Question 1

Which of the following combinations will you find in a switching table?

Accepted Answer

A)  application/destination port number 
B)  IP address/exit interface 
C)  destination network/next Hop 
D)  MAC address/switch port number 
A)  application/destination port number 
B)  IP address/exit interface 
C)  destination network/next Hop 
D)  MAC address/switch port number

Question 2

On a router configured to use RIP,the number of routers a packet must travel between before it reaches its destination is called what? (Choose two.)

Accepted Answer

A)  metric 
B)  hop count 
C)  timestamp 
D)  aging time 
A)  metric 
B)  hop count 
C)  timestamp 
D)  aging time

Question 3

Which of the following is a common link-state protocol?

Accepted Answer

A)  OSPF 
B)  RIPv2 
C)  EIGRP 
D)  BGP 
A)  OSPF 
B)  RIPv2 
C)  EIGRP 
D)  BGP

Question 4

Match each item with a statement below.​
-frame is sent to the destination port immediately after reading the destination and source MAC address

Accepted Answer

A) distance-vector protocol 
B) fragment-free switching 
C) cut-through switching 
D) store-and-forward switching 
E) Spanning Tree Protocol
F)trunk port
G)EGP
H)link-state protocol
I)metric
J)IGP 
A) distance-vector protocol 
B) fragment-free switching 
C) cut-through switching 
D) store-and-forward switching 
E) Spanning Tree Protocol
F)trunk port
G)EGP
H)link-state protocol
I)metric
J)IGP

Question 5

Why should you change the SSID on your wireless router?

Accepted Answer

The SSID is always set to a default valu

Question 6

A distance-vector protocol sends updates to its neighbors that include the entire contents of its routing table.

Accepted Answer

A) True 
 B)False

Question 7

Match each item with a statement below.​
-routing protocol category in which the routing protocol is used to exchange routing information within an autonomous system.

Accepted Answer

A) distance-vector protocol 
B) fragment-free switching 
C) cut-through switching 
D) store-and-forward switching 
E) Spanning Tree Protocol
F)trunk port
G)EGP
H)link-state protocol
I)metric
J)IGP 
A) distance-vector protocol 
B) fragment-free switching 
C) cut-through switching 
D) store-and-forward switching 
E) Spanning Tree Protocol
F)trunk port
G)EGP
H)link-state protocol
I)metric
J)IGP

Question 8

One type of security for wireless networks involves entering a list of the MAC addresses for the devices that are allowed to access the network and excluding all others.This is called MAC ____________.

Accepted Answer

The answer of One type of security for wireless networks...

Question 9

Match each item with a statement below.​
-designed to stop switching loops

Accepted Answer

A) distance-vector protocol 
B) fragment-free switching 
C) cut-through switching 
D) store-and-forward switching 
E) Spanning Tree Protocol
F)trunk port
G)EGP
H)link-state protocol
I)metric
J)IGP 
A) distance-vector protocol 
B) fragment-free switching 
C) cut-through switching 
D) store-and-forward switching 
E) Spanning Tree Protocol
F)trunk port
G)EGP
H)link-state protocol
I)metric
J)IGP

Question 10

What are the three ways that a router can populate its routing table?

Accepted Answer

It knows about networks that a

Which of the following combinations will you find in a switching table?

On a router configured to use RIP,the number of routers a packet must travel between before it reaches its destination is called what? (Choose two.)

Which of the following is a common link-state protocol?

Match each item with a statement below. -frame is sent to the destination port immediately after reading the destination and source MAC address

Why should you change the SSID on your wireless router?

A distance-vector protocol sends updates to its neighbors that include the entire contents of its routing table.

Match each item with a statement below. -routing protocol category in which the routing protocol is used to exchange routing information within an autonomous system.

One type of security for wireless networks involves entering a list of the MAC addresses for the devices that are allowed to access the network and excluding all others.This is called MAC ____________.

Match each item with a statement below. -designed to stop switching loops

What are the three ways that a router can populate its routing table?

Introduction to Computer Networks

Network Hardware Essentials

Network Topologies and Technologies

Network Media

Network Protocols

Ip Addressing

Network Reference Models and Standards

Introduction to Network Security

Wide Area Networking and Cloud Computing

Network Operating System Fundamentals

Network Management and Administration

Troubleshooting and Support

Filters

Exam 8: Network Hardware in Depth

Which of the following combinations will you find in a switching table?

On a router configured to use RIP,the number of routers a packet must travel between before it reaches its destination is called what? (Choose two.)

Which of the following is a common link-state protocol?

Match each item with a statement below.​ -frame is sent to the destination port immediately after reading the destination and source MAC address

Why should you change the SSID on your wireless router?

A distance-vector protocol sends updates to its neighbors that include the entire contents of its routing table.

Match each item with a statement below.​ -routing protocol category in which the routing protocol is used to exchange routing information within an autonomous system.

One type of security for wireless networks involves entering a list of the MAC addresses for the devices that are allowed to access the network and excluding all others.This is called MAC ____________.

Match each item with a statement below.​ -designed to stop switching loops

What are the three ways that a router can populate its routing table?

Introduction to Computer Networks

Network Hardware Essentials

Network Topologies and Technologies

Network Media

Network Protocols

Ip Addressing

Network Reference Models and Standards

Introduction to Network Security

Wide Area Networking and Cloud Computing

Network Operating System Fundamentals

Network Management and Administration

Troubleshooting and Support

Filters

Match each item with a statement below. -frame is sent to the destination port immediately after reading the destination and source MAC address

Match each item with a statement below. -routing protocol category in which the routing protocol is used to exchange routing information within an autonomous system.

Match each item with a statement below. -designed to stop switching loops