Question 1

The gears in the final drive assembly that allow the left and right drive wheels to turn at different speeds are called:

Accepted Answer

A)  torque multiplication gears. 
B)  torque transmission gears. 
C)  torque distribution gears. 
D)  differential gears. 
A)  torque multiplication gears. 
B)  torque transmission gears. 
C)  torque distribution gears. 
D)  differential gears.

Question 2

Feeler gauges are usually made of brass.

Accepted Answer

A) True 
 B)False

Question 3

The _______ punch makes a bigger indentation that centers a drill bit at the point where a hole is required to be drilled.

Accepted Answer

A)  Center 
B)  Prick 
C)  Drift 
D)  Pin 
A)  Center 
B)  Prick 
C)  Drift 
D)  Pin

Question 4

Tech A says that a dead blow hammer reduces rebound of the hammer. Tech B says that a dead blow hammer should be used with a chisel to cut the head of a bolt off. Who is correct?
​

Accepted Answer

A)  Tech A 
B)  Tech B 
C)  Both A and B 
D)  Neither A nor B 
A)  Tech A 
B)  Tech B 
C)  Both A and B 
D)  Neither A nor B

Question 5

Dial indicators can typically measure with an accuracy of:

Accepted Answer

A)  0.100" 
B)  0.001" 
C)  0.010" 
D)  1.000" 
A)  0.100" 
B)  0.001" 
C)  0.010" 
D)  1.000"

Question 6

The final drive unit is used to provide gear reduction and also to:

Accepted Answer

A)  change the direction of the power delivered to the drive wheels. 
B)  allow the left and right wheels to travel at different speeds around a curve. 
C)  Both A and B 
D)  None of the above 
A)  change the direction of the power delivered to the drive wheels. 
B)  allow the left and right wheels to travel at different speeds around a curve. 
C)  Both A and B 
D)  None of the above

Question 7

_______ are convenient for occasional riveting of light materials.

Accepted Answer

A)  Blind rivets 
B)  Finished rivets 
C)  Pop rivet guns 
D)  All of the above 
A)  Blind rivets 
B)  Finished rivets 
C)  Pop rivet guns 
D)  All of the above

Question 8

The depth of blind holes in housings can best be measured using a:

Accepted Answer

A)  measuring tape. 
B)  steel rule. 
C)  dial bore gauge. 
D)  vernier caliper. 
A)  measuring tape. 
B)  steel rule. 
C)  dial bore gauge. 
D)  vernier caliper.

Question 9

Power tools can be powered by _______, such as in a nail gun, or by a gasoline engine, such as in a portable compressor.

Accepted Answer

A)  Battery 
B)  Power cord 
C)  Airflow 
D)  Burning of propellant 
A)  Battery 
B)  Power cord 
C)  Airflow 
D)  Burning of propellant

Question 10

Technician A states that one shouldn't use tools that are potentially unsafe. Technician B states that one shouldn't use tools they have not been trained on. Who is correct?

Accepted Answer

A)  Technician A 
B)  Technician B 
C)  Both A and B 
D)  Neither A nor B 
A)  Technician A 
B)  Technician B 
C)  Both A and B 
D)  Neither A nor B

Question 11

Technician A says that when using a file; apply pressure to file in the direction of the cut and no pressure when pulling the file back. Technician B says that file cards are used to file uneven surfaces. Who is correct?

Accepted Answer

A)  Technician A 
B)  Technician B 
C)  Both A and B 
D)  Neither A nor B 
A)  Technician A 
B)  Technician B 
C)  Both A and B 
D)  Neither A nor B

Question 12

Precision measuring tools, such as a micrometer, can accurately measure down to ______ of an inch.

Accepted Answer

A)  1/100 
B)  1/1,000 
C)  1/10,000 
D)  1/100,000 
A)  1/100 
B)  1/1,000 
C)  1/10,000 
D)  1/100,000

Question 13

The ______ design of pry bar works well for applying force to tension belts or for moving parts into alignment.

Accepted Answer

A)  Double tapered end 
B)  Plastic handle/tapered end 
C)  Either A or B 
D)  Neither A nor B 
A)  Double tapered end 
B)  Plastic handle/tapered end 
C)  Either A or B 
D)  Neither A nor B

Question 14

Vernier micrometers, equipped with the addition of a vernier scale, can measure down to _________ of an inch.

Accepted Answer

A)  1/100 
B)  1/1,000 
C)  1/10,000 
D)  1/100,000 
A)  1/100 
B)  1/1,000 
C)  1/10,000 
D)  1/100,000

Question 15

When drilling a hole to insert a screw extractor, it is important to carefully drill the hole in the center of the bolt or stud in case you end up having to drill the bolt out.

