Question 1

All of the following statements are true with respect to end play except:

Accepted Answer

A)  End play also measures the amount of free play in the geartrain inside the transmission. 
B)  It is checked by placing the transmission so that the input shaft is horizontal. 
C)  It can be measured using a dial indicator that is placed on the end of the input shaft. 
D)  Depending on the transmission, either the input shaft will need to be pulled up or the output shaft will need to be pushed up. 
A)  End play also measures the amount of free play in the geartrain inside the transmission. 
B)  It is checked by placing the transmission so that the input shaft is horizontal. 
C)  It can be measured using a dial indicator that is placed on the end of the input shaft. 
D)  Depending on the transmission, either the input shaft will need to be pulled up or the output shaft will need to be pushed up. B

Question 2

Which of the following can be worn by metal check balls?

Accepted Answer

A)  Valve body 
B)  Spool valves 
C)  Separator plate 
D)  Both A and C 
A)  Valve body 
B)  Spool valves 
C)  Separator plate 
D)  Both A and C D

Question 3

When installing a transmission, which of these is an alternate to using a support tool?

Accepted Answer

A)  Weld the reaction gear and the output shaft together. 
B)  Use thread locking compound to glue the reaction ring gear to the output shaft. 
C)  Install the output shaft into the transmission with the vehicle speed sensor reluctor wheel intact. 
D)  Remove all lubrication from the output shaft and the reaction gear so that they are held together by friction. 
A)  Weld the reaction gear and the output shaft together. 
B)  Use thread locking compound to glue the reaction ring gear to the output shaft. 
C)  Install the output shaft into the transmission with the vehicle speed sensor reluctor wheel intact. 
D)  Remove all lubrication from the output shaft and the reaction gear so that they are held together by friction. B

Question 4

When installing manual shaft seals:

Accepted Answer

A)  do not use a specialty driver. 
B)  it is easier if the manual shaft is already installed. 
C)  do not lubricate the sealing edge. 
D)  make sure that the manual shaft seal is straight as it is installed. 
A)  do not use a specialty driver. 
B)  it is easier if the manual shaft is already installed. 
C)  do not lubricate the sealing edge. 
D)  make sure that the manual shaft seal is straight as it is installed.

Question 5

Where should compressed air should be used to ensure each fluid passage is clear and unobstructed?

Accepted Answer

A)  Transmission case 
B)  Valve body 
C)  Input and output shafts 
D)  All of the above 
A)  Transmission case 
B)  Valve body 
C)  Input and output shafts 
D)  All of the above

Question 6

Tech A says that a small amount of epoxy can be used to hold thrust washers in place. Tech B says that a small amount of transmission assembly lubricant can be used to hold check balls in place during transmission assembly. Who is correct?

Accepted Answer

A)  Tech A 
B)  Tech B 
C)  Both A and B 
D)  Neither A nor B 
A)  Tech A 
B)  Tech B 
C)  Both A and B 
D)  Neither A nor B

Question 7

All of the following statements are true with respect to final transmission assembly except:

Accepted Answer

A)  Any clutches that are being installed should be soaked in the correct automatic transmission fluid for at least 15 minutes before assembling the transmission. 
B)  All components should be lubricated with the correct automatic transmission fluid, or transmission assembly lube, as they are installed in the transmission. 
C)  Force the transmission parts together as they do not go together easily. 
D)  Certain components may need to be frozen in order to install them into the transmission. 
A)  Any clutches that are being installed should be soaked in the correct automatic transmission fluid for at least 15 minutes before assembling the transmission. 
B)  All components should be lubricated with the correct automatic transmission fluid, or transmission assembly lube, as they are installed in the transmission. 
C)  Force the transmission parts together as they do not go together easily. 
D)  Certain components may need to be frozen in order to install them into the transmission.

Question 8

Tech A states that proper transmission assembly is critical for the repair job to be successful. Tech B says that all components of the automatic transmission should have been rebuilt and/or inspected before the reassembly process begins. Who is correct?

