Question 1

When an SSID is configured with Sign-On Splash page enabled, which two settings must be configured for unauthenticated clients to have full network access and not be allow listed? (Choose two.)

Accepted Answer

A)   Controller disconnection behavior
B)   Captive Portal strength
C)   Simultaneous logins
D)   Firewall & traffic shaping
E)   RADIUS for splash page settings A,B

Question 2

Air Marshal has contained a malicious SSID. What are two effects on connectivity? (Choose two.)

Accepted Answer

A)   Currently associated clients stay connected.
B)   New clients can connect.
C)   Currently associated clients are affected by restrictive traffic shaping rules.
D)   New clients cannot connect.
E)   Currently associated clients are disconnected. D,E

Question 3

Which configuration step is necessary when automatic updating is required of iOS apps provisioned through Systems Manager that are found in the App Store?

Accepted Answer

A)   No configuration step is necessary; automatic updating is the default behavior.
B)   Configure automatic updating of iOS devices in the Meraki installed profile.
C)   Create a security policy that enables automatic updates.
D)   Create a profile with automatic update enabled and apply it to iOS devices. C

Question 4

Where should a network admin navigate to investigate wireless mesh information between Meraki APs?

Accepted Answer

A)   Wireless > Monitor > Access Points > AP > RF
B)   Wireless > Configure > Radio Settings
C)   Wireless > Monitor > Wireless Health
D)   Wireless > Monitor > RF Spectrum

Question 5

A Cisco Meraki MV camera is monitoring an office and its field of vision currently captures work desks and employee computer screens. However, recording employee computer screens is prohibited by local regulation. Which feature in Dashboard can be used to preserve the current position of the camera while also meeting regulation requirements?

Accepted Answer

A)   zone exclusion
B)   privacy window
C)   area or interest
D)   sensor crop
E)   restricted mode

Question 6

Refer to the exhibit. What is the minimal Cisco Meraki Insight licensing requirement?

Accepted Answer

A)   A single Meraki Insight license must be configured on network A to gain Web App Health visibility on network B
B)   A single Meraki Insight license must be configured on network B to gain Web App Health visibility on network B
C)   A single Meraki Insight license must be configured on network A, and a single license must be configured on network B, to gain Web App Health visibility on network B
D)   Two Meraki Insight licenses must be configured on network A to gain Web App Health visibility on network B
E)   Two Meraki Insight licenses must be configured on network A and a single license must be configured on network B, to gain Web App Health visibility on network B

Question 7

One thousand concurrent users stream video to their laptops. A 30/70 split between 2.4 GHz and 5 GHz is used. Based on client count, how many APs (rounded to the nearest whole number) are needed?

Accepted Answer

A)   26
B)   28
C)   30
D)   32

Question 8

Refer to the exhibit. What are the Loss and Average Latency statistics based on?

Accepted Answer

A)   responses that the MX appliance receives on the connectivity-testing hostnames on the Insight > Web App Health page
B)   responses that the MX appliance receives on the connectivity-testing IP addresses on the Security & SD-WAN > Firewall page
C)   responses that the MX appliance receives on the connectivity-testing IP address that is configured on the Security & SD-WAN > SD-WAN & Traffic Shaping page
D)   responses that the MX appliance receives on the connectivity-testing IP addresses on the Help > Firewall info page

Question 9

Refer to the exhibit. For an AP that displays this alert, which network access control method must be in use?

Accepted Answer

A)   preshared key
B)   WPA2-enterprise with my RADIUS server
C)   splash page with my RADIUS server
D)   MAC-based access control with RADIUS server

Question 10

What happens to an unsupervised iOS device when the "Meraki management" profile is removed?

Accepted Answer

A)   The "Meraki management" profile is removed. All configuration profiles that Systems Manager pushed remain.
B)   The "Meraki management" profile is removed. All configuration profiles that Systems Manager pushed are also removed.
C)   The "Meraki management" profile is removed and then pushed automatically by Systems Manager.
D)   The "Meraki management" profile cannot be removed.

Question 11

Refer to the exhibit. Assuming this MX has established a full tunnel with its VPN peer, how will the MX route the WebEx traffic?

