Question 1

Which generator would you prefer for feeding long D.C. transmission lines ?

Accepted Answer

A) Series generator 
B) Shunt generator 
C) Over compound generator 
D) Flat compound generator 
A) Series generator 
B) Shunt generator 
C) Over compound generator 
D) Flat compound generator C

Question 2

Shunt generators are most suited for stable parallel operation because of their

Accepted Answer

A) rising voltage characteristics 
B) identical voltage characteristics 
C) drooping voltage characteristics 
D) linear voltage characteristics 
A) rising voltage characteristics 
B) identical voltage characteristics 
C) drooping voltage characteristics 
D) linear voltage characteristics C

Question 3

The essential condition for parallel operation of two D.C. generators is that they have '

Accepted Answer

A) same kW rating 
B) the same operation r.p.m. 
C) the same drooping voltage charac-teristics 
D) same percentage regulation 
A) same kW rating 
B) the same operation r.p.m. 
C) the same drooping voltage charac-teristics 
D) same percentage regulation C

Question 4

The open circuit voltage of a compound generator is 250 V. At full load the terminal voltage

Accepted Answer

A) will be less than 250 V 
B) will always be 250 V 
C) may be greater or less than 250 V 
D) none of the above 
A) will be less than 250 V 
B) will always be 250 V 
C) may be greater or less than 250 V 
D) none of the above

Question 5

Two D.C. shunt generators, each with armature resistance of 0.02 ohm and field resistance of 50 ohm run in parallel and supply a total current of 1000 amperes to the load circuit. If their e.m.fs. are 270 V and 265 V, their bus bar voltage will be

Accepted Answer

A) 270 V 
B) 267.5V 
C) 265 V 
D) 257.4V 
A) 270 V 
B) 267.5V 
C) 265 V 
D) 257.4V

Question 6

The number of armature parallel paths in a two-pole D.C. generator having duplexlap winding is

Accepted Answer

A) 2 
B) 4 
C) 6 
D) 8 
A) 2 
B) 4 
C) 6 
D) 8

Question 7

In a D.C. generator the critical resistance can be increased by

Accepted Answer

A) increasing its field resistance 
B) decreasing its field resistance 
C) increasing its speed 
D) decreasing its speed 
A) increasing its field resistance 
B) decreasing its field resistance 
C) increasing its speed 
D) decreasing its speed

Question 8

The series field of a short-shunt D.C. generator is excited by

Accepted Answer

A) external current 
B) armature current 
C) shunt current 
D) load current 
A) external current 
B) armature current 
C) shunt current 
D) load current

Question 9

The terminal voltage of a series generator is 150 V when the load current is 5 A. If the load current is increased to 10 A, the terminal voltage will be

Accepted Answer

A) 150 V 
B) less than 150 V 
C) greater than 150 V 
D) none of the above 
A) 150 V 
B) less than 150 V 
C) greater than 150 V 
D) none of the above

Question 10

A D.C. generator works on the principle of

Accepted Answer

A) Lenz's law 
B) Ohm's law 
C) Faraday's law of electromagnetic induction 
D) none of the above 
A) Lenz's law 
B) Ohm's law 
C) Faraday's law of electromagnetic induction 
D) none of the above

Question 11

A shunt generator can self-excite

Accepted Answer

A) only if the resistance of the field circuit is less than critical value 
B) only if the resistance of the field circuit is greater than critical value 
C) irrespective of the value of the resis-tance in the field circuit 
D) none 
A) only if the resistance of the field circuit is less than critical value 
B) only if the resistance of the field circuit is greater than critical value 
C) irrespective of the value of the resis-tance in the field circuit 
D) none

Question 12

As a result of armature reaction, the reduction in the total mutual air gap flux in aD.C. generator is approximately

Accepted Answer

A) 40 percent 
B) 25 percent 
C) 10 percent 
D) 5 percent 
A) 40 percent 
B) 25 percent 
C) 10 percent 
D) 5 percent

Question 13

A series generator can self-excite

Accepted Answer

A) only if the load current is zero 
B) only if the load current is not zero 
C) irrespective of the value of load current 
D) none of the above 
A) only if the load current is zero 
B) only if the load current is not zero 
C) irrespective of the value of load current 
D) none of the above

Question 14

Two generators are running in parallel. One of the generators may run as motor for which of the following reasons ?

