Question 1

When a device is new to the market, you should purchase it as soon as possible so that it is at the beginning of its EOL cycle.

Accepted Answer

A) True 
 B)False

Question 2

Bridges cannot route traffic.

Accepted Answer

A) True 
 B)False

Question 3

When designing your network, you may want to have ____________________ so that traffic is rerouted and users never know when equipment is malfunctioning.

Accepted Answer

The answer of When designing your network, you may want...

Question 4

Routers enable you to ____.

Accepted Answer

A) segment networks 
B) control network traffic 
C) establish separate collision domains while ensuring faster flow of network traffic 
D) Both A and B. 
A) segment networks 
B) control network traffic 
C) establish separate collision domains while ensuring faster flow of network traffic 
D) Both A and B.

Question 5

If cable installation costs are high because of requirements to remove hazardous materials or because plenum cable is required, consider using ____________________ solutions as an alternative.

Accepted Answer

The answer of If cable installation costs are high because...

Question 6

RFP stands for ____.

Accepted Answer

A) requirements for processing 
B) request for proposal 
C) request for planning 
D) redundant field plan 
A) requirements for processing 
B) request for proposal 
C) request for planning 
D) redundant field plan

Question 7

In a building with horizontal wiring, each floor represents a discrete unit of cabling.

Accepted Answer

A) True 
 B)False

Question 8

Amplification is simply the process of amplifying the carrier signal to simulate a collision.

Accepted Answer

A) True 
 B)False

Question 9

List the seven factors discussed in this chapter that affect a LAN or WAN design.

Accepted Answer

The seven factors discussed in this chap

Question 10

WAN vendor equipment ranges from banks of dial-up modems to a combination of channel banks and router interfaces.

Accepted Answer

A) True 
 B)False

Question 11

Jamming can be used in either full- or half-duplex mode.

Accepted Answer

A) True 
 B)False

Question 12

Structured wiring requires the ability to isolate servers, but not hosts or other network devices, on their own cable segment.

Accepted Answer

A) True 
 B)False

Question 13

When setting up wireless MANs ____.

Accepted Answer

A) a small MAN ranging to about 300 feet can be set up using 802.11b 
B) you may use a proprietary infrared design 
C) proprietary radio wave options can be used to create MANs up to 30 miles 
D) All of the above. 
A) a small MAN ranging to about 300 feet can be set up using 802.11b 
B) you may use a proprietary infrared design 
C) proprietary radio wave options can be used to create MANs up to 30 miles 
D) All of the above.

Question 14

For a peer-to-peer wireless LAN with 802.11a devices, all stations must be within a mutual range of about 60 feet to communicate with one another.

Accepted Answer

A) True 
 B)False

Question 15

Which is not true?

Accepted Answer

A) As a network administrator, it is important that you work closely with the server administrator when a new network-accessible software application is installed. 
B) Usually, a bus topology enables faster identification of problems than a star topology. 
C) A network design that uses switches and routers is easier to monitor than one that has multiport repeaters. 
D) None of the above. 
A) As a network administrator, it is important that you work closely with the server administrator when a new network-accessible software application is installed. 
B) Usually, a bus topology enables faster identification of problems than a star topology. 
C) A network design that uses switches and routers is easier to monitor than one that has multiport repeaters. 
D) None of the above.

Question 16

If you are replacing thinnet or Category 3 cable with Category 5 cable, you will have to upgrade thinnet NICs in devices with NICs compatible with ____ cable.

Accepted Answer

A) single-mode fiber-optic 
B) coaxial 
C) twisted-pair 
D) multi-mode fiber-optic 
A) single-mode fiber-optic 
B) coaxial 
C) twisted-pair 
D) multi-mode fiber-optic

Question 17

The M in IGMP stands for ____.

Accepted Answer

A) Management 
B) Multicasting 
C) Meshed 
D) Multiple 
A) Management 
B) Multicasting 
C) Meshed 
D) Multiple

Question 18

What is an RFI? When is it used?

Accepted Answer

An RFI, or request for information, is a

Question 19

The maximum cable bend radius for four-pair twisted-pair cable is about ____ times the circumference of the cable.

