Question 1

During the installation of a small VPLEX Metro, the command 'configuration continue-system-setup' is issued. What is accomplished by this command?

Accepted Answer

A)  Back-end array discovery 
B)  Host initiator discovery 
C)  Second cluster initial setup 
D)  Witness configuration 
A)  Back-end array discovery 
B)  Host initiator discovery 
C)  Second cluster initial setup 
D)  Witness configuration A

Question 2

Refer to the exhibit.   You are planning to perform data mobility between VPLEX Clusters using the GUI. What mobility job options do you have?

Accepted Answer

A)  create, stop, activate, monitor, pause, throttle and terminate 
B)  create, activate, fracture, resync, monitor, pause, and commit 
C)  create, cancel, suspend, monitor, pause, throttle, and terminate 
D)  create, remove, cancel, monitor, pause, throttle, and commit 
A)  create, stop, activate, monitor, pause, throttle and terminate 
B)  create, activate, fracture, resync, monitor, pause, and commit 
C)  create, cancel, suspend, monitor, pause, throttle, and terminate 
D)  create, remove, cancel, monitor, pause, throttle, and commit D

Question 3

A customer has just introduced a new VPLEX cluster into their storage environment with numerous existing storage arrays. They need to present the host's existing data from the VPLEX cluster. Which method would you use to perform this operation?

Accepted Answer

A)  Distribute 
B)  Stripe 
C)  Concatenate 
D)  Encapsulate 
A)  Distribute 
B)  Stripe 
C)  Concatenate 
D)  Encapsulate D

Question 4

What is the purpose of VPLEX Witness in a Metro environment?

Accepted Answer

A)  Observe the state of the clusters, Distinguish link outages, Intercluster failures, Resume or suspend I/O 
B)  Prevent cluster link failure, Stop I/O transfer, Split consistency groups, Failover consistency groups 
C)  Send notifications, Pause I/O transfer, Initiate vault dump, Failover consistency groups 
D)  Observe state of the clusters, Suspend I/O, Execute health-check, Resume I/O 
A)  Observe the state of the clusters, Distinguish link outages, Intercluster failures, Resume or suspend I/O 
B)  Prevent cluster link failure, Stop I/O transfer, Split consistency groups, Failover consistency groups 
C)  Send notifications, Pause I/O transfer, Initiate vault dump, Failover consistency groups 
D)  Observe state of the clusters, Suspend I/O, Execute health-check, Resume I/O

Question 5

A customer has a VPLEX Metro/GEO environment and is requesting that the VPLEX Witness be installed. The requirements for the Witness are: One vCPU
512MB ram
2)5GB storage space
What platform type is supported?

Accepted Answer

A)  64bit ESX4.0 and above 
B)  32/64bit ESXi 5.0 
C)  64bit MS Hyper-V 2012 
D)  VMware Workstation 9.0 and above 
A)  64bit ESX4.0 and above 
B)  32/64bit ESXi 5.0 
C)  64bit MS Hyper-V 2012 
D)  VMware Workstation 9.0 and above

Question 6

What is the purpose of the I/O Module Upgrade Script?

Accepted Answer

A)  To manage the I/O module change during a Metro to Geo topology upgrade. 
B)  To install the I/O load balancer module on the Management Server. 
C)  To configure the GbE I/O modules when installing VPLEX Geo. 
D)  To automate the installation of I/O modules and configuration of the directors. 
A)  To manage the I/O module change during a Metro to Geo topology upgrade. 
B)  To install the I/O load balancer module on the Management Server. 
C)  To configure the GbE I/O modules when installing VPLEX Geo. 
D)  To automate the installation of I/O modules and configuration of the directors.

Question 7

What is required of an ESX host for the Witness to be installed?

Accepted Answer

A)  MAC address change set to Accept 
B)  Promiscuous mode set to Accept 
C)  ESX host in Cluster 1 failure domain 
D)  ESX host in Cluster 2 failure domain 
A)  MAC address change set to Accept 
B)  Promiscuous mode set to Accept 
C)  ESX host in Cluster 1 failure domain 
D)  ESX host in Cluster 2 failure domain

Question 8

After registering Cluster-2 with ESRS during a VPLEX Metro cluster build, what is the next step to perform before the cluster is successfully built?