Accepted Answer

A) The direction of that generator is reversed 
B) The speed of that generator is increased 
C) The field of that generator is weakened 
D) That generator takes large share of loads 
A) The direction of that generator is reversed 
B) The speed of that generator is increased 
C) The field of that generator is weakened 
D) That generator takes large share of loads

Question 15

The main factor which leads to unstable parallel operation of flat and over compounded generators is

Accepted Answer

A) their rising voltage characteristics 
B) unequal number of turns in their series field windings 
C) unequal speed regulation of their primemovers 
D) unequal series field resistances 
A) their rising voltage characteristics 
B) unequal number of turns in their series field windings 
C) unequal speed regulation of their primemovers 
D) unequal series field resistances

Question 16

For both lap and wave windings, there are as many commutator bars as the numberof

Accepted Answer

A) slots 
B) armature conductors 
C) winding elements 
D) poles 
A) slots 
B) armature conductors 
C) winding elements 
D) poles

Question 17

When two D.C. generators are running in parallel an equilizer bar is used

Accepted Answer

A) to increase the series flux 
B) to increase the generated e.m.f. 
C) to reduce the combined effect of ar-mature reaction of both the machines 
D) so that the two identical machines will pass approximately equal currents to the load 
A) to increase the series flux 
B) to increase the generated e.m.f. 
C) to reduce the combined effect of ar-mature reaction of both the machines 
D) so that the two identical machines will pass approximately equal currents to the load

Question 18

With a D.C. generator which of the following regulation is preferred ?

Accepted Answer

A) 100% regulation 
B) infinite regulation 
C) 50% regulation 
D) 1% regulation 
A) 100% regulation 
B) infinite regulation 
C) 50% regulation 
D) 1% regulation

Which generator would you prefer for feeding long D.C. transmission lines ?

Shunt generators are most suited for stable parallel operation because of their

The essential condition for parallel operation of two D.C. generators is that they have '

The open circuit voltage of a compound generator is 250 V. At full load the terminal voltage

Two D.C. shunt generators, each with armature resistance of 0.02 ohm and field resistance of 50 ohm run in parallel and supply a total current of 1000 amperes to the load circuit. If their e.m.fs. are 270 V and 265 V, their bus bar voltage will be

The number of armature parallel paths in a two-pole D.C. generator having duplexlap winding is

In a D.C. generator the critical resistance can be increased by

The series field of a short-shunt D.C. generator is excited by

The terminal voltage of a series generator is 150 V when the load current is 5 A. If the load current is increased to 10 A, the terminal voltage will be

A D.C. generator works on the principle of

A shunt generator can self-excite

As a result of armature reaction, the reduction in the total mutual air gap flux in aD.C. generator is approximately

A series generator can self-excite

Two generators are running in parallel. One of the generators may run as motor for which of the following reasons ?

The main factor which leads to unstable parallel operation of flat and over compounded generators is

For both lap and wave windings, there are as many commutator bars as the numberof

When two D.C. generators are running in parallel an equilizer bar is used

With a D.C. generator which of the following regulation is preferred ?

Transformer Fundamentals and Operation

Transformer Technology and Design

Transformer: Resistance, Oil, Relays, Harmonics, and Core Properties

Transformers: Efficiency, Design, and Testing

Transformers: Voltage Regulation, Efficiency, and Protection

Transformer and D.C Motor

D.C Motors and Starters

D.C Motors and Speed Control

D.C Motors and Controls

D.C Motors and Generators

D.C Machine and Generator Laminations, Commutation, and Components

D.C Generators and Commutators

D.C Generator Operation and Construction

D.C Generators

Filters

Exam 15: Direct Current Generators and Parallel Operation

Which generator would you prefer for feeding long D.C. transmission lines ?

Shunt generators are most suited for stable parallel operation because of their

The essential condition for parallel operation of two D.C. generators is that they have '

The open circuit voltage of a compound generator is 250 V. At full load the terminal voltage

Two D.C. shunt generators, each with armature resistance of 0.02 ohm and field resistance of 50 ohm run in parallel and supply a total current of 1000 amperes to the load circuit. If their e.m.fs. are 270 V and 265 V, their bus bar voltage will be

The number of armature parallel paths in a two-pole D.C. generator having duplexlap winding is

In a D.C. generator the critical resistance can be increased by

The series field of a short-shunt D.C. generator is excited by

The terminal voltage of a series generator is 150 V when the load current is 5 A. If the load current is increased to 10 A, the terminal voltage will be

A D.C. generator works on the principle of

A shunt generator can self-excite

As a result of armature reaction, the reduction in the total mutual air gap flux in aD.C. generator is approximately

A series generator can self-excite

Two generators are running in parallel. One of the generators may run as motor for which of the following reasons ?

The main factor which leads to unstable parallel operation of flat and over compounded generators is

For both lap and wave windings, there are as many commutator bars as the numberof

When two D.C. generators are running in parallel an equilizer bar is used

With a D.C. generator which of the following regulation is preferred ?

Transformer Fundamentals and Operation

Transformer Technology and Design

Transformer: Resistance, Oil, Relays, Harmonics, and Core Properties

Transformers: Efficiency, Design, and Testing

Transformers: Voltage Regulation, Efficiency, and Protection

Transformer and D.C Motor

D.C Motors and Starters

D.C Motors and Speed Control

D.C Motors and Controls

D.C Motors and Generators

D.C Machine and Generator Laminations, Commutation, and Components

D.C Generators and Commutators

D.C Generator Operation and Construction

D.C Generators

Filters