Question 1

A gage number represents the weight per square foot of a particular material.

Accepted Answer

A) True 
 B)False

Question 2

Which kind of development would be used to develop a pattern?

Accepted Answer

A) parallel line development 
B) truncated line development 
C)  radial line development 
D)  triangulation line development 
A) parallel line development 
B) truncated line development 
C)  radial line development 
D)  triangulation line development

Question 3

A piece of sheet metal that has the edge bent at a 90-degree angle forms a:

Accepted Answer

A) lap seam 
B) standing seam 
C)  single flange 
D)  locked seam 
A) lap seam 
B) standing seam 
C)  single flange 
D)  locked seam

Question 4

Which of the following is not a major kind of surface development?

Accepted Answer

A) parallel line development 
B) cubic development 
C)  radial line development 
D)  triangulation development 
A) parallel line development 
B) cubic development 
C)  radial line development 
D)  triangulation development

Question 5

Which of the following elements must be located or laid out before a development can actually be started?

Accepted Answer

A) Lengths 
B) true distances 
C)  station lines 
D)  both A and B 
A) Lengths 
B) true distances 
C)  station lines 
D)  both A and B

Question 6

When creating a pattern development, the designer must consider all of the following except:

Accepted Answer

A) type of material 
B) size of the pattern 
C)  placement of the seams and tabs 
D)  quantity to be produced 
A) type of material 
B) size of the pattern 
C)  placement of the seams and tabs 
D)  quantity to be produced

Question 7

The gage system of calling out the thickness of a material is being phased out because:

Accepted Answer

A) It is out-of-date. 
B) It is difficult to learn 
C)  It is inaccurate. 
D)  none of the above 
A) It is out-of-date. 
B) It is difficult to learn 
C)  It is inaccurate. 
D)  none of the above

Question 8

When creating a lap or seam which of the following does not need to be considered?

Accepted Answer

A) method of fastening 
B) thickness of the metal 
C)  type of surface 
D)  type of metal 
A) method of fastening 
B) thickness of the metal 
C)  type of surface 
D)  type of metal

Question 9

The less the bend angle, the greater the amount of bend allowance needed.

Accepted Answer

A) True 
 B)False

Question 10

Bend allowance refers to the practice of calculating the length of material needed by each bend.

Accepted Answer

A) True 
 B)False

Question 11

The purpose of a lap joint is to:

Accepted Answer

A) reinforce the edge 
B) join two separate pieces 
C)  roll the end of the material 
D)  all of the above 
A) reinforce the edge 
B) join two separate pieces 
C)  roll the end of the material 
D)  all of the above

Question 12

Which of the following is an example of a flat-plane surface?

Accepted Answer

A) funnel 
B) cereal box 
C)  soup can 
D)  tabletop 
A) funnel 
B) cereal box 
C)  soup can 
D)  tabletop

Question 13

A No. 16 gage piece of aluminum is slightly heavier than a No. 17 piece of aluminum.

Accepted Answer

A) True 
 B)False

Question 14

When creating a simple box, most of the fold lines are perpendicular to the baseline.

Accepted Answer

A) True 
 B)False

Question 15

To create a cylinder for a soup can, what type of pattern development would be drawn?

Accepted Answer

A) radial line 
B) triangulation 
C)  parallel line 
D)  fold line 
A) radial line 
B) triangulation 
C)  parallel line 
D)  fold line

A gage number represents the weight per square foot of a particular material.

Which kind of development would be used to develop a pattern?

A piece of sheet metal that has the edge bent at a 90-degree angle forms a:

Which of the following is not a major kind of surface development?

Which of the following elements must be located or laid out before a development can actually be started?

When creating a pattern development, the designer must consider all of the following except:

The gage system of calling out the thickness of a material is being phased out because:

When creating a lap or seam which of the following does not need to be considered?

The less the bend angle, the greater the amount of bend allowance needed.

Bend allowance refers to the practice of calculating the length of material needed by each bend.

The purpose of a lap joint is to:

Which of the following is an example of a flat-plane surface?

A No. 16 gage piece of aluminum is slightly heavier than a No. 17 piece of aluminum.

When creating a simple box, most of the fold lines are perpendicular to the baseline.

To create a cylinder for a soup can, what type of pattern development would be drawn?

Introduction

Employability Skills for Drafting and Design Technicians

Drafting Tools: Conventional, Cad, and Solid Modeling

Sketching and Lettering for Engineering Communication

Geometric Construction

Spatial Visualization and Multiview Drawings

Dimensioning and Notation

Sectional Views

Auxiliary Views

Descriptive Geometry

Solid 3D Modeling: Computational Design and Analysis

Geometric Dimensioning and Tolerancing

Fasteners

Springs

Cams

Gears

Assembly and Detail Drawings for Design

Pictorial Drawings

Welding

Modern Manufacturing: Materials, Processes, and Automation

The Design Process and Advanced Concepts

Filters

Exam 11: Patterns and Developments

A gage number represents the weight per square foot of a particular material.

Which kind of development would be used to develop a pattern?

A piece of sheet metal that has the edge bent at a 90-degree angle forms a:

Which of the following is not a major kind of surface development?

Which of the following elements must be located or laid out before a development can actually be started?

When creating a pattern development, the designer must consider all of the following except:

The gage system of calling out the thickness of a material is being phased out because:

When creating a lap or seam which of the following does not need to be considered?

The less the bend angle, the greater the amount of bend allowance needed.

Bend allowance refers to the practice of calculating the length of material needed by each bend.

The purpose of a lap joint is to:

Which of the following is an example of a flat-plane surface?

A No. 16 gage piece of aluminum is slightly heavier than a No. 17 piece of aluminum.

When creating a simple box, most of the fold lines are perpendicular to the baseline.

To create a cylinder for a soup can, what type of pattern development would be drawn?

Introduction

Employability Skills for Drafting and Design Technicians

Drafting Tools: Conventional, Cad, and Solid Modeling

Sketching and Lettering for Engineering Communication

Geometric Construction

Spatial Visualization and Multiview Drawings

Dimensioning and Notation

Sectional Views

Auxiliary Views

Descriptive Geometry

Solid 3D Modeling: Computational Design and Analysis

Geometric Dimensioning and Tolerancing

Fasteners

Springs

Cams

Gears

Assembly and Detail Drawings for Design

Pictorial Drawings

Welding

Modern Manufacturing: Materials, Processes, and Automation

The Design Process and Advanced Concepts

Filters