Question 1

Ammeters should be connected ________ with the circuit being tested.

Accepted Answer

A)  in series 
B)  across a load 
C)  in parallel 
D)  None of these 
A)  in series 
B)  across a load 
C)  in parallel 
D)  None of these

Question 2

When using a test light to probe for electrical power, the alligator clip is connected to ________.

Accepted Answer

A)  a clean metal part of the body 
B)  the battery negative terminal 
C)  the battery positive terminal 
D)  Either A or B 
A)  a clean metal part of the body 
B)  the battery negative terminal 
C)  the battery positive terminal 
D)  Either A or B

Question 3

When testing a diode with the multimeter set on "Diode Check" a reading of 0.6 volts is obtained. This indicates that the diode being tested is a(n) ________.

Accepted Answer

A)  light emitting diode (LE
D)  
B)  open diode 
C)  silicon diode 
D)  shorted diode 
A)  light emitting diode (LE
D)  
B)  open diode 
C)  silicon diode 
D)  shorted diode

Question 4

Which device may be useful for testing hall effect sensors?

Accepted Answer

A)  Low power test light 
B)  Logic probe 
C)  Both A and B 
D)  Neither A nor B 
A)  Low power test light 
B)  Logic probe 
C)  Both A and B 
D)  Neither A nor B

Ammeters should be connected ________ with the circuit being tested.

When using a test light to probe for electrical power, the alligator clip is connected to ________.

When testing a diode with the multimeter set on "Diode Check" a reading of 0.6 volts is obtained. This indicates that the diode being tested is a(n) ________.

Which device may be useful for testing hall effect sensors?

The Diagnostic Process

Gasoline, Alternative Fuels, and Diesel Fuels

Oscilloscopes and Dsos

Engine Systems

In-Vehicle Engine Service

Valve Train and Variable Valve Timing Diagnosis

Engine and Misfire Diagnosis

Can and Network Communications

Onboard Diagnosis

Global Obd Ii and Mode 06

Immobilizer Systems

Starting and Charging System Diagnosis

Ignition System Operation and Diagnosis

Temperature Sensors

Throttle Position Tp Sensors

Map and Maf Sensors

Electronic Throttle Control Systems

Oxygen Sensors

Fuel Trim Diagnosis

Fuel Pumps, Lines, and Filters

Fuel-Injection Components and Operation

Gasoline Direct-Injection Systems

Fuel-Injection System Diagnosis and Service

Electronic Transmission Controls

Vehicle Emissions Standards and Testing

Emission Control Devices Operation and Diagnosis

Module Reprogramming

Symptom-Based Diagnosis

Filters

Exam 3: Circuit Testers and Digital Meters

Ammeters should be connected ________ with the circuit being tested.

When using a test light to probe for electrical power, the alligator clip is connected to ________.

When testing a diode with the multimeter set on "Diode Check" a reading of 0.6 volts is obtained. This indicates that the diode being tested is a(n) ________.

Which device may be useful for testing hall effect sensors?

The Diagnostic Process

Gasoline, Alternative Fuels, and Diesel Fuels

Oscilloscopes and Dsos

Engine Systems

In-Vehicle Engine Service

Valve Train and Variable Valve Timing Diagnosis

Engine and Misfire Diagnosis

Can and Network Communications

Onboard Diagnosis

Global Obd Ii and Mode 06

Immobilizer Systems

Starting and Charging System Diagnosis

Ignition System Operation and Diagnosis

Temperature Sensors

Throttle Position Tp Sensors

Map and Maf Sensors

Electronic Throttle Control Systems

Oxygen Sensors

Fuel Trim Diagnosis

Fuel Pumps, Lines, and Filters

Fuel-Injection Components and Operation

Gasoline Direct-Injection Systems

Fuel-Injection System Diagnosis and Service

Electronic Transmission Controls

Vehicle Emissions Standards and Testing

Emission Control Devices Operation and Diagnosis

Module Reprogramming

Symptom-Based Diagnosis

Filters