Accepted Answer

A)   WebEx traffic will prefer WAN 2 as long as it meets the thresholds in the "Conf" performance class.
B)   WebEx traffic will prefer WAN 1 as it is the primary uplink.
C)   WebEx traffic will prefer WAN 2 as long as it is up.
D)   WebEx traffic will be load-balanced between both active WAN links.

Question 12

What are two ways peers interact with ports that Auto VPN uses? (Choose two.)

Accepted Answer

A)   For IPsec tunneling, peers use high UDP ports within the 32768 to 61000 range.
B)   Peers contact the VPN registry at UDP port 9350.
C)   For IPsec tunneling, peers use high TCP ports within the 32768 to 61000 range.
D)   Peers contact the VPN registry at TCP port 9350.
E)   For IPsec tunneling, peers use UDP ports 500 and 4500.

Question 13

How is high-availability supported for Cisco Meraki devices?

Accepted Answer

A)   Only the MX Security Appliances that use VRRP support high availability.
B)   An active/active high-availability pair is recommended for MX Security Appliances.
C)   The MX Security Appliances and MS Series Switches that use VRRP support an active/passive high-availability pair.
D)   The MX Security Appliances and MS Series Switches that use HSRP support an active/passive high-availability pair.

Question 14

Which VLAN is used to source pings across the site-to-site VPN when using the MX Live tools?

Accepted Answer

A)   highest VLAN ID that is configured and set to NO to use VPN
B)   lowest VLAN ID that is configured and set to YES to use VPN
C)   highest VLAN ID that is configured and set to YES to use VPN
D)   lowest VLAN ID configured and set to NO to use VPN

Question 15

Refer to the exhibit. During a Meraki AP deployment, the default SSID that the exhibit shows is broadcast. What causes this behavior?

Accepted Answer

A)   An AP does not have a wired connection to the network.
B)   An AP cannot connect to the default gateway.
C)   An AP has never connected to the Meraki Cloud Controller.
D)   An AP has Site Survey mode enabled.

Question 16

What occurs when a configuration change is made to an MX network that is bound to a configuration template?

Accepted Answer

A)   The configuration change in the bound network is combined with the template configuration inside the template.
B)   The more restrictive configuration is preferred.
C)   The configuration change in the bound network overrides the template configuration.
D)   The template configuration overrides the configuration change in the bound network.

Question 17

When wireless SSIDs are configured in Dashboard, which setting on the Access Control page affects the ability of a 2.4 GHz only client device from associating to the WLAN for the first time?

Accepted Answer

A)   Content filtering
B)   Bridge mode
C)   802.11r
D)   Dual band operating with Band Steering

Question 18

Refer to the exhibit. What does the MX Security Appliance send to determine whether VPN traffic exceeds the configured latency threshold in the VoIP custom performance class?

Accepted Answer

A)   1000-byte TCP probes every second, through VPN tunnels that are established over the primary WAN link.
B)   100-byte UDP probes every second, through VPN tunnels that are established over every WAN link.
C)   100-byte UDP probes every second, through VPN tunnels that are established over the primary WAN link.
D)   1000-byte TCP probes every second, through VPN tunnels that are established over every WAN link.

Question 19

Refer to the exhibit. Which two actions are required to optimize load balancing asymmetrically with a 4:1 ratio between links? (Choose two.)

Accepted Answer

A)   Change the primary uplink to "none".
B)   Add an internet traffic preference that defines the load-balancing ratio as 4:1.
C)   Enable load balancing.
D)   Set the speed of the cellular uplink to zero.
E)   Change the assigned speeds of WAN 1 and WAN 2 so that the ratio is 4:1.

Question 20

Which order is accurate for a firmware upgrade on MX appliances in a high-availability configuration?

Accepted Answer

A)   starts on the secondary MX appliance and then occurs on the primary MX appliance
B)   starts on both MX appliances at the same time and then reboots both appliances after traffic on the primary MX appliance ceases
C)   starts on both MX appliances at the same time and then immediately reboots both appliances
D)   starts on the primary MX appliance and then occurs on the secondary MX appliance

Exam 46: Securing Cisco Networks with Sourcefire FireAMP Endpoints