Question 1

A typical motor size for an electric drill might be __________.

Accepted Answer

A)  2 amps 
B)  13 amps 
C)  60 amps 
D)  100 amps 
A)  2 amps 
B)  13 amps 
C)  60 amps 
D)  100 amps B

Question 2

All corded tools made in the last 15 years will have a polarized plug-where one blade is __________. This design ensures that the plug can only be inserted into the outlet one way to prevent __________.

Accepted Answer

wider than the other; electric shock

Question 3

Explain why the stock being cut off should not be held or supported.

Accepted Answer

The stock being cut off should not be supported as that may cause the blade to bind in the kerf.

Question 4

One of the most popular size circular saw blades is the __________.

Accepted Answer

A)  6 3/4" 
B)  7 1/4" 
C)  9" 
D)  10" 
A)  6 3/4" 
B)  7 1/4" 
C)  9" 
D)  10"

Question 5

When it comes to power tool safety, which is NOT a rule that should be observed at all times?

Accepted Answer

A)  Only plug corded tools into GFCI-protected outlets. 
B)  Tools that are not double-insulated must be connected to an electrical ground. 
C)  Be sure corded and pneumatic tools are plugged in when changing blades, bits, and attachments. 
D)  Use power tools only if you've received instruction in their use. 
A)  Only plug corded tools into GFCI-protected outlets. 
B)  Tools that are not double-insulated must be connected to an electrical ground. 
C)  Be sure corded and pneumatic tools are plugged in when changing blades, bits, and attachments. 
D)  Use power tools only if you've received instruction in their use.

Question 6

To drill holes in wood ranging in size from 3/8" to 2" or more, a __________ bit would be used.

Accepted Answer

A)  twist 
B)  spade 
C)  carbide 
D)  masonry 
A)  twist 
B)  spade 
C)  carbide 
D)  masonry

Question 7

__________ are designed to sense an imbalance in the electrical current flowing in the hot and neutral conductors.

Accepted Answer

The answer of __________ are designed to sense an imbalance...

Question 8

A(n) __________ bearing is a style of bearing in which the moving parts roll on small steel rollers.

Accepted Answer

A)  ball 
B)  sleeve 
C)  oil 
D)  roller 
A)  ball 
B)  sleeve 
C)  oil 
D)  roller

Question 9

When drilling metal, the __________ speed setting on the drill should be used.

Accepted Answer

A)  low 
B)  medium 
C)  medium to fast 
D)  fast 
A)  low 
B)  medium 
C)  medium to fast 
D)  fast

Question 10

When inspecting a circular saw before using it, always check to see that the teeth on the saw blade are pointing ____________________ in the front of the saw.

Accepted Answer

The answer of When inspecting a circular saw before using...

Question 11

A(n) __________ saw is used to make curved cuts and to saw small openings.

Accepted Answer

A)  circular saw 
B)  reciprocating saw 
C)  saber saw 
D)  hack saw 
A)  circular saw 
B)  reciprocating saw 
C)  saber saw 
D)  hack saw

Question 12

On power tools, the part of the tool that rests on the work piece is called the __________.

Accepted Answer

The answer of On power tools, the part of the...

Question 13

To prevent a drill bit from walking out of position, you should use a ______________________________.

Accepted Answer

The answer of To prevent a drill bit from walking...

Question 14

A(n) __________ bearing is a style of bearing in which the moving parts ride on a smooth metal tube.

Accepted Answer

A)  ball 
B)  sleeve 
C)  oil 
D)  roller 
A)  ball 
B)  sleeve 
C)  oil 
D)  roller

Question 15

In 1928, a company named __________ invented the portable circular saw.

Accepted Answer

A)  Black and Decker 
B)  Makita 
C)  DeWalt 
D)  Skil 
A)  Black and Decker 
B)  Makita 
C)  DeWalt 
D)  Skil

Question 16

A variety of __________ saws blades are available for rough cuts in wood, smoother cuts in wood, cutting metal, cutting plastics, and demolition work.

Accepted Answer

A)  Circular 
B)  Reciprocating 
C)  Saber 
D)  Keyhole 
A)  Circular 
B)  Reciprocating 
C)  Saber 
D)  Keyhole

Question 17

Explain why tools that are double insulated do not need to be grounded.

Accepted Answer

Double-insulated tools do not

Question 18

When using a corded drill to drive screws, the screw driver attachment needs to have a __________ to control the amount of torque applied to the screw.

Accepted Answer

The answer of When using a corded drill to drive...

Question 19

Explain why you should never overtighten the nut when installing a new blade on a circular saw.

Accepted Answer

Most saws have a special washe

Question 20

Explain the advantages that cordless tools have over corded power tools.

Accepted Answer

They are more portable and the

Exam 15: Power Tools-Selection, Use, and Care

A typical motor size for an electric drill might be __________.

All corded tools made in the last 15 years will have a polarized plug-where one blade is __________. This design ensures that the plug can only be inserted into the outlet one way to prevent __________.

Explain why the stock being cut off should not be held or supported.

One of the most popular size circular saw blades is the __________.

When it comes to power tool safety, which is NOT a rule that should be observed at all times?

To drill holes in wood ranging in size from 3/8" to 2" or more, a __________ bit would be used.

__________ are designed to sense an imbalance in the electrical current flowing in the hot and neutral conductors.

A(n) __________ bearing is a style of bearing in which the moving parts roll on small steel rollers.

When drilling metal, the __________ speed setting on the drill should be used.

When inspecting a circular saw before using it, always check to see that the teeth on the saw blade are pointing ____________________ in the front of the saw.

A(n) __________ saw is used to make curved cuts and to saw small openings.

On power tools, the part of the tool that rests on the work piece is called the __________.

To prevent a drill bit from walking out of position, you should use a ______________________________.

A(n) __________ bearing is a style of bearing in which the moving parts ride on a smooth metal tube.

In 1928, a company named __________ invented the portable circular saw.

A variety of __________ saws blades are available for rough cuts in wood, smoother cuts in wood, cutting metal, cutting plastics, and demolition work.

Explain why tools that are double insulated do not need to be grounded.

When using a corded drill to drive screws, the screw driver attachment needs to have a __________ to control the amount of torque applied to the screw.

Explain why you should never overtighten the nut when installing a new blade on a circular saw.

Explain the advantages that cordless tools have over corded power tools.

Organization of the Industry

Working in the Industry

Green Construction

Jobsite Safety

Safety With Ladders, Scaffolds, and Machines

Whole Numbers

Decimals

Fractions

Linear Measure

Percent Percentage

Area and Volume

Right Angles

Combined Operations

Hand Tools-Selection, Use and Care

Fasteners

Rigging

Views

Scales

Alphabet of Lines

Use of Symbols

Plan Views

Elevations

Sections and Details

Filters

All corded tools made in the last 15 years will have a polarized plug-where one blade is . This design ensures that the plug can only be inserted into the outlet one way to prevent .