Question 1

The ring gear in a Ford transmission serves as an input member.

Accepted Answer

A) True 
 B)False

Question 2

When comparing the design differences of the Toyota A340F and the A340H, you find the A340F uses a ____________________ controlled 4WD transfer case and the A340H has an ____________________ controlled 4WD transfer case.

Accepted Answer

The answer of When comparing the design differences of the...

Question 3

Which of the following is not true of a Ford 5R55E transmission?

Accepted Answer

A) An additional gearset was added to achieve the fifth gear. 
B) It is an updated version of the A4LD 
C) It uses additional control devices for 5th gear. 
D) None of the above are correct.

Question 4

Technician A says by using selective thrust washers, end play is often corrected. Technician B says by using selective snap rings, end play is often corrected. Who is correct?

Accepted Answer

A) A only 
B) B only 
C) Both A and B 
D) Neither A nor B

Question 5

Technician A says the Mercedes-Benz 7G-Tronic was the first seven-speed automatic transmission. Technician B says this unit allows the electronic control unit to "skip" gears when upshifting or downshifting. Who is correct?

Accepted Answer

A) A only 
B) B only 
C) Both A and B 
D) Neither A nor B

Question 6

Technician A says that a solenoid that is controlled by a computer is switched on or off on the ground side of the circuit. Technician B says a Chrysler-built unit, when operating in "limp-in" mode, will allow operation in all gear ranges but at reduced efficiency. Who is correct?

Accepted Answer

A) A only 
B) B only 
C) Both A and B 
D) Neither A nor B

Question 7

The ____________________ works with the accumulator valve to cushion 4th clutch application by absorbing some of the apply pressure.

Accepted Answer

The answer of The ____________________ works with the accumulator valve...

Question 8

Describe the operation of Honda's acceleration clutch.

Accepted Answer

The answer of Describe the operation of Honda's acceleration clutch....

Question 9

Technician A says different forward gears are provided by a tandem planetary gear set in Honda transaxles. Technician B says the final drive unit in Honda and Acura transaxles is a planetary gear set. Who is correct?

Accepted Answer

A) A only 
B) B only 
C) Both A and B 
D) Neither A nor B

Question 10

Which of the following is not true of a Simpson geartrain?

Accepted Answer

A) It contains two ring gears. 
B) It uses two separate planetary gear sets. 
C) It uses a common sun gear. 
D) It uses a common planetary pinion carrier.

Question 11

Explain how the gears in the transaxle are driven in a GM 4T60.

Accepted Answer

The answer of Explain how the gears in the transaxle...

Question 12

Technician A says two planetary units that do not share a common gear set member are used in the 4T60. Technician B says the 4T60 transaxle used to be referred to as the 440-T4. Who is correct?

Accepted Answer

A) A only 
B) B only 
C) Both A and B 
D) Neither A nor B

Question 13

Technician A says the Chrysler RFE Series uses three brake bands. Technician B says that the RFE Series uses two brake bands. Who is correct?

Accepted Answer

A) A only 
B) B only 
C) Both A and B 
D) Neither A nor B

Question 14

Technician A says two sun gears, two sets of planet gears, and a common sun gear are the components of a Ravigneaux gear set. Technician B says two planetary gear sets that share a common ring gear make up a Simpson gear set. Who is correct?

Accepted Answer

A) A only 
B) B only 
C) Both A and B 
D) Neither A nor B

Question 15

The Ravigneaux gear set shares a common sun gear.

Accepted Answer

A) True 
 B)False

Question 16

The ____________________ directs fluid flow according to shift solenoid operation, actuator feed pressure, and return spring force to control 2-3 and 3-2 shifts.

Accepted Answer

The answer of The ____________________ directs fluid flow according to...

Question 17

The ____________________ directs fluid flow according to shift solenoid operation, actuator and 4th clutch feed pressure, and return spring force to control 3-4 and 4-3 shifts.

Accepted Answer

The answer of The ____________________ directs fluid flow according to...

Question 18

Technician A says a square-cut seal is designed to roll over when a part is fitted over them. Technician B says before installing some seals, they must be cut to size. Who is correct?

Accepted Answer

A) A only 
B) B only 
C) Both A and B 
D) Neither A nor B

Question 19

Many Lexus vehicles are equipped with one of the following transmissions: the A760H, A761E, or the A960E.

Accepted Answer

A) True 
 B)False

Question 20

Most Toyota/Lexus transmission models have a centrifugal fluid pressure-canceling mechanism.

Accepted Answer

A) True 
 B)False

Exam 10: Common Automatic Transmissions

The ring gear in a Ford transmission serves as an input member.

When comparing the design differences of the Toyota A340F and the A340H, you find the A340F uses a controlled 4WD transfer case and the A340H has an controlled 4WD transfer case.

Which of the following is not true of a Ford 5R55E transmission?

Technician A says by using selective thrust washers, end play is often corrected. Technician B says by using selective snap rings, end play is often corrected. Who is correct?

Technician A says the Mercedes-Benz 7G-Tronic was the first seven-speed automatic transmission. Technician B says this unit allows the electronic control unit to "skip" gears when upshifting or downshifting. Who is correct?

Technician A says that a solenoid that is controlled by a computer is switched on or off on the ground side of the circuit. Technician B says a Chrysler-built unit, when operating in "limp-in" mode, will allow operation in all gear ranges but at reduced efficiency. Who is correct?

The ____________________ works with the accumulator valve to cushion 4th clutch application by absorbing some of the apply pressure.

Describe the operation of Honda's acceleration clutch.

Technician A says different forward gears are provided by a tandem planetary gear set in Honda transaxles. Technician B says the final drive unit in Honda and Acura transaxles is a planetary gear set. Who is correct?

Which of the following is not true of a Simpson geartrain?

Explain how the gears in the transaxle are driven in a GM 4T60.

Technician A says two planetary units that do not share a common gear set member are used in the 4T60. Technician B says the 4T60 transaxle used to be referred to as the 440-T4. Who is correct?

Technician A says the Chrysler RFE Series uses three brake bands. Technician B says that the RFE Series uses two brake bands. Who is correct?

Technician A says two sun gears, two sets of planet gears, and a common sun gear are the components of a Ravigneaux gear set. Technician B says two planetary gear sets that share a common ring gear make up a Simpson gear set. Who is correct?

The Ravigneaux gear set shares a common sun gear.

The ____________________ directs fluid flow according to shift solenoid operation, actuator feed pressure, and return spring force to control 2-3 and 3-2 shifts.

The ____________________ directs fluid flow according to shift solenoid operation, actuator and 4th clutch feed pressure, and return spring force to control 3-4 and 4-3 shifts.

Technician A says a square-cut seal is designed to roll over when a part is fitted over them. Technician B says before installing some seals, they must be cut to size. Who is correct?

Many Lexus vehicles are equipped with one of the following transmissions: the A760H, A761E, or the A960E.

Most Toyota/Lexus transmission models have a centrifugal fluid pressure-canceling mechanism.