Question 1

Which UEM/CLI command is used to verify the FC ports designated as synchronous on the SPs?

Accepted Answer

A)  /remote/sys show -lc 
B)  /remote/sys show -detail 
C)  /remote/sys show -summary 
D)  /remote/sys show -sp 
A)  /remote/sys show -lc 
B)  /remote/sys show -detail 
C)  /remote/sys show -summary 
D)  /remote/sys show -sp

Question 2

What is a benefit of Dell EMC Unity XT Series dynamic pools?

Accepted Answer

A)  Reduced time to rebuild a failed drive 
B)  Improved access to data resident on the drive tiers 
C)  Protects written data from deletion or modification 
D)  Enables throughput and bandwidth throttling 
A)  Reduced time to rebuild a failed drive 
B)  Improved access to data resident on the drive tiers 
C)  Protects written data from deletion or modification 
D)  Enables throughput and bandwidth throttling

Question 3

A large data center is hosting storage protection solutions for multiple companies. This solution is accomplished by the hosting organization's ability to consolidate data to an environment with two VNX arrays. How many RecoverPoint clusters can be used in this environment?

Accepted Answer

A)  12 clusters, assuming each LUN is attached to only one cluster at a time 
B)  6 clusters, assuming only vRPAs are used 
C)  12 clusters, assuming each LUN is replicated across the clusters 
D)  6 clusters, assuming each LUN is attached to only one cluster at a time 
A)  12 clusters, assuming each LUN is attached to only one cluster at a time 
B)  6 clusters, assuming only vRPAs are used 
C)  12 clusters, assuming each LUN is replicated across the clusters 
D)  6 clusters, assuming each LUN is attached to only one cluster at a time

Question 4

What is a characteristic of FAST VP?

Accepted Answer

A)  User can enable or disable FAST VP at the LUN level 
B)  FAST VP optimizes data placement by moving 1GB slices between disk tiers 
C)  Once enabled, FAST VP data relocation runs in background runs in background at all times 
D)  User can set the FAST VP data relocation rate 
A)  User can enable or disable FAST VP at the LUN level 
B)  FAST VP optimizes data placement by moving 1GB slices between disk tiers 
C)  Once enabled, FAST VP data relocation runs in background runs in background at all times 
D)  User can set the FAST VP data relocation rate

Question 5

Which type of Consistency Group requires a primary and secondary production copy?

Accepted Answer

A)  MetroPoint 
B)  Synchronous 
C)  Distributed 
D)  Asynchronous 
A)  MetroPoint 
B)  Synchronous 
C)  Distributed 
D)  Asynchronous

Question 6

A company is currently using RecoverPoint/SE in their environment. They have purchased a VMAX which will be deployed to replace the VNX splitter at one site only. What must be done before they can use the VMAX with RecoverPoint (RP)?

Accepted Answer

A)  Use RecoverPoint Deployment Manager to convert from RP/SE to RP/EX or RP/CL 
B)  Use Unisphere for RecoverPoint to convert from RP/SE to RP/EX or RP/CL 
C)  Purchase and use a VMAX at the other site 
D)  Deploy an updated splitter on the existing array that will function with the new VMAX splitter 
A)  Use RecoverPoint Deployment Manager to convert from RP/SE to RP/EX or RP/CL 
B)  Use Unisphere for RecoverPoint to convert from RP/SE to RP/EX or RP/CL 
C)  Purchase and use a VMAX at the other site 
D)  Deploy an updated splitter on the existing array that will function with the new VMAX splitter

Question 7

Which IP connection characteristic is used only for file-based storage configurations on Dell EMC Unity XT?

Accepted Answer

A)  Link aggregation 
B)  VLAN tagging 
C)  Bandwidth throttle 
D)  Network latency 
A)  Link aggregation 
B)  VLAN tagging 
C)  Bandwidth throttle 
D)  Network latency

Question 8

Once a device is in an Open Replicator RecoverPoint session, what must be done in order to make configuration changes to that device?