Accepted Answer

A)  Tech A 
B)  Tech B 
C)  Both A and B 
D)  Neither A nor B 
A)  Tech A 
B)  Tech B 
C)  Both A and B 
D)  Neither A nor B

Question 9

Which of the following should be installed after the planetary carrier is installed?

Accepted Answer

A)  Low/reverse clutch components. 
B)  Sun gear. 
C)  2-4 brake band. 
D)  Rear thrust bearing and output shaft. 
A)  Low/reverse clutch components. 
B)  Sun gear. 
C)  2-4 brake band. 
D)  Rear thrust bearing and output shaft.

Question 10

Technician A says all components of the oil delivery circuit in an automatic transmission must be inspected for debris during a transmission rebuild. Technician B says that this is not necessary since all debris would be captured by the transmission filter. Who is correct?

Accepted Answer

A)  Technician A 
B)  Technician B 
C)  Both A and B 
D)  Neither A nor B 
A)  Technician A 
B)  Technician B 
C)  Both A and B 
D)  Neither A nor B

Question 11

Technician A says that transmission end play can be adjusted with select fit thrust washers. Technician B says that transmission end play should be measured after the front pump is installed. Who is correct?

Accepted Answer

A)  Technician A 
B)  Technician B 
C)  Both A and B 
D)  Neither A nor B 
A)  Technician A 
B)  Technician B 
C)  Both A and B 
D)  Neither A nor B

Question 12

Tech A states that clutches should be soaked in the correct transmission fluid before installing them into transmission. Tech B states that clutches should be soaked for at least 15 minutes before installation. Who is correct?

Accepted Answer

A)  Tech A 
B)  TechB 
C)  Both A and B 
D)  Neither A nor B 
A)  Tech A 
B)  TechB 
C)  Both A and B 
D)  Neither A nor B

Question 13

When installing the reaction planetary carrier down into the reaction ring gear, what should be done for the carrier to fit down into the transmission?

Accepted Answer

A)  Rotate the planet gears. 
B)  Apply extra lubrication. 
C)  Apply mild force to make them fit. 
D)  Rotate the reaction ring gear. 
A)  Rotate the planet gears. 
B)  Apply extra lubrication. 
C)  Apply mild force to make them fit. 
D)  Rotate the reaction ring gear.

Question 14

Many internal automatic transmission bushings are a split ring bushing that must be installed carefully to prevent splitting the new bearing apart.

Accepted Answer

A) True 
 B)False

Question 15

What are the best tools to install a new transmission seal in the extension housing?

Accepted Answer

A)  Seal installation tool and hammer 
B)  Hammer and drift punch 
C)  Hydraulic press and flat steel plate 
D)  A large socket and a brass hammer 
A)  Seal installation tool and hammer 
B)  Hammer and drift punch 
C)  Hydraulic press and flat steel plate 
D)  A large socket and a brass hammer

Question 16

If thrust bearings or washers are worn, ______ movement of components inside the automatic transmission will be allowed, affecting their operation.

Accepted Answer

A)  Parallel 
B)  Lateral 
C)  Horizontal 
D)  None of the above 
A)  Parallel 
B)  Lateral 
C)  Horizontal 
D)  None of the above

Question 17

Which of the following should be installed after the planetary carrier is installed?

Accepted Answer

A)  Low/reverse clutch components. 
B)  Sun gear. 
C)  2-4 brake band. 
D)  Rear thrust bearing and output shaft. 
A)  Low/reverse clutch components. 
B)  Sun gear. 
C)  2-4 brake band. 
D)  Rear thrust bearing and output shaft.

Question 18

Tech A states that clutches should be soaked in the correct transmission fluid before installing them into transmission. Tech B states that clutches should be soaked for at least 15 minutes before installation. Who is correct?

Accepted Answer

A)  Tech A 
B)  TechB 
C)  Both A and B 
D)  Neither A nor B 
A)  Tech A 
B)  TechB 
C)  Both A and B 
D)  Neither A nor B

Question 19

Which of the following terms refers to the amount that a bearing is able to move before hitting the bearing race?