Accepted Answer

A) True 
 B)False

Question 16

All of the following are variations on the open-end wrench, EXCEPT:

Accepted Answer

A)  flare nut wrench. 
B)  flare tubing wrench. 
C)  box-end wrench. 
D)  None of the answers listed 
A)  flare nut wrench. 
B)  flare tubing wrench. 
C)  box-end wrench. 
D)  None of the answers listed

Question 17

Technician A states that micrometers are used to measure long distances. Technician B states that micrometers should always be stored with a gap between the spindle and anvil so metal expansion does not interfere with their calibration. Who is correct?

Accepted Answer

A)  Technician A 
B)  Technician B 
C)  Both A and B 
D)  Neither A nor B 
A)  Technician A 
B)  Technician B 
C)  Both A and B 
D)  Neither A nor B

Question 18

A screw or bolt with a cross-shaped recess requires a(n) ___________ screwdriver or a Pozidriv screwdriver.

Accepted Answer

A)  Phillips-head 
B)  offset 
C)  ratcheting 
D)  impact 
A)  Phillips-head 
B)  offset 
C)  ratcheting 
D)  impact

Question 19

Technician A says that the countershaft is splined to fit into the hub in the clutch disc. Technician B says that the output shaft has gears that are meshed with the countershaft gears. Who is correct?

Accepted Answer

A)  Technician A 
B)  Technician B 
C)  Both A and B 
D)  Neither A nor B 
A)  Technician A 
B)  Technician B 
C)  Both A and B 
D)  Neither A nor B

Question 20

A dial bore gauge determines if the diameter is ______ according to the manufacturer's specifications.

Accepted Answer

A)  Worn 
B)  Tapered 
C)  Out-of-round 
D)  All of the above 
A)  Worn 
B)  Tapered 
C)  Out-of-round 
D)  All of the above

Exam 3: Basic Tools and Precision Measuring

The gears in the final drive assembly that allow the left and right drive wheels to turn at different speeds are called:

Feeler gauges are usually made of brass.

The _______ punch makes a bigger indentation that centers a drill bit at the point where a hole is required to be drilled.

Tech A says that a dead blow hammer reduces rebound of the hammer. Tech B says that a dead blow hammer should be used with a chisel to cut the head of a bolt off. Who is correct? ​

Dial indicators can typically measure with an accuracy of:

The final drive unit is used to provide gear reduction and also to:

_______ are convenient for occasional riveting of light materials.

The depth of blind holes in housings can best be measured using a:

Power tools can be powered by _______, such as in a nail gun, or by a gasoline engine, such as in a portable compressor.

Technician A states that one shouldn't use tools that are potentially unsafe. Technician B states that one shouldn't use tools they have not been trained on. Who is correct?

Technician A says that when using a file; apply pressure to file in the direction of the cut and no pressure when pulling the file back. Technician B says that file cards are used to file uneven surfaces. Who is correct?

Precision measuring tools, such as a micrometer, can accurately measure down to ______ of an inch.

The ______ design of pry bar works well for applying force to tension belts or for moving parts into alignment.

Vernier micrometers, equipped with the addition of a vernier scale, can measure down to _________ of an inch.

When drilling a hole to insert a screw extractor, it is important to carefully drill the hole in the center of the bolt or stud in case you end up having to drill the bolt out.

All of the following are variations on the open-end wrench, EXCEPT:

Technician A states that micrometers are used to measure long distances. Technician B states that micrometers should always be stored with a gap between the spindle and anvil so metal expansion does not interfere with their calibration. Who is correct?

A screw or bolt with a cross-shaped recess requires a(n) ___________ screwdriver or a Pozidriv screwdriver.

Technician A says that the countershaft is splined to fit into the hub in the clutch disc. Technician B says that the output shaft has gears that are meshed with the countershaft gears. Who is correct?

A dial bore gauge determines if the diameter is ______ according to the manufacturer's specifications.

Strategy-Based Diagnostics

Safety

Fasteners and Thread Repair

Vehicle, Customer, and Service Information

Automatic Transmission Fundamentals

Transmission Components

Hydraulic Fundamentals

Torque Converter Principles

Hydraulically Controlled Transmission

Electronically Controlled Transmission

In-Vehicle Transmission Repairs

Transmission Removal

Transmission Disassembly

Hydraulic System Rebuilding

Gear Train Rebuilding

Valve Body and Electric Service

Transmission Reassembly

Transmission Reinstallation

Dual Clutch Transmissions

Continuously Variable Transmissions

Hybrid Transmissions

Honda Transmissions

Chrysler 6 Speed 62te Transmission

6t40 6f35 Transmission

Zf 9hp Chrysler 948te Transmission

Ford 6r60 Zf6hp26

Allison 1000 and 2000 Series Transmissions

Filters

Tech A says that a dead blow hammer reduces rebound of the hammer. Tech B says that a dead blow hammer should be used with a chisel to cut the head of a bolt off. Who is correct?