Question 1

The ____ command is used to start a line of logic.

Accepted Answer

A)  STR 
B)  SHF 
C)  AND 
D)  ENT 
A)  STR 
B)  SHF 
C)  AND 
D)  ENT A

Question 2

The ENT command causes an instruction to be entered into the logic of the CPU.

Accepted Answer

A) True 
 B)False  True

Question 3

Discuss the use of shielded cable in signal wiring and the noise reduction it provides.

Accepted Answer

Shielded cable is used for the installation of signal wiring. One of the most common types uses twisted wires with a Mylar foil shield. The ground wire must be grounded if the shielding is to operate properly. This type of shielded cable can provide a noise reduction ratio of about 30,000: 1. Another type of signal cable uses a twisted pair of signal wires surrounded by a braided shield. This type of cable provides a noise reduction of about 300: 1.

Question 4

Try to keep wire runs ____.

Accepted Answer

A)  as long as possible 
B)  high in surface area 
C)  near electrical noise 
D)  as short as possible 
A)  as long as possible 
B)  high in surface area 
C)  near electrical noise 
D)  as short as possible

Question 5

What rules must be followed with almost all programmable logic controllers?

Accepted Answer

The following are the rules that must be

Question 6

____________________ is a number system that contains only eight digits, 0 through 7.

Accepted Answer

The answer of ____________________ is a number system that contains...

Question 7

____ is generally thought of as being electrically neutral, or zero at all points.

Accepted Answer

A)  Ground 
B)  Noise 
C)  Shield 
D)  Signal 
A)  Ground 
B)  Noise 
C)  Shield 
D)  Signal

Question 8

When using a small programming terminal, the program must be entered in a language called ____.

Accepted Answer

A)  Contact 1 
B)  Boolean 
C)  Ada 
D)  C++ 
A)  Contact 1 
B)  Boolean 
C)  Ada 
D)  C++

Question 9

What is one common method used to construct an analog pressure sensor?

Accepted Answer

One of the most common methods is to let

Question 10

How can CPUs differentiate between coils and contacts with respect to the timer command?

Accepted Answer

The CPU can interpret a timer

The ____ command is used to start a line of logic.

The ENT command causes an instruction to be entered into the logic of the CPU.

Discuss the use of shielded cable in signal wiring and the noise reduction it provides.

Try to keep wire runs ____.

What rules must be followed with almost all programmable logic controllers?

____________________ is a number system that contains only eight digits, 0 through 7.

____ is generally thought of as being electrically neutral, or zero at all points.

When using a small programming terminal, the program must be entered in a language called ____.

What is one common method used to construct an analog pressure sensor?

How can CPUs differentiate between coils and contacts with respect to the timer command?

General Principles of Motor Control, Symbols and Schematic Diagrams

Manual Starters and Overload Relays

The Control Transformer, Relays, Contactors, and Motor Starters

Timing Relays, Pressure Switches and Sensors

Float Switches, Flow Switches and Sensors

Limit Switches and Phase Failure Relays

Temperature Sensing, Devices M Solenoid and Motor Operated Valves

Hall Effect Sensors and Proximity Detectors

Basic Control Circuits and Photodetectors

Schematics, Wiring Diagrams Circuit (1), Timed Starting for Three Motors Circuit (2)

Float Switch Control of a Pump and Pilot Lights Circuit (3), Developing a Wiring Diagram Circuit (1)

Developing a Wiring Diagram Circuit (2) and Developing a Wiring Diagram Circuit (3)

Installing Control Systems and Reading Large Schematic Diagrams

Multiple Push Button Stations and Hand-Off-Automatic Controls

Forward-Reverse Control, Jogging and Inching

Dc Motors and Sequence Control

Solid-State Dc Drives and Starting Methods for DC Motors

Stepping Motors, the Motor and Starting Methods

Autotransformer Starting , Resistor and Reactor Starting for Ac Motors

Wye-Delta Starting, Part Winding Starters

Braking , Consequent Pole Motors, Variable Voltage and Magnetic Clutches

Variable Frequency Control

Troubleshooting, Motor Installation and Developing Control Circuits

Digital Logic and the Bounceless Switch

Programmable Logic Controllers and Start-Stop Push Button Control

Filters

Exam 26: Programming a PLC and Analog Sensing for Programmable Controllers

The ____ command is used to start a line of logic.

The ENT command causes an instruction to be entered into the logic of the CPU.

Discuss the use of shielded cable in signal wiring and the noise reduction it provides.

Try to keep wire runs ____.

What rules must be followed with almost all programmable logic controllers?

____________________ is a number system that contains only eight digits, 0 through 7.

____ is generally thought of as being electrically neutral, or zero at all points.

When using a small programming terminal, the program must be entered in a language called ____.

What is one common method used to construct an analog pressure sensor?

How can CPUs differentiate between coils and contacts with respect to the timer command?

General Principles of Motor Control, Symbols and Schematic Diagrams

Manual Starters and Overload Relays

The Control Transformer, Relays, Contactors, and Motor Starters

Timing Relays, Pressure Switches and Sensors

Float Switches, Flow Switches and Sensors

Limit Switches and Phase Failure Relays

Temperature Sensing, Devices M Solenoid and Motor Operated Valves

Hall Effect Sensors and Proximity Detectors

Basic Control Circuits and Photodetectors

Schematics, Wiring Diagrams Circuit (1), Timed Starting for Three Motors Circuit (2)

Float Switch Control of a Pump and Pilot Lights Circuit (3), Developing a Wiring Diagram Circuit (1)

Developing a Wiring Diagram Circuit (2) and Developing a Wiring Diagram Circuit (3)

Installing Control Systems and Reading Large Schematic Diagrams

Multiple Push Button Stations and Hand-Off-Automatic Controls

Forward-Reverse Control, Jogging and Inching

Dc Motors and Sequence Control

Solid-State Dc Drives and Starting Methods for DC Motors

Stepping Motors, the Motor and Starting Methods

Autotransformer Starting , Resistor and Reactor Starting for Ac Motors

Wye-Delta Starting, Part Winding Starters

Braking , Consequent Pole Motors, Variable Voltage and Magnetic Clutches

Variable Frequency Control

Troubleshooting, Motor Installation and Developing Control Circuits

Digital Logic and the Bounceless Switch

Programmable Logic Controllers and Start-Stop Push Button Control

Filters