Accepted Answer

A) two 
B) four 
C) eight 
D) ten 
A) two 
B) four 
C) eight 
D) ten

Question 20

Match between columns
                        Premises: Cable currently recommended for runs between floors.
Standard used when implementing vertical or backbone cabling.
Cable currently recommended for horizontal runs to the desktop.
Standard(s)that define telecommunications rooms.
Standard used when labeling cable.
Cable used in older LANs for horizontal cable runs to the desktop.
Standard used when implementing horizontal wiring.
Standard used to ensure proper grounding of all cable plants.
Cable in older LANs for vertical cable between floors.

Accepted Answer

The Answer of thinnet cable and EIA/TIA-607 standard and EIA/TIA-606 is...

When a device is new to the market, you should purchase it as soon as possible so that it is at the beginning of its EOL cycle.

Bridges cannot route traffic.

When designing your network, you may want to have ____________________ so that traffic is rerouted and users never know when equipment is malfunctioning.

Routers enable you to ____.

If cable installation costs are high because of requirements to remove hazardous materials or because plenum cable is required, consider using ____________________ solutions as an alternative.

RFP stands for ____.

In a building with horizontal wiring, each floor represents a discrete unit of cabling.

Amplification is simply the process of amplifying the carrier signal to simulate a collision.

List the seven factors discussed in this chapter that affect a LAN or WAN design.

WAN vendor equipment ranges from banks of dial-up modems to a combination of channel banks and router interfaces.

Jamming can be used in either full- or half-duplex mode.

Structured wiring requires the ability to isolate servers, but not hosts or other network devices, on their own cable segment.

When setting up wireless MANs ____.

For a peer-to-peer wireless LAN with 802.11a devices, all stations must be within a mutual range of about 60 feet to communicate with one another.

Which is not true?

If you are replacing thinnet or Category 3 cable with Category 5 cable, you will have to upgrade thinnet NICs in devices with NICs compatible with ____ cable.

The M in IGMP stands for ____.

What is an RFI? When is it used?

The maximum cable bend radius for four-pair twisted-pair cable is about ____ times the circumference of the cable.

Lan/Wan Networking: an Overview

Lan/Wan Interconnectivity

Physical Transmission Options

Network Transmission Equipment

Lan Protocols

Tcp/Ip Past, Present, and Future

Wan Transport Methods

ATM Technologies

Wireless Technologies

Integrating Voice, Video, and Data

Filters

Exam 11: Lan and Wan Design: Putting It All Together

When a device is new to the market, you should purchase it as soon as possible so that it is at the beginning of its EOL cycle.

Bridges cannot route traffic.

When designing your network, you may want to have ____________________ so that traffic is rerouted and users never know when equipment is malfunctioning.

Routers enable you to ____.

If cable installation costs are high because of requirements to remove hazardous materials or because plenum cable is required, consider using ____________________ solutions as an alternative.

RFP stands for ____.

In a building with horizontal wiring, each floor represents a discrete unit of cabling.

Amplification is simply the process of amplifying the carrier signal to simulate a collision.

List the seven factors discussed in this chapter that affect a LAN or WAN design.

WAN vendor equipment ranges from banks of dial-up modems to a combination of channel banks and router interfaces.

Jamming can be used in either full- or half-duplex mode.

Structured wiring requires the ability to isolate servers, but not hosts or other network devices, on their own cable segment.

When setting up wireless MANs ____.

For a peer-to-peer wireless LAN with 802.11a devices, all stations must be within a mutual range of about 60 feet to communicate with one another.

Which is not true?

If you are replacing thinnet or Category 3 cable with Category 5 cable, you will have to upgrade thinnet NICs in devices with NICs compatible with ____ cable.

The M in IGMP stands for ____.

What is an RFI? When is it used?

The maximum cable bend radius for four-pair twisted-pair cable is about ____ times the circumference of the cable.

Lan/Wan Networking: an Overview

Lan/Wan Interconnectivity

Physical Transmission Options

Network Transmission Equipment

Lan Protocols

Tcp/Ip Past, Present, and Future

Wan Transport Methods

ATM Technologies

Wireless Technologies

Integrating Voice, Video, and Data

Filters