Question 1

-Refer to Figure 20-2.Which of these circuits is known as a peak detector?

Accepted Answer

A) (a) 
B) (b) 
C) (c) 
D) (d) 
A) (a) 
B) (b) 
C) (c) 
D) (d)

Question 2

The typical output for a normally operating thermocouple is in the range of 1 V to 10 V.

Accepted Answer

A) True 
 B)False

Question 3

Circuits that contain features such as common-mode rejection, isolation, gain, etc. are called:

Accepted Answer

A) signal conditioners. 
B) interfaces. 
C) thermocouples. 
D) none of the above. 
A) signal conditioners. 
B) interfaces. 
C) thermocouples. 
D) none of the above.

Question 4

The main purpose of an instrumentation amplifier is to amplify common mode Voltage.

Accepted Answer

A) True 
 B)False

Question 5

An active clamping circuit negates the opposite polarity 0.7 V peak by using two diodes in series.

Accepted Answer

A) True 
 B)False

Question 6

(d)
 
Figure $20 < 1$

-Refer to Figure 20-1 (a). If $\mathrm { R } _ { 1 } = \mathrm { R } _ { 2 } = 30 \mathrm { k \Omega }$ and the closed loop gain is 450 , the value of the external gain-setting resistor $R _ { G }$ is:

Accepted Answer

A)  $134 \mathrm { k } \Omega$ 
B)  $13.4 \Omega$ 
C)  $134 \Omega$ 
D)  none of the above. 
A)  $134 \mathrm { k } \Omega$ 
B)  $13.4 \Omega$ 
C)  $134 \Omega$ 
D)  none of the above.

Question 7

The ac value that is equal to the same dc heating effect is usually called:

Accepted Answer

A)  peak value. 
B)  heat value. 
C)  rms value. 
D)  average value. 
A)  peak value. 
B)  heat value. 
C)  rms value. 
D)  average value.

Question 8

Displacement transducers can be made using a variety of types of optical or electrical circuits.

Accepted Answer

A) True 
 B)False

Question 9

RTDs and thermistors both operate on the same principle of resistive changeW ith temperature.

Accepted Answer

A) True 
 B)False

Question 10

A voltage limiter that limits both positive and negative peaks uses two zener diodes connected anode to cathode.

Accepted Answer

A) True 
 B)False

Question 11

Which of the following is not a temperature sensor?

Accepted Answer

A) thermocouple 
B) thermistor 
C) resistance temperature detector 
D) triac 
A) thermocouple 
B) thermistor 
C) resistance temperature detector 
D) triac

Question 12

An instrumentation amplifier has a high:

Accepted Answer

A) output impedance. 
B) supply Voltage. 
C) CMRR. 
D) power gain. 
A) output impedance. 
B) supply Voltage. 
C) CMRR. 
D) power gain.

Question 13

-Refer to Figure 20-2 (d). If  gm=25 mS  and $\mathrm { R_L }  = 25 \mathrm { k } \Omega$
, the voltage gain would be:

Accepted Answer

A)   62.5 . 
B)   625 . 
C)   6.25 . 
D)  not enough information. 
A)   62.5 . 
B)   625 . 
C)   6.25 . 
D)  not enough information.

Question 14

(d)
 
Figure $20 < 1$

-Refer to Figure 20-1.W hich of these circuits is known as an isolation amplifier?

Accepted Answer

A) (a) 
B) (b) 
C) (c) 
D) (d) 
A) (a) 
B) (b) 
C) (c) 
D) (d)

Question 15

Strain gauges are used to detect minute changes in temperature.

Accepted Answer

A) True 
 B)False

Question 16

One of the key characteristics of an instrumentation amplifier is its low input impedance.

Accepted Answer

A) True 
 B)False

Question 17

(d)
 
Figure $20 < 1$

-Refer to Figure 20-1.W hich of these circuits is known as a constant-current source?

Accepted Answer

A) (a) 
B) (b) 
C) (c) 
D) (d) 
A) (a) 
B) (b) 
C) (c) 
D) (d)

Question 18

The OTA has a ________ input impedance and a ________ CMRR.

Accepted Answer

A) low, low 
B) high, low 
C) low, high 
D) high, high 
A) low, low 
B) high, low 
C) low, high 
D) high, high

Question 19

Basic analog physical parameters such as angular position, temperature, pressure, strain, and flow rate can be measured by What devices?

Accepted Answer

A) Transmissions 
B) Transducers 
C) Telemeters 
D) Transmitters 
A) Transmissions 
B) Transducers 
C) Telemeters 
D) Transmitters

Question 20

If an operational transconductance amplifier (OTA)is used as a nonlinear mixer and an audio signal is mixedW ith an RF signal, the outputW ill be a(n)________ signal.

Accepted Answer

A) amplitude modulated (AM) 
B) square Wave 
C) triangular Wave 
D) frequency modulated (FM) 
A) amplitude modulated (AM) 
B) square Wave 
C) triangular Wave 
D) frequency modulated (FM)

-Refer to Figure 20-2.Which of these circuits is known as a peak detector?

The typical output for a normally operating thermocouple is in the range of 1 V to 10 V.

