Question 1

RIP routing has been enabled on the router.Which command is issued to use RIP routing to a host computer with an IP address of 192.168.20.3?

Accepted Answer

A) router(config-router-rip)# network 192.168.20.0 
B) router(config-router)# network 192.168.20.0 
C) router(config)# network 192.168.20.0 
D) router(config-router)# network 192.168.20.3 
E) router(config)# network 192.168.20.3 
A) router(config-router-rip)# network 192.168.20.0 
B) router(config-router)# network 192.168.20.0 
C) router(config)# network 192.168.20.0 
D) router(config-router)# network 192.168.20.3 
E) router(config)# network 192.168.20.3 B

Question 2

Which of the following best characterizes OSPF's Area 0?

Accepted Answer

A) Used to hide data packets 
B) Root or the backbone for the network 
C) Inverse mask bits 
D) Route selection bits 
A) Used to hide data packets 
B) Root or the backbone for the network 
C) Inverse mask bits 
D) Route selection bits B

Question 3

What is the administrative distance for a directly connected route in Cisco networking?

Accepted Answer

A) 1 
B) 0 
C) 10 
D) 20 
A) 1 
B) 0 
C) 10 
D) 20 B

Question 4

A computer with an IP address of 10.10.5.1 sends a data packet with a destination IP address of 10.5.10.20 using a subnet mask of 255.255.255.0.The packet stays in the LAN.True or False?

Accepted Answer

A) True 
 B)False

Question 5

What command will provide information about the dynamic routing protocols on your Cisco router and their configurations?

Accepted Answer

A) show protocol 
B) show ip protocol 
C) show protocol dynamic 
D) show protocol link-state 
A) show protocol 
B) show ip protocol 
C) show protocol dynamic 
D) show protocol link-state

Question 6

Which of the following is not an advantage of OSPF?

Accepted Answer

A) It's very easy to implement. 
B) It uses VLSM. 
C) Link-state changes are immediately reported. 
D) It's not a proprietary protocol. 
A) It's very easy to implement. 
B) It uses VLSM. 
C) Link-state changes are immediately reported. 
D) It's not a proprietary protocol.

Question 7

What is the administrative distance of the RIP routing protocol?

Accepted Answer

A) 120 
B) 1 
C) 90 
D) 110 
E) 100 
A) 120 
B) 1 
C) 90 
D) 110 
E) 100

Question 8

You want to configure OSPF on five interfaces all in the 10.X.X.X network range using a single command.What command does this?

Accepted Answer

A) network 10.0.0.0 255.0.0.0 area 0 
B) network 10.0.0.0 0.255.255.255 area 0 
C) network 10.0.0.0 255.255.255.0 area 0 
D) network 10.0.0.0 255.255.255.255 area 0 
A) network 10.0.0.0 255.0.0.0 area 0 
B) network 10.0.0.0 0.255.255.255 area 0 
C) network 10.0.0.0 255.255.255.0 area 0 
D) network 10.0.0.0 255.255.255.255 area 0

Question 9

Which of the following does the OSPF routing protocol use to verify that a link between to routers is active and the routers are communicating?

Accepted Answer

A) LSAs 
B) ARP messages 
C) Ping 
D) "Hello" packets 
A) LSAs 
B) ARP messages 
C) Ping 
D) "Hello" packets

Question 10

What command would you use to verify that the OSPF routes you expect are in the routing table?

Accepted Answer

A) show ip route dynamic 
B) show route 
C) show ip route ospf 
D) show ip route dynamic ospf 
A) show ip route dynamic 
B) show route 
C) show ip route ospf 
D) show ip route dynamic ospf

Question 11

Which of the following commands enables you to view the route codes and routes?

Accepted Answer

A) show ip router 
B) show ip route 
C) show routes 
D) show static routes 
A) show ip router 
B) show ip route 
C) show routes 
D) show static routes

Question 12

From which prompt is the command to specify RIP routing issued?

Accepted Answer

A) Router(config) 
B) Router(config)> 
C) Router(config)# 
D) Router(config-router-rip)# 
A) Router(config) 
B) Router(config)> 
C) Router(config)# 
D) Router(config-router-rip)#

Question 13

Which of the following best characterizes areas in the OSPF protocol?

Accepted Answer

A) Not used 
B) Used to partition a large network into small networks 
C) Used to combine small networks into one large network 
D) An inefficient use of bandwidth 
A) Not used 
B) Used to partition a large network into small networks 
C) Used to combine small networks into one large network 
D) An inefficient use of bandwidth

Question 14

Which of the following router commands could be used to display the routing protocol configured on the router?

Accepted Answer

A) router>sh ip protocol detail 
B) router# sh ip protocol 
C) router# sh protocol 
D) All of these answers are correct 
A) router>sh ip protocol detail 
B) router# sh ip protocol 
C) router# sh protocol 
D) All of these answers are correct

Question 15

After issuing the proper command to configure a static route,the prompt does which of the following?

Accepted Answer

A) Changes to router (config-static)# 
B) Changes to router(config-static) 
C) Does not change; remains at router (config#) 
D) Does not change; remains at router (config)# 
A) Changes to router (config-static)# 
B) Changes to router(config-static) 
C) Does not change; remains at router (config#) 
D) Does not change; remains at router (config)#

Question 16

Advertising a network means the routing table containing the network is shared with its neighbor routers.True or False?

