Question 1

The direction of sight of a cutting plane line shows what part of the feature is viewed when the rest of it is taken away.

Accepted Answer

A) True 
 B)False  True

Question 2

Describe the practice of conventional revolution and explain why true projection is a poor practice when this application is used.

Accepted Answer

When the true projection of a feature results in foreshortening, the feature should be revolved onto a plane perpendicular to the line of sight as in Figure 13.22. The revolved spoke shown gives a clear representation. The true projection is poor practice because the spoke is foreshortened.

Question 3

Staggered interior features of an object are sectioned by the cutting plane line to align through the feature.

Accepted Answer

A) True 
 B)False  False

Question 4

A cutting plane line is shown completely through the object, passing through offset features of the object. The section on the drawing is a(n) ____.

Accepted Answer

A)  full section 
B)  half section 
C)  aligned section 
D)  removed section 
E)  none of the above 
A)  full section 
B)  half section 
C)  aligned section 
D)  removed section 
E)  none of the above

Question 5

True projection is always important between views on a print.

Accepted Answer

A) True 
 B)False

Question 6

Section lines are shown on all parts of a section, especially thin parts.

Accepted Answer

A) True 
 B)False

Question 7

A full section is drawn when the cutting plane extends completely through the object, usually along a center plane.

Accepted Answer

A) True 
 B)False

Question 8

A gasket is commonly sectioned even though it is a thin part.

Accepted Answer

A) True 
 B)False

Question 9

When using the option of a revolved section, ____.

Accepted Answer

A)  the piece rotated must be completely broken away from the rest of the object 
B)  the piece rotated should have section lines 
C)  the piece rotated should not have dimensions describing it 
D)  the piece rotated should be in a space close by and labeled with the appropriate cutting plane label 
E)  none of the above 
A)  the piece rotated must be completely broken away from the rest of the object 
B)  the piece rotated should have section lines 
C)  the piece rotated should not have dimensions describing it 
D)  the piece rotated should be in a space close by and labeled with the appropriate cutting plane label 
E)  none of the above

Question 10

A sectional view established by revolving 90 degrees, in place, into a plane perpendicular to the line of sight, generally used to show the cross section of a part or feature that has consistent shape throughout the length.

Accepted Answer

A)  Removed section 
B)  Revolved section 
C)  Aligned section 
D)  Offset section 
E)  none of the above 
A)  Removed section 
B)  Revolved section 
C)  Aligned section 
D)  Offset section 
E)  none of the above

Question 11

A conventional revolution is used when the true projection of a feature results in foreshortening.

Accepted Answer

A) True 
 B)False

Question 12

What are coded section lines used for?

Accepted Answer

To represent specifi

Question 13

Used typically for symmetrical objects; the cutting-plane line actually cuts through one quarter of the part. The sectional view shows half of the interior and half of the exterior at the same time.

Accepted Answer

A)  Full section 
B)  Half section 
C)  Broken out section 
D)  Removed section 
E)  none of the above 
A)  Full section 
B)  Half section 
C)  Broken out section 
D)  Removed section 
E)  none of the above

Question 14

The sectional view is created by placing an imaginary _________________________ through the object cutting away the area to be exposed.

Accepted Answer

The answer of The sectional view is created by placing...

Question 15

If there are enough sectional views on a drawing to use up all of the letters of the alphabet, then _______ letters are used to label the cutting plane lines and related views, such as ___________.

Accepted Answer

double, AA

Question 16

Dimensioning to hidden features is a poor practice on a print.

Accepted Answer

A) True 
 B)False

Question 17

The cutting-plane line is a thick line representing the cutting plane. The cutting plane line can be shown using alternating long and two short dashes, or evenly spaced dashes.

Accepted Answer

A) True 
 B)False

Question 18

The change in direction of the cutting plane line is less than 90° in an aligned section.

Accepted Answer

A) True 
 B)False

Question 19

A removed section represents a portion of a part pivoted 90° and removed to show the section at that location.

Accepted Answer

A) True 
 B)False

Question 20

A revolved section is used when a feature that has a constant shape throughout the length is rotated so that the adjacent view shows the feature's constant shape.

Accepted Answer

A) True 
 B)False

The direction of sight of a cutting plane line shows what part of the feature is viewed when the rest of it is taken away.

Describe the practice of conventional revolution and explain why true projection is a poor practice when this application is used.

Staggered interior features of an object are sectioned by the cutting plane line to align through the feature.

A cutting plane line is shown completely through the object, passing through offset features of the object. The section on the drawing is a(n) ____.

True projection is always important between views on a print.