Circuits that contain features such as common-mode rejection, isolation, gain, etc. are called:

The main purpose of an instrumentation amplifier is to amplify common mode Voltage.

An active clamping circuit negates the opposite polarity 0.7 V peak by using two diodes in series.

The ac value that is equal to the same dc heating effect is usually called:

Displacement transducers can be made using a variety of types of optical or electrical circuits.

RTDs and thermistors both operate on the same principle of resistive changeW ith temperature.

A voltage limiter that limits both positive and negative peaks uses two zener diodes connected anode to cathode.

Which of the following is not a temperature sensor?

An instrumentation amplifier has a high:

$-Refer to Figure 20-2 (d). If gm=25 mS and \mathrm { R_L } = 25 \mathrm { k } \Omega , the voltage gain would be:$ -Refer to Figure 20-2 (d). If gm=25 mS and $\mathrm { R_L } = 25 \mathrm { k } \Omega$ , the voltage gain would be:

(d) Figure $20 < 1$ -Refer to Figure 20-1.W hich of these circuits is known as an isolation amplifier?

Strain gauges are used to detect minute changes in temperature.

One of the key characteristics of an instrumentation amplifier is its low input impedance.

(d) Figure $20 < 1$ -Refer to Figure 20-1.W hich of these circuits is known as a constant-current source?

The OTA has a input impedance and a CMRR.

Basic analog physical parameters such as angular position, temperature, pressure, strain, and flow rate can be measured by What devices?

If an operational transconductance amplifier (OTA)is used as a nonlinear mixer and an audio signal is mixedW ith an RF signal, the outputW ill be a(n)________ signal.

Quantities and Units

Voltage, Current, and Resistance

Ohms Law, Energy, and Power

Series Circuits

Parallel Circuits

Series-Parallel Circuits

Magnetism and Electromagnetism

Introduction to Alternating Current and Voltage

Capacitors

Rc Circuits

Inductors

Rl Circuits

Rlc Circuits and Resonance

Time Response of Reactive Circuits

Transformers

Regulators, Filters, and Op-Amps

Filters

Exam 17: Understanding Transducers, Sensors, and Conversion in Industrial Processes

-Refer to Figure 20-2.Which of these circuits is known as a peak detector?

The typical output for a normally operating thermocouple is in the range of 1 V to 10 V.

Circuits that contain features such as common-mode rejection, isolation, gain, etc. are called:

The main purpose of an instrumentation amplifier is to amplify common mode Voltage.

An active clamping circuit negates the opposite polarity 0.7 V peak by using two diodes in series.

(d) Figure 20<120 < 120<1 -Refer to Figure 20-1 (a). If R1=R2=30kΩ\mathrm { R } _ { 1 } = \mathrm { R } _ { 2 } = 30 \mathrm { k \Omega }R1​=R2​=30kΩ and the closed loop gain is 450 , the value of the external gain-setting resistor RGR _ { G }RG​ is:

The ac value that is equal to the same dc heating effect is usually called:

Displacement transducers can be made using a variety of types of optical or electrical circuits.

RTDs and thermistors both operate on the same principle of resistive changeW ith temperature.

A voltage limiter that limits both positive and negative peaks uses two zener diodes connected anode to cathode.

Which of the following is not a temperature sensor?

An instrumentation amplifier has a high:

-Refer to Figure 20-2 (d). If gm=25 mS and RL=25kΩ\mathrm { R_L } = 25 \mathrm { k } \OmegaRL​=25kΩ , the voltage gain would be:

(d) Figure 20<120 < 120<1 -Refer to Figure 20-1.W hich of these circuits is known as an isolation amplifier?

Strain gauges are used to detect minute changes in temperature.

One of the key characteristics of an instrumentation amplifier is its low input impedance.

(d) Figure 20<120 < 120<1 -Refer to Figure 20-1.W hich of these circuits is known as a constant-current source?

The OTA has a ________ input impedance and a ________ CMRR.

Basic analog physical parameters such as angular position, temperature, pressure, strain, and flow rate can be measured by What devices?

If an operational transconductance amplifier (OTA)is used as a nonlinear mixer and an audio signal is mixedW ith an RF signal, the outputW ill be a(n)________ signal.

Quantities and Units

Voltage, Current, and Resistance

Ohms Law, Energy, and Power

Series Circuits

Parallel Circuits

Series-Parallel Circuits

Magnetism and Electromagnetism

Introduction to Alternating Current and Voltage

Capacitors

Rc Circuits

Inductors

Rl Circuits

Rlc Circuits and Resonance

Time Response of Reactive Circuits

Transformers

Regulators, Filters, and Op-Amps

Filters

$-Refer to Figure 20-2 (d). If gm=25 mS and \mathrm { R_L } = 25 \mathrm { k } \Omega , the voltage gain would be:$ -Refer to Figure 20-2 (d). If gm=25 mS and $\mathrm { R_L } = 25 \mathrm { k } \Omega$ , the voltage gain would be:

(d) Figure $20 < 1$ -Refer to Figure 20-1.W hich of these circuits is known as an isolation amplifier?

(d) Figure $20 < 1$ -Refer to Figure 20-1.W hich of these circuits is known as a constant-current source?

The OTA has a input impedance and a CMRR.