Accepted Answer

A)  Disable the Configuration Group 
B)  Pause the Configuration Group 
C)  Unmap the device 
D)  Unmask the device 
A)  Disable the Configuration Group 
B)  Pause the Configuration Group 
C)  Unmap the device 
D)  Unmask the device

Question 9

What is the maximum number of file system snapshots that are supported by Unity?

Accepted Answer

A)  16 
B)  96 
C)  256 
D)  512 
A)  16 
B)  96 
C)  256 
D)  512

Question 10

What is a consideration when designing a replication solution using the native Dell EMC Unity XT replication feature?

Accepted Answer

A)  Asynchronous remote replication supports replication to up to two remote Dell EMC Unity XT systems 
B)  Synchronous remote replication supports replication to up to two remote Dell EMC Unity XT systems 
C)  Synchronous remote replication supports replication to up to one remote Dell EMC Unity XT systems 
D)  Asynchronous remote replication supports replication to up to one remote Dell EMC Unity XT systems 
A)  Asynchronous remote replication supports replication to up to two remote Dell EMC Unity XT systems 
B)  Synchronous remote replication supports replication to up to two remote Dell EMC Unity XT systems 
C)  Synchronous remote replication supports replication to up to one remote Dell EMC Unity XT systems 
D)  Asynchronous remote replication supports replication to up to one remote Dell EMC Unity XT systems

Question 11

A company is currently using RecoverPoint/SE in their environment. They have purchased a VMAX which will be deployed to replace a VNX splitter at one site only. What must be done before they can use the VMAX with RecoverPoint (RP)?

Accepted Answer

A)  Obtain an updated license that will support RP/EX or RP/CL 
B)  Use Unisphere for RecoverPoint to convert from RP/SE to RP/EX or RP/CL 
C)  Purchase and use a VMAX at the other site 
D)  Deploy an updated splitter on the existing array that will function with the new VMAX splitter 
A)  Obtain an updated license that will support RP/EX or RP/CL 
B)  Use Unisphere for RecoverPoint to convert from RP/SE to RP/EX or RP/CL 
C)  Purchase and use a VMAX at the other site 
D)  Deploy an updated splitter on the existing array that will function with the new VMAX splitter

Question 12

When is the Open Replicator RecoverPoint session created for each production volume in the Consistency Group (CG)?

Accepted Answer

A)  CG is enabled 
B)  CG is created 
C)  LUN is attached to the splitter 
D)  LUN is added to an RSET 
A)  CG is enabled 
B)  CG is created 
C)  LUN is attached to the splitter 
D)  LUN is added to an RSET

Question 13

Which UEM/CLI command is used to verify the FC ports designated as synchronous on the SPs?

Accepted Answer

A)  /remote/sys show -fc 
B)  /remote/sys show -detail 
C)  /remote/sys show -summary 
D)  /remote/sys show -sp 
A)  /remote/sys show -fc 
B)  /remote/sys show -detail 
C)  /remote/sys show -summary 
D)  /remote/sys show -sp

Question 14

What would cause a volume sweep to occur?

Accepted Answer

A)  A new Replication Set is added to an enabled Consistency Group 
B)  A previously disabled splitter is enabled 
C)  A Replication Set is removed from a disabled Consistency Group 
D)  A previously enabled splitter is disabled 
A)  A new Replication Set is added to an enabled Consistency Group 
B)  A previously disabled splitter is enabled 
C)  A Replication Set is removed from a disabled Consistency Group 
D)  A previously enabled splitter is disabled

Question 15

What is a characteristic of the iSCSI interface on Dell EMC Unity XT storage arrays?

Accepted Answer

A)  IQN aliases can be created optionally after the iSCSI interface is created. 
B)  IQN aliases are associated with an iSCSI interface. 
C)  IQNs are associated with a network port. 
D)  An iSCSI interface can be created with both an IPv4 and IPv6 IP address. 
A)  IQN aliases can be created optionally after the iSCSI interface is created. 
B)  IQN aliases are associated with an iSCSI interface. 
C)  IQNs are associated with a network port. 
D)  An iSCSI interface can be created with both an IPv4 and IPv6 IP address.