Section lines are shown on all parts of a section, especially thin parts.

A full section is drawn when the cutting plane extends completely through the object, usually along a center plane.

A gasket is commonly sectioned even though it is a thin part.

When using the option of a revolved section, ____.

A sectional view established by revolving 90 degrees, in place, into a plane perpendicular to the line of sight, generally used to show the cross section of a part or feature that has consistent shape throughout the length.

A conventional revolution is used when the true projection of a feature results in foreshortening.

What are coded section lines used for?

Used typically for symmetrical objects; the cutting-plane line actually cuts through one quarter of the part. The sectional view shows half of the interior and half of the exterior at the same time.

The sectional view is created by placing an imaginary _________________________ through the object cutting away the area to be exposed.

If there are enough sectional views on a drawing to use up all of the letters of the alphabet, then _ letters are used to label the cutting plane lines and related views, such as _____.

Dimensioning to hidden features is a poor practice on a print.

The cutting-plane line is a thick line representing the cutting plane. The cutting plane line can be shown using alternating long and two short dashes, or evenly spaced dashes.

The change in direction of the cutting plane line is less than 90° in an aligned section.

A removed section represents a portion of a part pivoted 90° and removed to show the section at that location.

A revolved section is used when a feature that has a constant shape throughout the length is rotated so that the adjacent view shows the feature's constant shape.

Introduction to Engineering and Manufacturing Technology Print Reading

Communicating with a Sketch

Scales and Precision Measurement

Reading Lines and Lettering on a Print

Reading Multiviews

Reading Auxiliary Views

Manufacturing Materials and Processes

Reading Dimensions

Reading Prints With Fasteners and Springs

Reading Geometric Dimensioning and Tolerancing

Reading Linkage, Cam, Gear, and Bearing Prints

Reading Precision Sheet Metal Prints

Reading Prints of Working Drawings

Welding Processes and Reading Welding Representations

Reading Prints of Pictorial Drawings

Reading Electrical Diagrams and Schematics

Filters

Exam 10: Reading Sections, Revolutions, and Conventional Breaks

The direction of sight of a cutting plane line shows what part of the feature is viewed when the rest of it is taken away.

Describe the practice of conventional revolution and explain why true projection is a poor practice when this application is used.

Staggered interior features of an object are sectioned by the cutting plane line to align through the feature.

A cutting plane line is shown completely through the object, passing through offset features of the object. The section on the drawing is a(n) ____.

True projection is always important between views on a print.

Section lines are shown on all parts of a section, especially thin parts.

A full section is drawn when the cutting plane extends completely through the object, usually along a center plane.

A gasket is commonly sectioned even though it is a thin part.

When using the option of a revolved section, ____.

A sectional view established by revolving 90 degrees, in place, into a plane perpendicular to the line of sight, generally used to show the cross section of a part or feature that has consistent shape throughout the length.

A conventional revolution is used when the true projection of a feature results in foreshortening.

What are coded section lines used for?

Used typically for symmetrical objects; the cutting-plane line actually cuts through one quarter of the part. The sectional view shows half of the interior and half of the exterior at the same time.

The sectional view is created by placing an imaginary _________________________ through the object cutting away the area to be exposed.

If there are enough sectional views on a drawing to use up all of the letters of the alphabet, then _______ letters are used to label the cutting plane lines and related views, such as ___________.

Dimensioning to hidden features is a poor practice on a print.

The cutting-plane line is a thick line representing the cutting plane. The cutting plane line can be shown using alternating long and two short dashes, or evenly spaced dashes.

The change in direction of the cutting plane line is less than 90° in an aligned section.

A removed section represents a portion of a part pivoted 90° and removed to show the section at that location.

A revolved section is used when a feature that has a constant shape throughout the length is rotated so that the adjacent view shows the feature's constant shape.

Introduction to Engineering and Manufacturing Technology Print Reading

Communicating with a Sketch

Scales and Precision Measurement

Reading Lines and Lettering on a Print

Reading Multiviews

Reading Auxiliary Views

Manufacturing Materials and Processes

Reading Dimensions

Reading Prints With Fasteners and Springs

Reading Geometric Dimensioning and Tolerancing

Reading Linkage, Cam, Gear, and Bearing Prints

Reading Precision Sheet Metal Prints

Reading Prints of Working Drawings

Welding Processes and Reading Welding Representations

Reading Prints of Pictorial Drawings

Reading Electrical Diagrams and Schematics

Filters

If there are enough sectional views on a drawing to use up all of the letters of the alphabet, then _ letters are used to label the cutting plane lines and related views, such as _____.