Exam 22: Regulated Power Supplies Key
Exam 1: Introduction38 Questions
Exam 2: Semoconductors50 Questions
Exam 3: Diode Theory Key50 Questions
Exam 4: Diode Circuits48 Questions
Exam 5: Special-Purpose Diodes Key50 Questions
Exam 6: BJT Fumdamentals50 Questions
Exam 7: BJT Biasing50 Questions
Exam 7: Basic BJT Amplifiers52 Questions
Exam 9: Multistage,CC,and CB Amplifiers50 Questions
Exam 10: Power Amplifiers48 Questions
Exam 11: JFETS50 Questions
Exam 12: Mosfets46 Questions
Exam 13: Thyristors50 Questions
Exam 14: Frequency Effects50 Questions
Exam 15: Differential Amplifiers50 Questions
Exam 16: Operational Amplifiers50 Questions
Exam 17: Negative Feedback49 Questions
Exam 18: Linear OP AMP Circuits50 Questions
Exam 19: Active Filters Key50 Questions
Exam 20: Nonlinear Op-Amp Circuit Applications Key50 Questions
Exam 21: Oscillators Key50 Questions
Exam 22: Regulated Power Supplies Key49 Questions
Select questions type
The transistor of a series voltage regulator is called a
Free
(Multiple Choice)
4.8/5
(33)
Correct Answer:
A
The transistor of a series regulator is called a pass transistor because the entire load current passes through it.
Free
(True/False)
4.8/5
(41)
Correct Answer:
True
A short-circuit protection circuit used with IC voltage regulators can be configured using
Free
(Multiple Choice)
4.8/5
(44)
Correct Answer:
B
A basic topology for switching regulators that always produces a negative output voltage when driven by a positive input voltage is the
(Multiple Choice)
4.8/5
(35)
When analyzing a voltage regulator,what is the difference between the input and the output voltage called?
(Multiple Choice)
4.7/5
(32)
Which of the following does not affect the quality of a power supply?
(Multiple Choice)
4.7/5
(37)
Which of the following is a disadvantage of a switching voltage regulator?
(Multiple Choice)
4.8/5
(31)
Since the ripple rejection of an IC voltage regulator is high
(Multiple Choice)
4.9/5
(22)
The most basic topology for switching regulators and one that always steps the voltage down is the
(Multiple Choice)
4.8/5
(33)
What is the condition called when the regulator will cut off the pass transistor and shut down the operation if the chip temperature becomes too high?
(Multiple Choice)
4.9/5
(35)
What is often used to improve the operation and efficiency of a series regulator?
(Multiple Choice)
4.7/5
(32)
An IC that contains a positive and a negative regulator in a single IC package is a
(Multiple Choice)
4.8/5
(38)
To avoid excessive power dissipation in a regulator's series pass transistor under shorted-load conditions,a designer can add
(Multiple Choice)
4.9/5
(34)
The quality of a power supply depends on its load regulation,line regulation,and output resistance.
(True/False)
4.7/5
(34)
What is the output pin found on some monolithic boost regulators called that provides a low impedance buffer and produces a rectangular output signal?
(Multiple Choice)
4.8/5
(35)
A power supply with a load regulation of less than 1 percent means that the load voltage varies less than 1 percent over the full range of load current.
(True/False)
4.9/5
(34)
The most widely used IC regulators are those with only three pins: one for the unregulated input voltage,one for the regulated output voltage,and one for ground.
(True/False)
4.9/5
(24)
The design technique or fundamental layout of a circuit is its ________.
(Multiple Choice)
4.9/5
(29)
Efficiency is equal to input power divided by output power and then multiplied by 100 percent.
(True/False)
4.9/5
(35)
Showing 1 - 20 of 49
Filters
- Essay(0)
- Multiple Choice(0)
- Short Answer(0)
- True False(0)
- Matching(0)