Accepted Answer

A)  Complete EZ-Setup Wizard on Cluster-1 
B)  Complete EZ-Setup Wizard on Cluster-2 
C)  Configure WAN connections on Cluster-1 
D)  Configure WAN connections on Cluster-2 
A)  Complete EZ-Setup Wizard on Cluster-1 
B)  Complete EZ-Setup Wizard on Cluster-2 
C)  Configure WAN connections on Cluster-1 
D)  Configure WAN connections on Cluster-2

Question 9

What is a key advantage of integrating VPLEX into a VMware environment?

Accepted Answer

A)  If VM data is shared across arrays or across data centers it becomes problematic, VPLEX solves these problems. 
B)  Without VPLEX, Motion can only migrate to other disks within the same array. 
C)  VMware HA can only replicate across data centers to same-type arrays. VPLEX allows data stores to live on any array-type. 
D)  Without VPLEX, all of an ESX server's data must reside on the same array. 
A)  If VM data is shared across arrays or across data centers it becomes problematic, VPLEX solves these problems. 
B)  Without VPLEX, Motion can only migrate to other disks within the same array. 
C)  VMware HA can only replicate across data centers to same-type arrays. VPLEX allows data stores to live on any array-type. 
D)  Without VPLEX, all of an ESX server's data must reside on the same array.

Question 10

Refer to the exhibit.   The customer deleted ext_2 on a 20 GB LUN in order to make an extent of 10 GB. Why is the customer unable to create a 10 GB extent?

Accepted Answer

A)  Storage array must be re-discovered. 
B)  ext_2 cannot be deleted. 
C)  Chunks of the storage need to be contiguous. 
D)  The defrag property is set to false. 
A)  Storage array must be re-discovered. 
B)  ext_2 cannot be deleted. 
C)  Chunks of the storage need to be contiguous. 
D)  The defrag property is set to false.

Question 11

Which VPLEX component is configured with a public IP address during the installation process?

Accepted Answer

A)  LCOM Switch 
B)  Director A 
C)  Management Server 
D)  Director B 
A)  LCOM Switch 
B)  Director A 
C)  Management Server 
D)  Director B

Question 12

How do you verify that the VPLEX upgrade has completed successfully?

Accepted Answer

A)  Log into the VPLEX Unisphere interface. 
B)  Run the cluster-summary command. 
C)  Check that the system LED is green on each director. 
D)  Run the ndu pre-check command. 
A)  Log into the VPLEX Unisphere interface. 
B)  Run the cluster-summary command. 
C)  Check that the system LED is green on each director. 
D)  Run the ndu pre-check command.

Question 13

After registering Cluster-2 with ESRS during a VPLEX Metro cluster build, what is the next step to perform before the cluster is successfully built?

Accepted Answer

A)  Complete EZ-Setup Wizard on Cluster-2 
B)  Configure WAN connections on Cluster-1 
C)  Complete EZ-Setup Wizard on Cluster-1 
D)  Configure WAN connections on Cluster-2 
A)  Complete EZ-Setup Wizard on Cluster-2 
B)  Configure WAN connections on Cluster-1 
C)  Complete EZ-Setup Wizard on Cluster-1 
D)  Configure WAN connections on Cluster-2

Question 14

In a VPLEX Metro with Witness, which command checks the status and uptime of VPN, and returns the remote VPLEX management IP address and the witness public IP address?

Accepted Answer

A)  shell command sudo /usr/sbin/ipsec statusall 
B)  vplexcli command cluster status 
C)  shell command /sbin/ifconfig 
D)  vplexcli command VPlexadmin show 
A)  shell command sudo /usr/sbin/ipsec statusall 
B)  vplexcli command cluster status 
C)  shell command /sbin/ifconfig 
D)  vplexcli command VPlexadmin show

Question 15

A customer has purchased a dual engine VPLEX Metro cluster. During installation, there are not enough free SAN ports to connect all WAN-COM ports to the SAN. What is the recommended approach?