Question 16

Which storage objects support Advanced Deduplication?

Accepted Answer

A)  VMFS datastores and VVols 
B)  Thin LUNs and thick LUNs 
C)  Thick LUNs and VVols 
D)  Thin LUNs and thin VMFS datastores 
A)  VMFS datastores and VVols 
B)  Thin LUNs and thick LUNs 
C)  Thick LUNs and VVols 
D)  Thin LUNs and thin VMFS datastores

Question 17

A storage administrator wants to asynchronously replicate a compressed LUN from the primary site to a Unity at the secondary site. Which statement describes this operation?

Accepted Answer

A)  Replication of compresses data is controlled by the bandwidth throttle setting. 
B)  By default, replication compresses data sent to the destination. 
C)  The source data is uncompressed, then replicated to the destination. 
D)  The source data is replicated to the destination, then uncompressed. 
A)  Replication of compresses data is controlled by the bandwidth throttle setting. 
B)  By default, replication compresses data sent to the destination. 
C)  The source data is uncompressed, then replicated to the destination. 
D)  The source data is replicated to the destination, then uncompressed.

Question 18

What determines the fault characteristics of a disk group?

Accepted Answer

A)  Drive speed 
B)  Stripe width 
C)  Drive type 
D)  D@RE 
A)  Drive speed 
B)  Stripe width 
C)  Drive type 
D)  D@RE

Question 19

The preferred production interface is active. What does the Dell EMC Unity XT system do once a NAS Server starts outbound traffic to an external service?

Accepted Answer

A)  Uses the backup interface 
B)  Initiates NAS Server failover 
C)  Uses the active production interface 
D)  Enables Packet Reflect 
A)  Uses the backup interface 
B)  Initiates NAS Server failover 
C)  Uses the active production interface 
D)  Enables Packet Reflect

Question 20

A Storage administrator would like to increase the capacity of the FAST Cache by 400 GB. The current configuration consists of two 400 GB SAS Flash 2 drives. Which solution should be recommended for expanding the FAST Cache?

Accepted Answer

A)  Two 200 GB SAS Flash 2 drives 
B)  Two 400 GB SAS Flash 2 drives 
C)  Four 200 GB SAS Flash 3 drives 
D)  One 400 GB SAS Flash 2 drive 
A)  Two 200 GB SAS Flash 2 drives 
B)  Two 400 GB SAS Flash 2 drives 
C)  Four 200 GB SAS Flash 3 drives 
D)  One 400 GB SAS Flash 2 drive

Which UEM/CLI command is used to verify the FC ports designated as synchronous on the SPs?

What is a benefit of Dell EMC Unity XT Series dynamic pools?

A large data center is hosting storage protection solutions for multiple companies. This solution is accomplished by the hosting organization's ability to consolidate data to an environment with two VNX arrays. How many RecoverPoint clusters can be used in this environment?

What is a characteristic of FAST VP?

Which type of Consistency Group requires a primary and secondary production copy?

A company is currently using RecoverPoint/SE in their environment. They have purchased a VMAX which will be deployed to replace the VNX splitter at one site only. What must be done before they can use the VMAX with RecoverPoint (RP)?

Which IP connection characteristic is used only for file-based storage configurations on Dell EMC Unity XT?

Once a device is in an Open Replicator RecoverPoint session, what must be done in order to make configuration changes to that device?

What is the maximum number of file system snapshots that are supported by Unity?

What is a consideration when designing a replication solution using the native Dell EMC Unity XT replication feature?

A company is currently using RecoverPoint/SE in their environment. They have purchased a VMAX which will be deployed to replace a VNX splitter at one site only. What must be done before they can use the VMAX with RecoverPoint (RP)?

When is the Open Replicator RecoverPoint session created for each production volume in the Consistency Group (CG)?

Which UEM/CLI command is used to verify the FC ports designated as synchronous on the SPs?