Accepted Answer

A)  Crush fit 
B)  Free play 
C)  Bearing force load 
D)  Preload 
A)  Crush fit 
B)  Free play 
C)  Bearing force load 
D)  Preload

Question 20

When installing a transmission, which of these is an alternate to using a support tool?

Accepted Answer

A)  Weld the reaction gear and the output shaft together. 
B)  Use thread locking compound to glue the reaction ring gear to the output shaft. 
C)  Install the output shaft into the transmission with the vehicle speed sensor reluctor wheel intact. 
D)  Remove all lubrication from the output shaft and the reaction gear so that they are held together by friction. 
A)  Weld the reaction gear and the output shaft together. 
B)  Use thread locking compound to glue the reaction ring gear to the output shaft. 
C)  Install the output shaft into the transmission with the vehicle speed sensor reluctor wheel intact. 
D)  Remove all lubrication from the output shaft and the reaction gear so that they are held together by friction.

Exam 18: Transmission Reassembly

All of the following statements are true with respect to end play except:

Which of the following can be worn by metal check balls?

When installing a transmission, which of these is an alternate to using a support tool?

When installing manual shaft seals:

Where should compressed air should be used to ensure each fluid passage is clear and unobstructed?

Tech A says that a small amount of epoxy can be used to hold thrust washers in place. Tech B says that a small amount of transmission assembly lubricant can be used to hold check balls in place during transmission assembly. Who is correct?

All of the following statements are true with respect to final transmission assembly except:

Tech A states that proper transmission assembly is critical for the repair job to be successful. Tech B says that all components of the automatic transmission should have been rebuilt and/or inspected before the reassembly process begins. Who is correct?

Which of the following should be installed after the planetary carrier is installed?

Technician A says all components of the oil delivery circuit in an automatic transmission must be inspected for debris during a transmission rebuild. Technician B says that this is not necessary since all debris would be captured by the transmission filter. Who is correct?

Technician A says that transmission end play can be adjusted with select fit thrust washers. Technician B says that transmission end play should be measured after the front pump is installed. Who is correct?

Tech A states that clutches should be soaked in the correct transmission fluid before installing them into transmission. Tech B states that clutches should be soaked for at least 15 minutes before installation. Who is correct?

When installing the reaction planetary carrier down into the reaction ring gear, what should be done for the carrier to fit down into the transmission?

Many internal automatic transmission bushings are a split ring bushing that must be installed carefully to prevent splitting the new bearing apart.

What are the best tools to install a new transmission seal in the extension housing?

If thrust bearings or washers are worn, ______ movement of components inside the automatic transmission will be allowed, affecting their operation.

Which of the following should be installed after the planetary carrier is installed?

Tech A states that clutches should be soaked in the correct transmission fluid before installing them into transmission. Tech B states that clutches should be soaked for at least 15 minutes before installation. Who is correct?

Which of the following terms refers to the amount that a bearing is able to move before hitting the bearing race?

When installing a transmission, which of these is an alternate to using a support tool?

Strategy-Based Diagnostics

Safety

Basic Tools and Precision Measuring

Fasteners and Thread Repair

Vehicle, Customer, and Service Information

Automatic Transmission Fundamentals

Transmission Components

Hydraulic Fundamentals

Torque Converter Principles

Hydraulically Controlled Transmission

Electronically Controlled Transmission

In-Vehicle Transmission Repairs

Transmission Removal

Transmission Disassembly

Hydraulic System Rebuilding

Gear Train Rebuilding

Valve Body and Electric Service

Transmission Reinstallation

Dual Clutch Transmissions

Continuously Variable Transmissions

Hybrid Transmissions

Honda Transmissions

Chrysler 6 Speed 62te Transmission

6t40 6f35 Transmission

Zf 9hp Chrysler 948te Transmission

Ford 6r60 Zf6hp26

Allison 1000 and 2000 Series Transmissions

Filters