Accepted Answer

A)  The customer must connect the WAN-COM ports of the first engine only and disable the second engine from the VPLEX CLI. 
B)  It is sufficient to connect the WAN-COM ports of either engine 1 or 2 because redundancy is provided by leveraging two separate SAN fabrics. 
C)  The customer must provide additional SAN ports or acquire additional SAN ports to connect all WAN-COM ports of both VPLEX engines to the SAN. 
D)  The customer must connect the WAN-COM ports of the first engine only and disable the second engine from the Unisphere for VPLEX GUI. 
A)  The customer must connect the WAN-COM ports of the first engine only and disable the second engine from the VPLEX CLI. 
B)  It is sufficient to connect the WAN-COM ports of either engine 1 or 2 because redundancy is provided by leveraging two separate SAN fabrics. 
C)  The customer must provide additional SAN ports or acquire additional SAN ports to connect all WAN-COM ports of both VPLEX engines to the SAN. 
D)  The customer must connect the WAN-COM ports of the first engine only and disable the second engine from the Unisphere for VPLEX GUI.

Question 16

In addition to Active Directory, with what other directory service can VPLEX integrate for user authentication?

Accepted Answer

A)  LDAP 
B)  NIS 
C)  NDS 
D)  PAM 
A)  LDAP 
B)  NIS 
C)  NDS 
D)  PAM

Question 17

What function does the SNMP agent on the Management Server provide?

Accepted Answer

A)  Cluster Management 
B)  Director Management 
C)  Cluster Statistics 
D)  User Management 
A)  Cluster Management 
B)  Director Management 
C)  Cluster Statistics 
D)  User Management

Question 18

You have a perpetual performance monitor running on director 1-1-A The data being monitored is growing at a rate of 2 MB per minute. At the current data rate, how far back in time will this monitor be able to reach?

Accepted Answer

A)  5 minutes 
B)  5 hours 
C)  50 hours 
D)  50 minutes 
A)  5 minutes 
B)  5 hours 
C)  50 hours 
D)  50 minutes

Question 19

How can you throttle the migration rate for VPLEX?

Accepted Answer

A)  By configuring the maximum copy speed 
B)  By setting the copy policy 
C)  This is done automatically without any user action 
D)  By dynamically changing the I/O write size for copying 
A)  By configuring the maximum copy speed 
B)  By setting the copy policy 
C)  This is done automatically without any user action 
D)  By dynamically changing the I/O write size for copying

Question 20

Which command would you execute to perform basic system checks to ensure that the VPLEX cluster is working properly?

Accepted Answer

A)  health-check 
B)  cluster config-dump 
C)  validate-system-configuration 
D)  cluster summary 
A)  health-check 
B)  cluster config-dump 
C)  validate-system-configuration 
D)  cluster summary

During the installation of a small VPLEX Metro, the command 'configuration continue-system-setup' is issued. What is accomplished by this command?

Refer to the exhibit. You are planning to perform data mobility between VPLEX Clusters using the GUI. What mobility job options do you have?

A customer has just introduced a new VPLEX cluster into their storage environment with numerous existing storage arrays. They need to present the host's existing data from the VPLEX cluster. Which method would you use to perform this operation?

What is the purpose of VPLEX Witness in a Metro environment?

A customer has a VPLEX Metro/GEO environment and is requesting that the VPLEX Witness be installed. The requirements for the Witness are: One vCPU 512MB ram 2)5GB storage space What platform type is supported?

What is the purpose of the I/O Module Upgrade Script?

What is required of an ESX host for the Witness to be installed?

After registering Cluster-2 with ESRS during a VPLEX Metro cluster build, what is the next step to perform before the cluster is successfully built?

What is a key advantage of integrating VPLEX into a VMware environment?

Refer to the exhibit. The customer deleted ext_2 on a 20 GB LUN in order to make an extent of 10 GB. Why is the customer unable to create a 10 GB extent?

Which VPLEX component is configured with a public IP address during the installation process?

How do you verify that the VPLEX upgrade has completed successfully?

After registering Cluster-2 with ESRS during a VPLEX Metro cluster build, what is the next step to perform before the cluster is successfully built?

