Question 1

The notation (2300V 3$\theta$ 60 Hz) means that the motor is ____-phase.

Accepted Answer

A)  one 
B)  three 
C)  60 
D)  2300 
A)  one 
B)  three 
C)  60 
D)  2300 B

Question 2

Current transformers produce an output current of 5 amperes under a(n) ____________________ condition.

Accepted Answer

short circuit

Question 3

A(n) ____________________ box indicates terminal numbers for the relay and these numbers should not be confused with wire numbers.

Accepted Answer

square

Question 4

A ____ switch permits power to be supplied to the circuit or not.

Accepted Answer

A)  stop-run 
B)  float 
C)  pressure 
D)  flow 
A)  stop-run 
B)  float 
C)  pressure 
D)  flow

Question 5

In the schematic, the connections made inside the MCC are shown with ____ lines.

Accepted Answer

A)  dashed 
B)  solid 
C)  wavy 
D)  slashed 
A)  dashed 
B)  solid 
C)  wavy 
D)  slashed

Question 6

What is the meaning of the notation (200A 5000V DISCONNECT SWITCH)?

Accepted Answer

This notation indicates that t

Question 7

Terminal strips are used as connection points between the control wiring inside the cabinet and inputs or outputs to the machine or control panel.

Accepted Answer

A) True 
 B)False

Question 8

What is the advantage of connecting components to a terminal strip?

Accepted Answer

Although connecting components to a term

Question 9

What letter indicates a connection between terminals?

Accepted Answer

A)  A 
B)  F 
C)  O 
D)  X 
A)  A 
B)  F 
C)  O 
D)  X

Question 10

What is the primary difference between the point-to-point and terminal strip methods?

Accepted Answer

The primary difference between

Question 11

____________________ diagrams can be misleading in that they show all components grouped together.

Accepted Answer

The answer of ____________________ diagrams can be misleading in that...

Question 12

Some control components, such as limit switches, photodetectors, or flow switches, may be located on the machine itself, while other components such as control relays and motor starters may be located inside a cabinet.

Accepted Answer

A) True 
 B)False

Question 13

Why is practice important for reading schematic diagrams?

Accepted Answer

The old saying "Practice makes perfect"

The notation (2300V 3 $\theta$ 60 Hz) means that the motor is ____-phase.

Current transformers produce an output current of 5 amperes under a(n) ____________________ condition.

A(n) ____________________ box indicates terminal numbers for the relay and these numbers should not be confused with wire numbers.

A ____ switch permits power to be supplied to the circuit or not.

In the schematic, the connections made inside the MCC are shown with ____ lines.

What is the meaning of the notation (200A 5000V DISCONNECT SWITCH)?

Terminal strips are used as connection points between the control wiring inside the cabinet and inputs or outputs to the machine or control panel.

What is the advantage of connecting components to a terminal strip?

What letter indicates a connection between terminals?

What is the primary difference between the point-to-point and terminal strip methods?

____________________ diagrams can be misleading in that they show all components grouped together.

Some control components, such as limit switches, photodetectors, or flow switches, may be located on the machine itself, while other components such as control relays and motor starters may be located inside a cabinet.

Why is practice important for reading schematic diagrams?

General Principles of Motor Control, Symbols and Schematic Diagrams

Manual Starters and Overload Relays

The Control Transformer, Relays, Contactors, and Motor Starters

Timing Relays, Pressure Switches and Sensors

Float Switches, Flow Switches and Sensors

Limit Switches and Phase Failure Relays

Temperature Sensing, Devices M Solenoid and Motor Operated Valves

Hall Effect Sensors and Proximity Detectors

Basic Control Circuits and Photodetectors

Schematics, Wiring Diagrams Circuit (1), Timed Starting for Three Motors Circuit (2)

Float Switch Control of a Pump and Pilot Lights Circuit (3), Developing a Wiring Diagram Circuit (1)

Developing a Wiring Diagram Circuit (2) and Developing a Wiring Diagram Circuit (3)

Multiple Push Button Stations and Hand-Off-Automatic Controls

Forward-Reverse Control, Jogging and Inching

Dc Motors and Sequence Control

Solid-State Dc Drives and Starting Methods for DC Motors

Stepping Motors, the Motor and Starting Methods

Autotransformer Starting , Resistor and Reactor Starting for Ac Motors

Wye-Delta Starting, Part Winding Starters

Braking , Consequent Pole Motors, Variable Voltage and Magnetic Clutches

Variable Frequency Control

Troubleshooting, Motor Installation and Developing Control Circuits

Digital Logic and the Bounceless Switch

Programmable Logic Controllers and Start-Stop Push Button Control

Programming a PLC and Analog Sensing for Programmable Controllers

Filters

Exam 13: Installing Control Systems and Reading Large Schematic Diagrams

The notation (2300V 3 θ\thetaθ 60 Hz) means that the motor is ____-phase.

Current transformers produce an output current of 5 amperes under a(n) ____________________ condition.

A(n) ____________________ box indicates terminal numbers for the relay and these numbers should not be confused with wire numbers.

A ____ switch permits power to be supplied to the circuit or not.

In the schematic, the connections made inside the MCC are shown with ____ lines.

What is the meaning of the notation (200A 5000V DISCONNECT SWITCH)?

Terminal strips are used as connection points between the control wiring inside the cabinet and inputs or outputs to the machine or control panel.

What is the advantage of connecting components to a terminal strip?

What letter indicates a connection between terminals?

What is the primary difference between the point-to-point and terminal strip methods?

____________________ diagrams can be misleading in that they show all components grouped together.

Some control components, such as limit switches, photodetectors, or flow switches, may be located on the machine itself, while other components such as control relays and motor starters may be located inside a cabinet.

Why is practice important for reading schematic diagrams?

General Principles of Motor Control, Symbols and Schematic Diagrams

Manual Starters and Overload Relays

The Control Transformer, Relays, Contactors, and Motor Starters

Timing Relays, Pressure Switches and Sensors

Float Switches, Flow Switches and Sensors

Limit Switches and Phase Failure Relays

Temperature Sensing, Devices M Solenoid and Motor Operated Valves

Hall Effect Sensors and Proximity Detectors

Basic Control Circuits and Photodetectors

Schematics, Wiring Diagrams Circuit (1), Timed Starting for Three Motors Circuit (2)

Float Switch Control of a Pump and Pilot Lights Circuit (3), Developing a Wiring Diagram Circuit (1)

Developing a Wiring Diagram Circuit (2) and Developing a Wiring Diagram Circuit (3)

Multiple Push Button Stations and Hand-Off-Automatic Controls

Forward-Reverse Control, Jogging and Inching

Dc Motors and Sequence Control

Solid-State Dc Drives and Starting Methods for DC Motors

Stepping Motors, the Motor and Starting Methods

Autotransformer Starting , Resistor and Reactor Starting for Ac Motors

Wye-Delta Starting, Part Winding Starters

Braking , Consequent Pole Motors, Variable Voltage and Magnetic Clutches

Variable Frequency Control

Troubleshooting, Motor Installation and Developing Control Circuits

Digital Logic and the Bounceless Switch

Programmable Logic Controllers and Start-Stop Push Button Control

Programming a PLC and Analog Sensing for Programmable Controllers

Filters

The notation (2300V 3 $\theta$ 60 Hz) means that the motor is ____-phase.