Question 1

Technician A says a prerequisite to accurate road testing analysis includes knowing what bands and clutches are applied in a particular gear range. Technician B says slipping conditions can be caused by a leaking hydraulic circuit. Who is correct?

Accepted Answer

A) A only 
B) B only 
C) both A and B 
D) neither A nor B

Question 2

If a transmission problem cannot be identified from an inspection or road test, a ____________________ test should be performed.

Accepted Answer

The answer of If a transmission problem cannot be identified...

Question 3

A technician is diagnosing a vehicle that does not crank over when the gear selector is in park or neutral but does crank when the gear selector is in Reverse and Drive. Technician A says the neutral safety switch could need adjustment. Technician B says the gear selector linkage could need adjustment. Who is correct?

Accepted Answer

A) A only 
B) B only 
C) both A and B 
D) neither A nor B

Question 4

Spool valves, springs, and other components of the valve body should be cleaned using a wiping rag or paper towel.

Accepted Answer

A) True 
 B)False

Question 5

Dark particles in the transmission fluid are an indication of worn ______.

Accepted Answer

A) clutches or bands 
B) thrust washers 
C) oil pump gears 
D) stator roller clutch

Question 6

The customer complains that the vehicle can roll when the transmission is in park. Also, the starter does not crank the engine over when the shifter is in park but will crank over when the shifter is halfway between neutral and drive. On a road test, when the transmission is shifted into manual low, the gear indicator is halfway between 1 and 2. Technician A says the parking pawl is broken and must be replaced. Technician B says the shifter linkage needs adjustment. Who is correct?

Accepted Answer

A) A only 
B) B only 
C) both A and B 
D) neither A nor B

Question 7

Technician A says all automatic transmissions use the same type of fluid. Technician B says each manufacturer specifies the proper type of fluid that should be used in their transmissions. Who is correct?

Accepted Answer

A) A only 
B) B only 
C) both A and B 
D) neither A nor B

Question 8

List five places where transmission leaks are common.

Accepted Answer

The answer of List five places where transmission leaks are...

Question 9

Low fluid levels can cause ______.

Accepted Answer

A) aerated fluid 
B) a buzzing noise inside the transmission 
C) slippage between shifts 
D) All the answers are correct.

Question 10

Where is the kickdown switch normally located?

Accepted Answer

The answer of Where is the kickdown switch normally located?...

Question 11

The ____________________ test checks the holding capacity of the torque converter stator's overrunning clutch and certain transmission clutches and bands.

Accepted Answer

The answer of The ____________________ test checks the holding capacity...

Question 12

Stall testing places should be conducted only if recommended by the manufacturer.

Accepted Answer

A) True 
 B)False

Question 13

Two technicians are trying to install a remanufactured transmission and torque converter in a vehicle. No matter how well they align the transmission with the engine, the transmission will not slide onto the dowel pins. Technician A says the pilot hub on the converter could be damaged. Technician B says one of the dowel pins could be out of round. Who is correct?

Accepted Answer

A) A only 
B) B only 
C) both A and B 
D) neither A nor B

Question 14

What does milky-colored ATF indicate?

Accepted Answer

The answer of What does milky-colored ATF indicate?...

Question 15

Swelling and bluing of the converter shell is a sign that the converter has been ______.

Accepted Answer

A) too hot 
B) too cold 
C) malfunctioning 
D) installed incorrectly

Question 16

If the noise is engine speed related and is present in all gears including park and neutral, the most probable source is the ______.

Accepted Answer

A) torque converter 
B) planetary gears 
C) transmission oil pump 
D) bands or servos

Question 17

Describe the stall test procedure.

Accepted Answer

The answer of Describe the stall test procedure....

Question 18

Dexron III transmission fluid can be used in all automatic transmissions.

Accepted Answer

A) True 
 B)False

Question 19

Technician A checks for worn or broken transmission mounts by prying on the transmission case with a pry bar while watching the mount. Technician B checks for worn or broken transmission mounts by running the engine at 1,500 rpm, with the transmission in drive and then in reverse , while he watches the torque reaction (movement)of the engine. Who is correct?

Accepted Answer

A) A only 
B) B only 
C) both A and B 
D) neither A nor B

Question 20

Technician A says the only positive way to identify the exact design of the transmission is by the shape of its oil pan. Technician B says identification numbers only identify the manufacturer and assembly date of the transmission. Who is correct?

Accepted Answer

A) A only 
B) B only 
C) both A and B 
D) neither A nor B

Exam 43: Automatic Transmission and Transaxle Service

Technician A says a prerequisite to accurate road testing analysis includes knowing what bands and clutches are applied in a particular gear range. Technician B says slipping conditions can be caused by a leaking hydraulic circuit. Who is correct?

If a transmission problem cannot be identified from an inspection or road test, a ____________________ test should be performed.

Spool valves, springs, and other components of the valve body should be cleaned using a wiping rag or paper towel.

Dark particles in the transmission fluid are an indication of worn ______.

Technician A says all automatic transmissions use the same type of fluid. Technician B says each manufacturer specifies the proper type of fluid that should be used in their transmissions. Who is correct?

List five places where transmission leaks are common.

Low fluid levels can cause ______.

Where is the kickdown switch normally located?

The ____________________ test checks the holding capacity of the torque converter stator's overrunning clutch and certain transmission clutches and bands.

Stall testing places should be conducted only if recommended by the manufacturer.

What does milky-colored ATF indicate?

Swelling and bluing of the converter shell is a sign that the converter has been ______.

If the noise is engine speed related and is present in all gears including park and neutral, the most probable source is the ______.

Describe the stall test procedure.

Dexron III transmission fluid can be used in all automatic transmissions.

Technician A says the only positive way to identify the exact design of the transmission is by the shape of its oil pan. Technician B says identification numbers only identify the manufacturer and assembly date of the transmission. Who is correct?