Question 1

The command to enter the router's global configuration mode is which of the following?

Accepted Answer

A) router> conf t 
B) router> configure t 
C) router(conf t)# 
D) router# conf t 
A) router> conf t 
B) router> configure t 
C) router(conf t)# 
D) router# conf t

Question 2

What is the purpose of administrative distance?

Accepted Answer

A) To provide a metric for a single routing protocol 
B) To provide a preferred route when there are multiple routes to a destination from different protocols 
C) To provide an indication of configuration complexity 
D) To eliminate load balancing for a single routing protocol 
A) To provide a metric for a single routing protocol 
B) To provide a preferred route when there are multiple routes to a destination from different protocols 
C) To provide an indication of configuration complexity 
D) To eliminate load balancing for a single routing protocol

Question 3

All subnets that are attached to Router2 for the network shown in the following figure are:
10.20.100.0
10.50.10.0
   True or False?

Accepted Answer

A) True 
 B)False

Question 4

Which is the router command used to copy the running-configuration to NVRAM?

Accepted Answer

A) copy run tftp 
B) copy run start 
C) copy run flash 
D) copy run show 
A) copy run tftp 
B) copy run start 
C) copy run flash 
D) copy run show

Question 5

A static route is entered from which command prompt? (Select one.)

Accepted Answer

A) router(config)# 
B) router(config#) 
C) router# 
D) router> 
E) router(config-static)# 
A) router(config)# 
B) router(config#) 
C) router# 
D) router> 
E) router(config-static)#

Question 6

You want to configure EIGRP on five interfaces all in the 10.X.X.X network range using a single command.What command does this?

Accepted Answer

A) network 10.0.0.0 
B) network 10.0.0.0 255.0.0.0 
C) network 10.0.0.0 0.255.255.255 area 0 
D) network 10.0.0.0 mask 255.0.0.0 
A) network 10.0.0.0 
B) network 10.0.0.0 255.0.0.0 
C) network 10.0.0.0 0.255.255.255 area 0 
D) network 10.0.0.0 mask 255.0.0.0

Question 7

Which of the following is the command for saving the router's running configuration to nonvolatile memory? (Select one.)

Accepted Answer

A) copy run flash 
B) copy run start 
C) copy start flash 
D) copy running flash 
A) copy run flash 
B) copy run start 
C) copy start flash 
D) copy running flash

Question 8

What is the purpose of variable length subnet masks?

Accepted Answer

A) They are not recommended in modern computer networks. 
B) They minimize wasted IP address space when interconnecting subnets. 
C) They reduce the number of bits required in a subnet mask from 32 to 24. 
D) They are the same as classful addressing. 
A) They are not recommended in modern computer networks. 
B) They minimize wasted IP address space when interconnecting subnets. 
C) They reduce the number of bits required in a subnet mask from 32 to 24. 
D) They are the same as classful addressing.

Question 9

What is the administrative distance of a static route?

Accepted Answer

A) 110 
B) 120 
C) 1 
D) 90 
E) 100 
A) 110 
B) 120 
C) 1 
D) 90 
E) 100

Question 10

What is the administrative distance for EIGRP in Cisco networking?

Accepted Answer

A) 10 
B) 90 
C) 110 
D) 120 
A) 10 
B) 90 
C) 110 
D) 120

Question 11

What is the number 10 in the command router ospf 10?

Accepted Answer

A) Tag 
B) Process ID 
C) AS number 
D) Metric 
A) Tag 
B) Process ID 
C) AS number 
D) Metric

Question 12

What is the administrative distance for OSPF in Cisco networking?

Accepted Answer

A) 10 
B) 90 
C) 110 
D) 120 
A) 10 
B) 90 
C) 110 
D) 120

Question 13

What mode are you in when you use the network command to configure OSPF?

Accepted Answer

A) (config) 
B) (config-if) 
C) (config-router) 
D) (config-ospf) 
A) (config) 
B) (config-if) 
C) (config-router) 
D) (config-ospf)

Question 14

What is the administrative distance for a static route in Cisco networking?

Accepted Answer

A) 1 
B) 0 
C) 10 
D) 20 
A) 1 
B) 0 
C) 10 
D) 20

Question 15

Which of the following commands would you enter to display only the static routes?

Accepted Answer

A) show routes static 
B) show route static 
C) show static ip route 
D) show ip route static 
A) show routes static 
B) show route static 
C) show static ip route 
D) show ip route static

Question 16

Which router command can be used to check whether the router interfaces are properly configured?

