Exam 2: Solidstate Devices in Industrial Applications, Operational Amplifiers and Linear ICS

If the transistor is in a socket, the first step in troubleshooting is to remove it and use and ohmmeter or plug it into a curve tracer.

(True/False)

4.9/5

(38)

Question 41

-The symbol in this graphic is a

(Multiple Choice)

4.8/5

(32)

Question 42

When an op amp is used as a current -to -voltage converter, the load is connected in the feedback loop and the input signal is connected to the inverting input.

(True/False)

4.9/5

(40)

Question 43

The characteristic curves of a bipolar junction transistor depict a series of collector currents for a range of collector -emitter voltages.

(True/False)

4.9/5

(36)

Question 44

In a shunt regulator the transistor is in series with the load.

(True/False)

4.8/5

(30)

Question 45

Input bias current of an op amp is the sum of the two input bias currents when the output is zero.

(True/False)

4.9/5

(42)

Question 46

The discrete implementation amplifier can provide higher bandwidths than the monolithic implementation amplifier.

(True/False)

4.9/5

(45)

Question 47

Instrumentation amplifiers accurately output the difference between the inputs providing common -mode rejection.

(True/False)

4.9/5

(37)

Question 48

The current that flows when a transistor is cut off is called

(Multiple Choice)

4.8/5

(36)

Question 49

For a transistor operating in the active region, it's not quite in saturation, and its collector current is equal to the base current times the gain.

(True/False)

4.8/5

(32)

Question 50

When an op amp is used as a voltage -to -current converter, the load is connected in the feedback loop and the input signal is connected to the non -inverting input.

(True/False)

4.9/5

(34)

Question 51

Which of the following op amp configurations has the highest input resistance?

(Multiple Choice)

5.0/5

(29)

Question 52

A notch filter is another term for a band -pass filter.

(True/False)

5.0/5

(43)

Question 53

When designing an inverting op amp circuit, the output offset phenomenon can be mitigated by_________

(Multiple Choice)

4.8/5

(37)

Question 54

Op amp characteristics can be tailored to fit a specific application by changing a few components.

(True/False)

4.9/5

(35)

Question 55

‪ -Examine these waveforms. The most accurate description the circuit that has the V_OUTfor the V_IN would be a __________ op amp.

(Multiple Choice)

4.8/5

(50)

Question 56

When reversed biased, the light emitting diode behaves like any other diode.

(True/False)

4.9/5

(42)

Question 57

The best circuit choice for rejecting the common -mode DC component on which a signal is riding is a

(Multiple Choice)

4.8/5

(35)

Question 58

The boost converter has a higher efficiency than the buck converter.

(True/False)

4.8/5

(41)

Question 59

Match the components with their function -R3 and R4

(Multiple Choice)

4.8/5

(31)

Question 60

Showing 41 - 60 of 79

If the transistor is in a socket, the first step in troubleshooting is to remove it and use and ohmmeter or plug it into a curve tracer.

-The symbol in this graphic is a

When an op amp is used as a current -to -voltage converter, the load is connected in the feedback loop and the input signal is connected to the inverting input.

The characteristic curves of a bipolar junction transistor depict a series of collector currents for a range of collector -emitter voltages.

In a shunt regulator the transistor is in series with the load.

Input bias current of an op amp is the sum of the two input bias currents when the output is zero.

The discrete implementation amplifier can provide higher bandwidths than the monolithic implementation amplifier.

Instrumentation amplifiers accurately output the difference between the inputs providing common -mode rejection.

The current that flows when a transistor is cut off is called

For a transistor operating in the active region, it's not quite in saturation, and its collector current is equal to the base current times the gain.

When an op amp is used as a voltage -to -current converter, the load is connected in the feedback loop and the input signal is connected to the non -inverting input.

Which of the following op amp configurations has the highest input resistance?

A notch filter is another term for a band -pass filter.

When designing an inverting op amp circuit, the output offset phenomenon can be mitigated by_________

Op amp characteristics can be tailored to fit a specific application by changing a few components.

‪ -Examine these waveforms. The most accurate description the circuit that has the V_OUTfor the V_IN would be a __________ op amp.

When reversed biased, the light emitting diode behaves like any other diode.

The best circuit choice for rejecting the common -mode DC component on which a signal is riding is a

The boost converter has a higher efficiency than the buck converter.

Match the components with their function -R3 and R4

Introduction to Industrial Control Systems, Discrete Control Input and Output Devices

SCRS, Triacs, Other Thryristors, Discrete Automation Sensors and Devices

Analog Processes Control Devices, Sensors and Safety

DC Motors, Control Circuits, AC Motors and Variable Speed Drives

Special Purpose Motor, Control Devices and Programmable Logic Controllers

Embedded Microcontrollers, Open and Closed Loop Process Control

Industrial Robots, Automation Systems and Data Communication Between Intelligent Machines

Filters

Exam 2: Solidstate Devices in Industrial Applications, Operational Amplifiers and Linear ICS

If the transistor is in a socket, the first step in troubleshooting is to remove it and use and ohmmeter or plug it into a curve tracer.

-The symbol in this graphic is a

When an op amp is used as a current -to -voltage converter, the load is connected in the feedback loop and the input signal is connected to the inverting input.

The characteristic curves of a bipolar junction transistor depict a series of collector currents for a range of collector -emitter voltages.

In a shunt regulator the transistor is in series with the load.

Input bias current of an op amp is the sum of the two input bias currents when the output is zero.

The discrete implementation amplifier can provide higher bandwidths than the monolithic implementation amplifier.

Instrumentation amplifiers accurately output the difference between the inputs providing common -mode rejection.

The current that flows when a transistor is cut off is called

For a transistor operating in the active region, it's not quite in saturation, and its collector current is equal to the base current times the gain.

When an op amp is used as a voltage -to -current converter, the load is connected in the feedback loop and the input signal is connected to the non -inverting input.

Which of the following op amp configurations has the highest input resistance?

A notch filter is another term for a band -pass filter.

When designing an inverting op amp circuit, the output offset phenomenon can be mitigated by_________

Op amp characteristics can be tailored to fit a specific application by changing a few components.

‪ -Examine these waveforms. The most accurate description the circuit that has the VOUT for the VIN would be a __________ op amp.

When reversed biased, the light emitting diode behaves like any other diode.

The best circuit choice for rejecting the common -mode DC component on which a signal is riding is a

The boost converter has a higher efficiency than the buck converter.

Match the components with their function -R3 and R4

Introduction to Industrial Control Systems, Discrete Control Input and Output Devices

SCRS, Triacs, Other Thryristors, Discrete Automation Sensors and Devices

Analog Processes Control Devices, Sensors and Safety

DC Motors, Control Circuits, AC Motors and Variable Speed Drives

Special Purpose Motor, Control Devices and Programmable Logic Controllers

Embedded Microcontrollers, Open and Closed Loop Process Control

Industrial Robots, Automation Systems and Data Communication Between Intelligent Machines

Filters

‪ -Examine these waveforms. The most accurate description the circuit that has the V_OUTfor the V_IN would be a __________ op amp.