Question 1

A computer's default gateway setting is the MAC address of a router on a remote network.

Accepted Answer

A) True 
 B)False

Question 2

Match each item with a statement below.
a.switch
b.default route
c.half-duplex mode
d.router
e.bandwidth sharing
f.repeater
g.CTS
h.network interface card
i.uplink port
j.network bandwidth
-designated port on a hub or switch used to connect to another hub or switch

Accepted Answer

The answer of Match each item with a statement below.
a.switch
b.default...

Question 3

The network ____________ is a measurement of the amount of data that can pass through a network in a certain period of time.

Accepted Answer

The answer of The network ____________ is a measurement of...

Question 4

What command would you issue from the command prompt to test whether your computer has connectivity to the network?

Accepted Answer

A)  ping IPaddress 
B)  arp -d IPaddress 
C)  ipconfig IPaddress 
D)  ipconfig /all

Question 5

A wireless access point is most like which other network device, in that all computers send signals through it to communicate with other computers?

Accepted Answer

A)  switch 
B)  router 
C)  hub 
D)  modem

Question 6

A switch operating in full ___________ mode can send and receive data at the same time.

Accepted Answer

The answer of A switch operating in full ___________ mode...

Question 7

Match each item with a statement below.
a.switch
b.default route
c.half-duplex mode
d.router
e.bandwidth sharing
f.repeater
g.CTS
h.network interface card
i.uplink port
j.network bandwidth
-amount of data that can be transferred on a network in a specified interval

Accepted Answer

The answer of Match each item with a statement below.
a.switch
b.default...

Question 8

What component of the computer contains a MAC address?

Accepted Answer

A)  motherboard 
B)  NIC 
C)  CPU 
D)  BIOS

Question 9

What is the MAC address of a computer?

Accepted Answer

The answer of What is the MAC address of a...

Question 10

Match each item with a statement below.
a.switch
b.default route
c.half-duplex mode
d.router
e.bandwidth sharing
f.repeater
g.CTS
h.network interface card
i.uplink port
j.network bandwidth
-device that uses MAC addresses to determine the destination of frame

Accepted Answer

The answer of Match each item with a statement below.
a.switch
b.default...

Question 11

When a NIC is in promiscuous mode, it will process only the frames in which the destination MAC address matches its own MAC address.

Accepted Answer

A) True 
 B)False

Question 12

Match each item with a statement below.
a.switch
b.default route
c.half-duplex mode
d.router
e.bandwidth sharing
f.repeater
g.CTS
h.network interface card
i.uplink port
j.network bandwidth
-device that only regenerates incoming signals

Accepted Answer

The answer of Match each item with a statement below.
a.switch
b.default...

Question 13

In a computer's IP address settings, the default _____________ is the address of the router to which a computer sends all packets that are intended for networks outside of its own.

Accepted Answer

The answer of In a computer's IP address settings, the...

Question 14

Just as a switch keeps records of MAC addresses that it has learned, so does your computer. What protocol does your computer use to learn MAC addresses?

Accepted Answer

A)  ARP 
B)  ICMP 
C)  DHCP 
D)  IP

Question 15

When referring to network bandwidth, what is the basic unit of measurement?

Accepted Answer

A)  bytes per second 
B)  bits per second 
C)  bandwidth per second 
D)  bytes per minute

Question 16

Match each item with a statement below.
a.switch
b.default route
c.half-duplex mode
d.router
e.bandwidth sharing
f.repeater
g.CTS
h.network interface card
i.uplink port
j.network bandwidth
-how devices connected to a hub use network bandwidth

Accepted Answer

The answer of Match each item with a statement below.
a.switch
b.default...

Question 17

What is the purpose of the default route?

Accepted Answer

A)  It serves as a guideline for how to configure routes. 
B)  It's a route set by Microsoft so that all information comes to their servers first. 
C)  It's where the router sends all packets with destination addresses of which it has no knowledge. 
D)  It's a route that all routers use to get to the Internet.

Question 18

What does it mean if the full-duplex indicator on a switch port is on?

Accepted Answer

A)  The switch is detecting collisions. 
B)  The port can transmit and receive frames simultaneously. 
C)  Bandwidth sharing is enabled. 
D)  The MAC address table is full.

Question 19

If a router receives a packet and it does not have an entry in its routing table for the destination network, it will send the packet to its default route, if configured.

Accepted Answer

A) True 
 B)False

Question 20

Which of the following is NOT a function of a hub?

Accepted Answer

A)  cleans up the signal 
B)  transmits the frame out the correct port 
C)  receives the signal from a connected computer on one of its ports 
D)  regenerates the signal

Exam 2: Network Hardware Essentials

A computer's default gateway setting is the MAC address of a router on a remote network.

Match each item with a statement below. a.switch b.default route c.half-duplex mode d.router e.bandwidth sharing f.repeater g.CTS h.network interface card i.uplink port j.network bandwidth -designated port on a hub or switch used to connect to another hub or switch

The network ____________ is a measurement of the amount of data that can pass through a network in a certain period of time.

What command would you issue from the command prompt to test whether your computer has connectivity to the network?

A wireless access point is most like which other network device, in that all computers send signals through it to communicate with other computers?

A switch operating in full ___________ mode can send and receive data at the same time.

Match each item with a statement below. a.switch b.default route c.half-duplex mode d.router e.bandwidth sharing f.repeater g.CTS h.network interface card i.uplink port j.network bandwidth -amount of data that can be transferred on a network in a specified interval

What component of the computer contains a MAC address?

What is the MAC address of a computer?

Match each item with a statement below. a.switch b.default route c.half-duplex mode d.router e.bandwidth sharing f.repeater g.CTS h.network interface card i.uplink port j.network bandwidth -device that uses MAC addresses to determine the destination of frame

When a NIC is in promiscuous mode, it will process only the frames in which the destination MAC address matches its own MAC address.

Match each item with a statement below. a.switch b.default route c.half-duplex mode d.router e.bandwidth sharing f.repeater g.CTS h.network interface card i.uplink port j.network bandwidth -device that only regenerates incoming signals

In a computer's IP address settings, the default _____________ is the address of the router to which a computer sends all packets that are intended for networks outside of its own.

Just as a switch keeps records of MAC addresses that it has learned, so does your computer. What protocol does your computer use to learn MAC addresses?

When referring to network bandwidth, what is the basic unit of measurement?

Match each item with a statement below. a.switch b.default route c.half-duplex mode d.router e.bandwidth sharing f.repeater g.CTS h.network interface card i.uplink port j.network bandwidth -how devices connected to a hub use network bandwidth

What is the purpose of the default route?

What does it mean if the full-duplex indicator on a switch port is on?

If a router receives a packet and it does not have an entry in its routing table for the destination network, it will send the packet to its default route, if configured.

Which of the following is NOT a function of a hub?