What would cause a volume sweep to occur?

What is a characteristic of the iSCSI interface on Dell EMC Unity XT storage arrays?

Which storage objects support Advanced Deduplication?

A storage administrator wants to asynchronously replicate a compressed LUN from the primary site to a Unity at the secondary site. Which statement describes this operation?

What determines the fault characteristics of a disk group?

The preferred production interface is active. What does the Dell EMC Unity XT system do once a NAS Server starts outbound traffic to an external service?

A Storage administrator would like to increase the capacity of the FAST Cache by 400 GB. The current configuration consists of two 400 GB SAS Flash 2 drives. Which solution should be recommended for expanding the FAST Cache?

VPLEX Specialist for Implementation Engineers

XtremIO Solutions Specialist Exam for Implementation Engineers

RecoverPoint Specialist for Implementation Engineers

XtremIO Solutions and Design Specialist Exam for Technology Architects

Isilon Solutions and Design Specialist for Technology Architects

VPLEX Specialist Exam for Storage Administrators

RecoverPoint Specialist for Storage Administrators

Backup and Recovery - Avamar Specialist for Implementation Engineers

Backup Recovery - Avamar Specialist for Storage Administrators

ScaleIO 1.x Server-Based SAN

Filters

Exam 4: Unity Solutions Specialist Exam for Implementation Engineers

Which UEM/CLI command is used to verify the FC ports designated as synchronous on the SPs?

What is a benefit of Dell EMC Unity XT Series dynamic pools?

A large data center is hosting storage protection solutions for multiple companies. This solution is accomplished by the hosting organization's ability to consolidate data to an environment with two VNX arrays. How many RecoverPoint clusters can be used in this environment?

What is a characteristic of FAST VP?

Which type of Consistency Group requires a primary and secondary production copy?

A company is currently using RecoverPoint/SE in their environment. They have purchased a VMAX which will be deployed to replace the VNX splitter at one site only. What must be done before they can use the VMAX with RecoverPoint (RP)?

Which IP connection characteristic is used only for file-based storage configurations on Dell EMC Unity XT?

Once a device is in an Open Replicator RecoverPoint session, what must be done in order to make configuration changes to that device?

What is the maximum number of file system snapshots that are supported by Unity?

What is a consideration when designing a replication solution using the native Dell EMC Unity XT replication feature?

A company is currently using RecoverPoint/SE in their environment. They have purchased a VMAX which will be deployed to replace a VNX splitter at one site only. What must be done before they can use the VMAX with RecoverPoint (RP)?

When is the Open Replicator RecoverPoint session created for each production volume in the Consistency Group (CG)?

Which UEM/CLI command is used to verify the FC ports designated as synchronous on the SPs?

What would cause a volume sweep to occur?

What is a characteristic of the iSCSI interface on Dell EMC Unity XT storage arrays?

Which storage objects support Advanced Deduplication?

A storage administrator wants to asynchronously replicate a compressed LUN from the primary site to a Unity at the secondary site. Which statement describes this operation?

What determines the fault characteristics of a disk group?

The preferred production interface is active. What does the Dell EMC Unity XT system do once a NAS Server starts outbound traffic to an external service?

A Storage administrator would like to increase the capacity of the FAST Cache by 400 GB. The current configuration consists of two 400 GB SAS Flash 2 drives. Which solution should be recommended for expanding the FAST Cache?

VPLEX Specialist for Implementation Engineers

XtremIO Solutions Specialist Exam for Implementation Engineers

RecoverPoint Specialist for Implementation Engineers

XtremIO Solutions and Design Specialist Exam for Technology Architects

Isilon Solutions and Design Specialist for Technology Architects

VPLEX Specialist Exam for Storage Administrators

RecoverPoint Specialist for Storage Administrators

Backup and Recovery - Avamar Specialist for Implementation Engineers

Backup Recovery - Avamar Specialist for Storage Administrators

ScaleIO 1.x Server-Based SAN

Filters