Question 1

Transportation of precast members accounts for about

Accepted Answer

A)  20-25%ofthecostof production and assembling
B)  10-15% of the cost of production and assembling
C)  10-20% of the cost of production and assembling
D)  5-15% of the cost of production and assembling B

Question 2

Which of the following does not comes under the types of progressive collapse

Accepted Answer

A)  domino-type collapse
B)  section type collapse
C)  stability type collapse
D)  mixed-type collapse C

Question 3

Plant fabrication is suited better for

Accepted Answer

A)  large number of small prefabricates
B)  large e long panel members
C)  standard is members
D)  limited production A

Question 4

Depending on the degree of workability and placing condition determine the

Accepted Answer

A)  slump value
B)  the maximum size of aggregate
C)  the amount of mixing water
D)  the minimum water-cement ratio

Question 5

Choose the correct answer.

Accepted Answer

A)  converting static load into dynamic load is known as equivalent design loads.
B)  converting dynamic load into static load is known as equivalent design loads.
C)  both a &b
D)  none of the above

Question 6

The elastic rebound theory is an explanationfor how ... is spread duringearthquakes

Accepted Answer

A)  load
B)  stress
C)  energy
D)  intensity of load

Question 7

Choose the correct answer in terms of special requirements for building in High Seismic Zones

Accepted Answer

A)  the height of the building shall generally restricted to 5 stores in zone iv
B)  the height of the building shall generally restricted to 7 stores in zone iv
C)  the height of the building shall generally restricted to 8 stores in zone iv
D)  the height of the building shall generally restricted to 10 stores in zone iv

Question 8

In places where transportation of large members is difficult what kind of fabrication is preferred?

Accepted Answer

A)  plant prefabrication
B)  site fabrication
C)  standardisation
D)  prefabricate systems

Question 9

In a Prefabricated R C floors in a cyclone prone zone the Structural deck concrete of grade not leaner than .............. should be provided over pre-cast components to act monolithic with them.

Accepted Answer

A)  m10
B)  m15
C)  m20
D)  m25

Question 10

How many methods are generally used to avoid the disproportionate collapse in a building?

Accepted Answer

A)  one
B)  two
C)  three
D)  zero

Question 11

................... is the factor used to obtain the design seismic force depending on the functional use of the structure, characterized by hazardous consequences of its failure, its post-earthquake functional need, historic value, or economic importance.

Accepted Answer

A)  importance factor
B)  response reduction factor
C)  all of the above
D)  none of the above

Question 12

Damping is the energy dissipation properties of a material or system under stress.

Accepted Answer

A)  dynamic stress
B)  static stress
C)  non cyclic stress
D)  cyclic stress

Question 13

Choose the correct answer in terms of special requirements for building in High Seismic Zones

Accepted Answer

A)  the height of the building shall generally restricted to 5 stores in zone v
B)  the height of the building shall generally restricted to 6 stores in zone v
C)  the height of the building shall generally restricted to 7 stores in zone v
D)  the height of the building shall generally restricted to 8 stores in zone v

Question 14

Which of the following defines Magnitude?

Accepted Answer

A)  the severity of earthquake shaking is assessed using a descriptive scale
B)  quantitative measure of the size of the earthquake at its source
C)  both a &b
D)  none of the above

Exam 2: Seismic Design and Fabrication Techniques for Difficult Transportation

Transportation of precast members accounts for about

Which of the following does not comes under the types of progressive collapse

Plant fabrication is suited better for

Depending on the degree of workability and placing condition determine the

Choose the correct answer.

The elastic rebound theory is an explanationfor how ... is spread duringearthquakes

Choose the correct answer in terms of special requirements for building in High Seismic Zones

In places where transportation of large members is difficult what kind of fabrication is preferred?

In a Prefabricated R C floors in a cyclone prone zone the Structural deck concrete of grade not leaner than .............. should be provided over pre-cast components to act monolithic with them.

How many methods are generally used to avoid the disproportionate collapse in a building?

................... is the factor used to obtain the design seismic force depending on the functional use of the structure, characterized by hazardous consequences of its failure, its post-earthquake functional need, historic value, or economic importance.

Damping is the energy dissipation properties of a material or system under stress.

Choose the correct answer in terms of special requirements for building in High Seismic Zones

Which of the following defines Magnitude?