In a VPLEX Metro with Witness, which command checks the status and uptime of VPN, and returns the remote VPLEX management IP address and the witness public IP address?

A customer has purchased a dual engine VPLEX Metro cluster. During installation, there are not enough free SAN ports to connect all WAN-COM ports to the SAN. What is the recommended approach?

In addition to Active Directory, with what other directory service can VPLEX integrate for user authentication?

What function does the SNMP agent on the Management Server provide?

You have a perpetual performance monitor running on director 1-1-A The data being monitored is growing at a rate of 2 MB per minute. At the current data rate, how far back in time will this monitor be able to reach?

How can you throttle the migration rate for VPLEX?

Which command would you execute to perform basic system checks to ensure that the VPLEX cluster is working properly?

XtremIO Solutions Specialist Exam for Implementation Engineers

RecoverPoint Specialist for Implementation Engineers

Unity Solutions Specialist Exam for Implementation Engineers

XtremIO Solutions and Design Specialist Exam for Technology Architects

Isilon Solutions and Design Specialist for Technology Architects

VPLEX Specialist Exam for Storage Administrators

RecoverPoint Specialist for Storage Administrators

Backup and Recovery - Avamar Specialist for Implementation Engineers

Backup Recovery - Avamar Specialist for Storage Administrators

ScaleIO 1.x Server-Based SAN

Filters

Exam 1: VPLEX Specialist for Implementation Engineers

During the installation of a small VPLEX Metro, the command 'configuration continue-system-setup' is issued. What is accomplished by this command?

Refer to the exhibit. You are planning to perform data mobility between VPLEX Clusters using the GUI. What mobility job options do you have?

A customer has just introduced a new VPLEX cluster into their storage environment with numerous existing storage arrays. They need to present the host's existing data from the VPLEX cluster. Which method would you use to perform this operation?

What is the purpose of VPLEX Witness in a Metro environment?

A customer has a VPLEX Metro/GEO environment and is requesting that the VPLEX Witness be installed. The requirements for the Witness are: One vCPU 512MB ram 2)5GB storage space What platform type is supported?

What is the purpose of the I/O Module Upgrade Script?

What is required of an ESX host for the Witness to be installed?

After registering Cluster-2 with ESRS during a VPLEX Metro cluster build, what is the next step to perform before the cluster is successfully built?

What is a key advantage of integrating VPLEX into a VMware environment?

Refer to the exhibit. The customer deleted ext_2 on a 20 GB LUN in order to make an extent of 10 GB. Why is the customer unable to create a 10 GB extent?

Which VPLEX component is configured with a public IP address during the installation process?

How do you verify that the VPLEX upgrade has completed successfully?

After registering Cluster-2 with ESRS during a VPLEX Metro cluster build, what is the next step to perform before the cluster is successfully built?

In a VPLEX Metro with Witness, which command checks the status and uptime of VPN, and returns the remote VPLEX management IP address and the witness public IP address?

A customer has purchased a dual engine VPLEX Metro cluster. During installation, there are not enough free SAN ports to connect all WAN-COM ports to the SAN. What is the recommended approach?

In addition to Active Directory, with what other directory service can VPLEX integrate for user authentication?

What function does the SNMP agent on the Management Server provide?

You have a perpetual performance monitor running on director 1-1-A The data being monitored is growing at a rate of 2 MB per minute. At the current data rate, how far back in time will this monitor be able to reach?

How can you throttle the migration rate for VPLEX?

Which command would you execute to perform basic system checks to ensure that the VPLEX cluster is working properly?

XtremIO Solutions Specialist Exam for Implementation Engineers

RecoverPoint Specialist for Implementation Engineers

Unity Solutions Specialist Exam for Implementation Engineers

XtremIO Solutions and Design Specialist Exam for Technology Architects

Isilon Solutions and Design Specialist for Technology Architects

VPLEX Specialist Exam for Storage Administrators

RecoverPoint Specialist for Storage Administrators

Backup and Recovery - Avamar Specialist for Implementation Engineers

Backup Recovery - Avamar Specialist for Storage Administrators

ScaleIO 1.x Server-Based SAN

Filters