Accepted Answer

A) router# show ip interface brief 
B) router> show interface ip brief 
C) router(config)# show ip interface brief 
D) router(config-router)# show interface ip brief 
A) router# show ip interface brief 
B) router> show interface ip brief 
C) router(config)# show ip interface brief 
D) router(config-router)# show interface ip brief

Question 17

Select the command that can be used to route a data packet route out of your current LAN if a route to the specified destination has not been entered into the router's routing table.The destination IP address is 192.168.12.3.The subnet mask being used for the LAN is /26.The next hop IP address is 192.168.12.66.

Accepted Answer

A) router(config)# ip route 0.0.0.0 0.0.0.0 192.168.12.66 
B) router(config)# ip route 192.168.12.66 0.0.0.0 0.0.0.0 
C) router>ip route 0.0.0.0 0.0.0.0 192.168.12.66 
D) router>ip route 192.168.12.66 0.0.0.0 0.0.0.0 
A) router(config)# ip route 0.0.0.0 0.0.0.0 192.168.12.66 
B) router(config)# ip route 192.168.12.66 0.0.0.0 0.0.0.0 
C) router>ip route 0.0.0.0 0.0.0.0 192.168.12.66 
D) router>ip route 192.168.12.66 0.0.0.0 0.0.0.0

Question 18

What is the number 150 in the command router eigrp 150?

Accepted Answer

A) A process ID 
B) An autonomous system number 
C) A metric 
D) A tag 
A) A process ID 
B) An autonomous system number 
C) A metric 
D) A tag

The command to enter the router's global configuration mode is which of the following?

What is the purpose of administrative distance?

All subnets that are attached to Router2 for the network shown in the following figure are: 10.20.100.0 10.50.10.0 True or False?

Which is the router command used to copy the running-configuration to NVRAM?

A static route is entered from which command prompt? (Select one.)

You want to configure EIGRP on five interfaces all in the 10.X.X.X network range using a single command.What command does this?

Which of the following is the command for saving the router's running configuration to nonvolatile memory? (Select one.)

What is the purpose of variable length subnet masks?

What is the administrative distance of a static route?

What is the administrative distance for EIGRP in Cisco networking?

What is the number 10 in the command router ospf 10?

What is the administrative distance for OSPF in Cisco networking?

What mode are you in when you use the network command to configure OSPF?

What is the administrative distance for a static route in Cisco networking?

Which of the following commands would you enter to display only the static routes?

Which router command can be used to check whether the router interfaces are properly configured?

What is the number 150 in the command router eigrp 150?

Introduction to Computer Networks

Physical Layer Cabling: Twisted Pair

Physical Layer Cabling: Fiber Optics

Wireless Networking

Interconnecting the Lans

TCP-IP

Introduction to Router Configuration

Introduction to Switch Configuration

Internet Technologies: Out to the Internet

Troubleshooting

Network Security

Cloud Computing and Virtualization

Codes and Standards

Filters

Exam 9: Routing Protocols

The command to enter the router's global configuration mode is which of the following?

What is the purpose of administrative distance?

All subnets that are attached to Router2 for the network shown in the following figure are: 10.20.100.0 10.50.10.0 True or False?

Which is the router command used to copy the running-configuration to NVRAM?

A static route is entered from which command prompt? (Select one.)

You want to configure EIGRP on five interfaces all in the 10.X.X.X network range using a single command.What command does this?

Which of the following is the command for saving the router's running configuration to nonvolatile memory? (Select one.)

What is the purpose of variable length subnet masks?

What is the administrative distance of a static route?

What is the administrative distance for EIGRP in Cisco networking?

What is the number 10 in the command router ospf 10?

What is the administrative distance for OSPF in Cisco networking?

What mode are you in when you use the network command to configure OSPF?

What is the administrative distance for a static route in Cisco networking?

Which of the following commands would you enter to display only the static routes?

Which router command can be used to check whether the router interfaces are properly configured?

What is the number 150 in the command router eigrp 150?

Introduction to Computer Networks

Physical Layer Cabling: Twisted Pair

Physical Layer Cabling: Fiber Optics

Wireless Networking

Interconnecting the Lans

TCP-IP

Introduction to Router Configuration

Introduction to Switch Configuration

Internet Technologies: Out to the Internet

Troubleshooting

Network Security

Cloud Computing and Virtualization

Codes and Standards

Filters