Question 1

Determine the plotted point for a PTPCC, where the specification for a part number is 5.23 ± 0.03 and an inspected measured value is 5.24.

Accepted Answer

0.33 or 33%

Question 2

What type of process is the packaging of tooth paste?

Accepted Answer

A)  continuance 
B)  batch 
C)  discrete 
D)  none of the above 
A)  continuance 
B)  batch 
C)  discrete 
D)  none of the above A

Question 3

Which of the following type(s) of short-run control is/are based on specifications?

Accepted Answer

A)  Z and W 
B)  precontrol 
C)  deviation chart 
D)  a and b 
A)  Z and W 
B)  precontrol 
C)  deviation chart 
D)  a and b B

Question 4

What type of process is the production of soup?

Accepted Answer

A)  continuance 
B)  batch 
C)  discrete 
D)  none of the above 
A)  continuance 
B)  batch 
C)  discrete 
D)  none of the above

Question 5

Determine the central lines for Z and MW charts and draw the charts. If the target X is 2.00 and the target R is 0.05, determine the plotted points for the following values. $$\begin{array} { c c } 
\text { Subgroup } & \text { Observed Value } \
1 & 2.05 \
2 & 2.08 \
3 & 1.97
\end{array}$$
$\begin{array} { |l|l|l|l|l|l|l| l| }
\hline \quad&\quad&\quad&\quad&\quad&\quad&\quad&\quad\
\hline \quad&\quad&\quad&\quad&\quad&\quad&\quad&\quad\
\hline \quad&\quad&\quad&\quad&\quad&\quad&\quad&\quad\
\hline \quad&\quad&\quad&\quad&\quad&\quad&\quad&\quad\
\hline \quad&\quad&\quad&\quad&\quad&\quad&\quad&\quad\
\hline \quad&\quad&\quad&\quad&\quad&\quad&\quad&\quad\
\hline \quad&\quad&\quad&\quad&\quad&\quad&\quad&\quad\
\hline \quad&\quad&\quad&\quad&\quad&\quad&\quad&\quad\
\hline \quad&\quad&\quad&\quad&\quad&\quad&\quad&\quad\
\hline 
\end{array}$

Accepted Answer

Z's = 1.0,

Question 6

Which of the following type(s ) of short-run control is/are derived from the X and R charts?

Accepted Answer

A)  Z and W charts 
B)  precontrol 
C)  specification chart 
D)  b and c 
A)  Z and W charts 
B)  precontrol 
C)  specification chart 
D)  b and c

Question 7

Before changing from the set up mode to the run mode in precontrol there must be

Accepted Answer

A)  3 consecutive goods in the green zone 
B)  5 consecutive goods in the green zone 
C)  7 consecutive goods in the green zone 
D)  acceptable parts 
A)  3 consecutive goods in the green zone 
B)  5 consecutive goods in the green zone 
C)  7 consecutive goods in the green zone 
D)  acceptable parts

Determine the plotted point for a PTPCC, where the specification for a part number is 5.23 ± 0.03 and an inspected measured value is 5.24.

What type of process is the packaging of tooth paste?

Which of the following type(s) of short-run control is/are based on specifications?

What type of process is the production of soup?

Determine the central lines for Z and MW charts and draw the charts. If the target X is 2.00 and the target R is 0.05, determine the plotted points for the following values. Subgroup Observed Value 1 2.05 2 2.08 3 1.97

Which of the following type(s ) of short-run control is/are derived from the X and R charts?

Before changing from the set up mode to the run mode in precontrol there must be

Introduction to Quality Improvement

Lean Enterprise

Six Sigma

Statistical Process Control

Fundamentals of Statistics

Control Charts for Variables

Fundamentals of Probability

Control Charts for Attributes

Acceptance Sampling

Reliability

Management and Planning Tools

Experimental Design

Filters

Exam 7: Additional Spc Techniques for Variables

Determine the plotted point for a PTPCC, where the specification for a part number is 5.23 ± 0.03 and an inspected measured value is 5.24.

What type of process is the packaging of tooth paste?

Which of the following type(s) of short-run control is/are based on specifications?

What type of process is the production of soup?

Determine the central lines for Z and MW charts and draw the charts. If the target X is 2.00 and the target R is 0.05, determine the plotted points for the following values. Subgroup Observed Value 1 2.05 2 2.08 3 1.97

Which of the following type(s ) of short-run control is/are derived from the X and R charts?

Before changing from the set up mode to the run mode in precontrol there must be

Introduction to Quality Improvement

Lean Enterprise

Six Sigma

Statistical Process Control

Fundamentals of Statistics

Control Charts for Variables

Fundamentals of Probability

Control Charts for Attributes

Acceptance Sampling

Reliability

Management and Planning Tools

Experimental Design

Filters