user, bonding or insuring companies

Question 4

Unlike the AWS D1.1 or the ASME Section IX, the ____________________ requires a "Nick-Break Test Specimen."

Accepted Answer

The answer of Unlike the AWS D1.1 or the ASME...

Question 5

The welding current should be listed as________________.

Accepted Answer

A)  AC, DCEP, or DCEN 
B)  straight or reverse 
C)  60 cycle 
D)  DCSP or DCRP 
A)  AC, DCEP, or DCEN 
B)  straight or reverse 
C)  60 cycle 
D)  DCSP or DCRP

Question 6

The most commonly used code for pipelines is ____________________.

Accepted Answer

The answer of The most commonly used code for pipelines...

Question 7

What steps must be taken if the test samples do not pass the applicable test in the qualifying and certifying process?

Accepted Answer

If the test samples do not pass the appl

Question 8

____ is a specific grouping number for several classifications of electrodes having similar composition and welding characteristics.

Accepted Answer

A)  Classification number 
B)  Filler metal specification number 
C)  F-number 
D)  A-number 
A)  Classification number 
B)  Filler metal specification number 
C)  F-number 
D)  A-number

Question 9

Which of the following is true about qualifying the WPS?

Accepted Answer

A)  It must be qualified to verify that the list of variables will provide a sound weld. 
B)  It is not necessary to keep a record of all parameters used to produce test welds. 
C)  The PQR is for the benefit of the welder; the inspection agency will not request it. 
D)  Sample welds are prepared using an established code or specification. 
A)  It must be qualified to verify that the list of variables will provide a sound weld. 
B)  It is not necessary to keep a record of all parameters used to produce test welds. 
C)  The PQR is for the benefit of the welder; the inspection agency will not request it. 
D)  Sample welds are prepared using an established code or specification.

Question 10

A qualified WPS is usable for ____.

Accepted Answer

A)  six months 
B)  one year 
C)  an indefinite length of time 
D)  an indefinite length of time, usually until a more efficient process is found 
A)  six months 
B)  one year 
C)  an indefinite length of time 
D)  an indefinite length of time, usually until a more efficient process is found

Question 11

____ is the ASTM specification for the type and grade of material, including the P-number.

Accepted Answer

A)  Filler metal specification 
B)  Electrode specification 
C)  Base metal specification 
D)  Backing strip material specification 
A)  Filler metal specification 
B)  Electrode specification 
C)  Base metal specification 
D)  Backing strip material specification

Question 12

The most commonly used code for pressure vessels and nuclear components is ____________________.

Accepted Answer

The answer of The most commonly used code for pressure...

Question 13

If a welder is not engaged in the specific process of welding for which he or she is qualified for a period exceeding ____, the welder must requalify.

Accepted Answer

A)  two months 
B)  six months 
C)  one year 
D)  two years 
A)  two months 
B)  six months 
C)  one year 
D)  two years

Question 14

____ are those in which a change is considered to affect the mechanical properties of the weldment to the point of requiring requalification of the procedure.

Accepted Answer

A)  Essential variables 
B)  Nonessential variables 
C)  Code parameters 
D)  WPS parameters 
A)  Essential variables 
B)  Nonessential variables 
C)  Code parameters 
D)  WPS parameters

Question 15

In a PQR, flow rate should be recorded in ____.

Accepted Answer

A)  cubic feet per second 
B)  cubic feet per minute 
C)  cubic feet per hour 
D)  square feet per hour 
A)  cubic feet per second 
B)  cubic feet per minute 
C)  cubic feet per hour 
D)  square feet per hour

Question 16

A welding ____________________ is a detailed statement of the legal requirements for a specific classification or type of weld to be made on a specific product.

Accepted Answer

The answer of A welding ____________________ is a detailed statement...

Question 17

If the machine being used for the weld does not have an amp meter, a meter must be attached to the welding lead, within ____ ft. of the electrode holder, to get the reading of the amount of current in amps used to make the weld.