Accepted Answer

A) True 
 B)False

Question 17

What is the administrative distance for RIP in Cisco networking?

Accepted Answer

A) 10 
B) 90 
C) 110 
D) 120 
A) 10 
B) 90 
C) 110 
D) 120

Question 18

Which of the following commands displays the router's running-configuration?

Accepted Answer

A) router> show ip running-configuration 
B) router# show rip running-configuration 
C) router# show running-configuration 
D) router# show configuration 
A) router> show ip running-configuration 
B) router# show rip running-configuration 
C) router# show running-configuration 
D) router# show configuration

Question 19

Which prompt is displayed after issuing the command to enable RIP routing?

Accepted Answer

A) router(config-router-rip)# 
B) router(config-router) 
C) router#(config-router) 
D) router(config-router)# 
E) router#(config-router-rip) 
A) router(config-router-rip)# 
B) router(config-router) 
C) router#(config-router) 
D) router(config-router)# 
E) router#(config-router-rip)

Question 20

Which of the following commands can be used to display the routes configured on the router?

Accepted Answer

A) router> show route 
B) router# show route 
C) router# show rip route 
D) router# show ip route 
A) router> show route 
B) router# show route 
C) router# show rip route 
D) router# show ip route

RIP routing has been enabled on the router.Which command is issued to use RIP routing to a host computer with an IP address of 192.168.20.3?

Which of the following best characterizes OSPF's Area 0?

What is the administrative distance for a directly connected route in Cisco networking?

A computer with an IP address of 10.10.5.1 sends a data packet with a destination IP address of 10.5.10.20 using a subnet mask of 255.255.255.0.The packet stays in the LAN.True or False?

What command will provide information about the dynamic routing protocols on your Cisco router and their configurations?

Which of the following is not an advantage of OSPF?

What is the administrative distance of the RIP routing protocol?

You want to configure OSPF on five interfaces all in the 10.X.X.X network range using a single command.What command does this?

Which of the following does the OSPF routing protocol use to verify that a link between to routers is active and the routers are communicating?

What command would you use to verify that the OSPF routes you expect are in the routing table?

Which of the following commands enables you to view the route codes and routes?

From which prompt is the command to specify RIP routing issued?

Which of the following best characterizes areas in the OSPF protocol?

Which of the following router commands could be used to display the routing protocol configured on the router?

After issuing the proper command to configure a static route,the prompt does which of the following?

Advertising a network means the routing table containing the network is shared with its neighbor routers.True or False?

What is the administrative distance for RIP in Cisco networking?

Which of the following commands displays the router's running-configuration?

Which prompt is displayed after issuing the command to enable RIP routing?

Which of the following commands can be used to display the routes configured on the router?

Introduction to Computer Networks

Physical Layer Cabling: Twisted Pair

Physical Layer Cabling: Fiber Optics

Wireless Networking

Interconnecting the Lans

TCP-IP

Introduction to Router Configuration

Introduction to Switch Configuration

Internet Technologies: Out to the Internet

Troubleshooting

Network Security

Cloud Computing and Virtualization

Codes and Standards

Filters

Exam 9: Routing Protocols

RIP routing has been enabled on the router.Which command is issued to use RIP routing to a host computer with an IP address of 192.168.20.3?

Which of the following best characterizes OSPF's Area 0?

What is the administrative distance for a directly connected route in Cisco networking?

A computer with an IP address of 10.10.5.1 sends a data packet with a destination IP address of 10.5.10.20 using a subnet mask of 255.255.255.0.The packet stays in the LAN.True or False?

What command will provide information about the dynamic routing protocols on your Cisco router and their configurations?

Which of the following is not an advantage of OSPF?

What is the administrative distance of the RIP routing protocol?

You want to configure OSPF on five interfaces all in the 10.X.X.X network range using a single command.What command does this?

Which of the following does the OSPF routing protocol use to verify that a link between to routers is active and the routers are communicating?

What command would you use to verify that the OSPF routes you expect are in the routing table?

Which of the following commands enables you to view the route codes and routes?

From which prompt is the command to specify RIP routing issued?

Which of the following best characterizes areas in the OSPF protocol?

Which of the following router commands could be used to display the routing protocol configured on the router?

After issuing the proper command to configure a static route,the prompt does which of the following?

Advertising a network means the routing table containing the network is shared with its neighbor routers.True or False?

What is the administrative distance for RIP in Cisco networking?

Which of the following commands displays the router's running-configuration?

Which prompt is displayed after issuing the command to enable RIP routing?

Which of the following commands can be used to display the routes configured on the router?

Introduction to Computer Networks

Physical Layer Cabling: Twisted Pair

Physical Layer Cabling: Fiber Optics

Wireless Networking

Interconnecting the Lans

TCP-IP

Introduction to Router Configuration

Introduction to Switch Configuration

Internet Technologies: Out to the Internet

Troubleshooting

Network Security

Cloud Computing and Virtualization

Codes and Standards

Filters