Question 1

What cutting fluid should be used when drilling aluminum?

Accepted Answer

A)  lard 
B)  dry 
C)  soluble oil 
D)  kerosene 
A)  lard 
B)  dry 
C)  soluble oil 
D)  kerosene

Question 2

Convert 10 lB. to Newton meters

Accepted Answer

A)  1.356 
B)  2.623 
C)  13.56 
D)  26.23 
A)  1.356 
B)  2.623 
C)  13.56 
D)  26.23

Question 3

When tapping brass, what cutting fluid is recommended?

Accepted Answer

A)  lard 
B)  soluble oil 
C)  none 
D)  kerosene 
A)  lard 
B)  soluble oil 
C)  none 
D)  kerosene

Question 4

Which of the following values is the odd one out?

Accepted Answer

A)  14.7 psi 
B)  101.3 kPa 
C)  29.92 inches Hg 
D)  3 bar 
A)  14.7 psi 
B)  101.3 kPa 
C)  29.92 inches Hg 
D)  3 bar

Question 5

The closest metric wrench size to a standard 3/4 inch wrench is

Accepted Answer

A)  15 mm 
B)  18 mm 
C)  19 mm 
D)  21 mm 
A)  15 mm 
B)  18 mm 
C)  19 mm 
D)  21 mm

Question 6

What is the correct point angle of a drill bit designed for drilling steel?

Accepted Answer

A)  90 degrees 
B)  100 degrees 
C)  120 degrees 
D)  150 degrees 
A)  90 degrees 
B)  100 degrees 
C)  120 degrees 
D)  150 degrees

Question 7

Which type of hammer would NOT be found in a truck technician's tool box?

Accepted Answer

A)  ball peen 
B)  cross peen 
C)  claw 
D)  rubber mallet 
A)  ball peen 
B)  cross peen 
C)  claw 
D)  rubber mallet

Question 8

If you were required to remove a seized hex nut from a threaded stud, which of the following would be the best choice of tool?

Accepted Answer

A)  pipe wrench 
B)  adjustable wrench 
C)  hex wrench 
D)  double-hex wrench 
A)  pipe wrench 
B)  adjustable wrench 
C)  hex wrench 
D)  double-hex wrench

Question 9

Which of the following instruments is designed to measure rotational speed?

Accepted Answer

A)  dial bore gauge 
B)  dial indicator 
C)  load rotor 
D)  tachometer 
A)  dial bore gauge 
B)  dial indicator 
C)  load rotor 
D)  tachometer

Question 10

Which of the following tools is capable of performing inside, outside, and depth measurements?

Accepted Answer

A)  dial indicator 
B)  digital calipers 
C)  combination square 
D)  inside micrometer 
A)  dial indicator 
B)  digital calipers 
C)  combination square 
D)  inside micrometer

Exam 2: Hand and Shop Tools, Precision Tools, and Units of Measurement

What cutting fluid should be used when drilling aluminum?

Convert 10 lB. to Newton meters

When tapping brass, what cutting fluid is recommended?

Which of the following values is the odd one out?

The closest metric wrench size to a standard 3/4 inch wrench is

What is the correct point angle of a drill bit designed for drilling steel?

Which type of hammer would NOT be found in a truck technician's tool box?

If you were required to remove a seized hex nut from a threaded stud, which of the following would be the best choice of tool?

Which of the following instruments is designed to measure rotational speed?

Which of the following tools is capable of performing inside, outside, and depth measurements?

Introduction

Personal and Safety Awareness

Engine Basics

History of the Heat Engine

Power

Engine Powertrain Components

Engine Feedback Assembly

Engine Housing Components

Engine Lubrication Systems

Engine Cooling Systems

Engine Breathing

Engine Retarders

Servicing and Maintenance

Engine Removal, Disassembly, Cleaning,

Diesel Engine Run- in and Performance Testing

Chemistry and Combustion

Diesel Fuel Characteristics

Fuel Subsystems

Fuel Injection Basics and Governor Principles

Injector Nozzles

Port-Helix Metering Injection Pumps

Inlet-Metering Rotary Distributor Pumps

Sleeve-Metering Rotary Distributor Pumps

Single-Actuator Eui Systems

Dual-Actuator Eui Systems

Heui Fuel Systems

Electronic Unit Pump Eup Systems

Cummins Hpi-Tp

Common Rail Systems

Amplified Common Rail Systems

Review of Electrical and Electronics Fundamentals

Vehicle Computer Systems

Ests and Siss

Electrical Wiring, Connector Terminal Repair

Multiplexing

The Connected Vehicle

Natural Gas, Propane, and Biodiesel Fuels

High Voltage Electricity

Hybrid and Hydrogen Fuel Cell Drivetrains

Electric Powertrains

Bosch Edc Systems

Caterpillar Engine Management Systems

Cummins Management Systems

Detroit Diesel Electronic Controls Ddec

Navistar Diamond Logic

Paccar Engine Management Systems

Volvo and Mack Engine Management

Emissions Management

Servicing Maintenance of Exhaust Aftertreatment Systems

Failure Analysis

Troubleshooting and Diagnostics

Filters