Accepted Answer

A)  one 
B)  two 
C)  three 
D)  four 
A)  one 
B)  two 
C)  three 
D)  four

Question 18

____ is the classification of weld metal analysis.

Accepted Answer

A)  F-number 
B)  A-number 
C)  Filler metal specification number 
D)  Classification number 
A)  F-number 
B)  A-number 
C)  Filler metal specification number 
D)  Classification number

Question 19

Who should supervise the testing of your weld?

Accepted Answer

A)  A friend, so they can help you prepare the test specimens because all of that grinding is hard work 
B)  The person who wrote the code 
C)  Your welding teacher or a school administrator 
D)  The same individual or group that witnessed you taking the test 
A)  A friend, so they can help you prepare the test specimens because all of that grinding is hard work 
B)  The person who wrote the code 
C)  Your welding teacher or a school administrator 
D)  The same individual or group that witnessed you taking the test

Exam 24: Welding Codes and Standards

____________________ is the standard federal government, military, or aerospace terminology denoting a WPS.

The ____ by the specimen's original area converts the ultimate total load for the specimen to the pounds per square inch (psi) that was required to break the material.

A(n) ____ may require that a specific code or standard be followed, whereas in ____, the code used is considered to be the standard for the industry and has been in use a long time.

Unlike the AWS D1.1 or the ASME Section IX, the ____________________ requires a "Nick-Break Test Specimen."

The welding current should be listed as________________.

The most commonly used code for pipelines is ____________________.

What steps must be taken if the test samples do not pass the applicable test in the qualifying and certifying process?

____ is a specific grouping number for several classifications of electrodes having similar composition and welding characteristics.

Which of the following is true about qualifying the WPS?

A qualified WPS is usable for ____.

____ is the ASTM specification for the type and grade of material, including the P-number.

The most commonly used code for pressure vessels and nuclear components is ____________________.

If a welder is not engaged in the specific process of welding for which he or she is qualified for a period exceeding ____, the welder must requalify.

____ are those in which a change is considered to affect the mechanical properties of the weldment to the point of requiring requalification of the procedure.

In a PQR, flow rate should be recorded in ____.

A welding ____________________ is a detailed statement of the legal requirements for a specific classification or type of weld to be made on a specific product.

If the machine being used for the weld does not have an amp meter, a meter must be attached to the welding lead, within ____ ft. of the electrode holder, to get the reading of the amount of current in amps used to make the weld.

____ is the classification of weld metal analysis.

Who should supervise the testing of your weld?

Introduction to Welding

Safety in Welding

Shielded Metal Arc Equipment, Setup, and Operation

Shielded Metal Arc Welding of Plate

Shielded Metal Arc Welding of Pipe

Shielded Metal Arc Welding Aws Sense Certification

Flame Cutting Equipment, Setup, and Operation

Plasma Arc Cutting Equipment, Setup, and Operation

Related Cutting Processes

Gas Metal Arc Welding Equipment, Setup, and Operation

Gas Metal Arc Welding

Flux Cored Arc Welding Equipment, Setup, and Operation

Flux Cored Arc Welding

Gas Metal Arc and Flux Cored Arc Welding of Pipe

Gas Metal Arc and Flux Cored Arc Welding Aws Sense Certification

Gas Tungsten Arc Welding Equipment, Setup, and Operation

Gas Tungsten Arc Welding of Plate

Gas Tungsten Arc Welding of Pipe

Gas Tungsten Arc Welding Plate and Pipe Aws Sense Certification

Shop Math and Weld Cost

Reading Technical Drawings

Welding Joint Design and Welding Symbols

Fabricating Techniques and Practices

Testing and Inspection

Welding Metallurgy

Weldability of Metals

Filler Metal Selection

Welding Automation and Robotics

Other Welding Processes

Oxyfuel Welding Equipment, Setup, and Operation

Oxyacetylene Welding and Brazing, Braze Welding, and Soldering

Filters

A(n) may require that a specific code or standard be followed, whereas in , the code used is considered to be the standard for the industry and has been in use a long time.