Question 1

Platform pattern, flat pack pattern, and terminal area shapes are all examples of ____.

Accepted Answer

A)  printed circuits 
B)  conductors 
C)  mounting pads 
D)  components of a grid system 
E)  none of the above 
A)  printed circuits 
B)  conductors 
C)  mounting pads 
D)  components of a grid system 
E)  none of the above C

Question 2

The placement of identification numbers of electronic components is variable.

Accepted Answer

A) True 
 B)False  False

Question 3

Cables are ____.

Accepted Answer

A)  used to connect components, equipment assemblies, or systems together 
B)  made up of insulated conductor wires, protective outer jacket, or some other means of holding the wires together, and connectors at one end or both ends 
C)  the part of the electrical transmission system where electricity is switched or transformed from a very high voltage to a conveniently usable form for distribution to homes or businesses 
D)  both a and b 
E)  all of the above 
A)  used to connect components, equipment assemblies, or systems together 
B)  made up of insulated conductor wires, protective outer jacket, or some other means of holding the wires together, and connectors at one end or both ends 
C)  the part of the electrical transmission system where electricity is switched or transformed from a very high voltage to a conveniently usable form for distribution to homes or businesses 
D)  both a and b 
E)  all of the above D

Question 4

MATCHING
Match the type of diagram with its description.
-Represents the electrical circuit as a three dimensional drawing

Accepted Answer

A) pictorial 
B) schematic 
C) block 
D) wiring 
E) schematic wiring
F)highway wiring
G)wireless
H)cable 
A) pictorial 
B) schematic 
C) block 
D) wiring 
E) schematic wiring
F)highway wiring
G)wireless
H)cable

Question 5

MATCHING
Match the type of diagram with its description.
-Shows the components but the interconnecting lines are omitted

Accepted Answer

A) pictorial 
B) schematic 
C) block 
D) wiring 
E) schematic wiring
F)highway wiring
G)wireless
H)cable 
A) pictorial 
B) schematic 
C) block 
D) wiring 
E) schematic wiring
F)highway wiring
G)wireless
H)cable

Question 6

The basic circuitry that makes any electronic device function is known as the ____.

Accepted Answer

A)  coupling circuitry 
B)  active circuitry 
C)  electronic circuitry 
D)  DC biasing 
E)  none of the above 
A)  coupling circuitry 
B)  active circuitry 
C)  electronic circuitry 
D)  DC biasing 
E)  none of the above

Question 7

____ have conductive material plated on the inside wall to form a conductive connection between layers of the circuit board.

Accepted Answer

A)  Terminal pads 
B)  Conductor traces 
C)  Master patterns 
D)  Plated through holes 
E)  none of the above 
A)  Terminal pads 
B)  Conductor traces 
C)  Master patterns 
D)  Plated through holes 
E)  none of the above

Question 8

An electrical system is the same thing as an electrical circuit.

Accepted Answer

A) True 
 B)False

Question 9

Schematic diagram is used to show the relationship of the components and equipment located in the substation.

Accepted Answer

A) True 
 B)False

Question 10

All electronic component values are extremely large (2,500,000,000,000).

Accepted Answer

A) True 
 B)False

Question 11

The ____________________ combines the simplicity of a schematic diagram and the completeness of a wiring diagram. The complete circuit is drawn as a series of lines and symbols that represent the electrical current path and the components of the circuit. Connection terminals are shown in their proper locations along the circuit.

Accepted Answer

schematic

Question 12

Printed circuit boards do not need to have separate mounting holes for each component lead or terminal.

Accepted Answer

A) True 
 B)False

Question 13

A coil is a conductor wound on a form or in a spiral that has inductive properties.

Accepted Answer

A) True 
 B)False

Question 14

DC refers to what?

Accepted Answer

The answer of DC refers to what?...

Question 15

____ is the control of electrons for use in devices that are dependent on low voltage, amperage, and signal paths.

Accepted Answer

A)  Electricity 
B)  Electrical schematics 
C)  Electrical layout 
D)  Grounding 
E)  none of the above 
A)  Electricity 
B)  Electrical schematics 
C)  Electrical layout 
D)  Grounding 
E)  none of the above

Question 16

There are separate terminal pads for each component lead or wire attachment on printed circuit boards.

Accepted Answer

A) True 
 B)False

Question 17

____ provide the path for electrical flow from the source of electricity through system components and connections and back to the source.

Accepted Answer

A)  Wiring diagrams 
B)  Highway wiring diagrams 
C)  Cable diagrams 
D)  One line diagrams 
E)  none of the above 
A)  Wiring diagrams 
B)  Highway wiring diagrams 
C)  Cable diagrams 
D)  One line diagrams 
E)  none of the above

Question 18

____________________ is a flat plate or base of insulating material containing a pattern of conducting material and becomes an electrical circuit when components are attached.

Accepted Answer

printed ci

Question 19

MATCHING
Match the type of diagram with its description.
-The complete circuit is drawn showing the electrical current path and the components of the circuit

Accepted Answer

A) pictorial 
B) schematic 
C) block 
D) wiring 
E) schematic wiring
F)highway wiring
G)wireless
H)cable 
A) pictorial 
B) schematic 
C) block 
D) wiring 
E) schematic wiring
F)highway wiring
G)wireless
H)cable

Question 20

Which of the following is not included in a parts list?

Accepted Answer

A)  quantity of a part 
B)  part number 
C)  item identification keyed to the assembly 
D)  electronic designations for components 
E)  none of the above 
A)  quantity of a part 
B)  part number 
C)  item identification keyed to the assembly 
D)  electronic designations for components 
E)  none of the above

Platform pattern, flat pack pattern, and terminal area shapes are all examples of ____.

The placement of identification numbers of electronic components is variable.

Cables are ____.

MATCHING Match the type of diagram with its description. -Represents the electrical circuit as a three dimensional drawing

MATCHING Match the type of diagram with its description. -Shows the components but the interconnecting lines are omitted

The basic circuitry that makes any electronic device function is known as the ____.

____ have conductive material plated on the inside wall to form a conductive connection between layers of the circuit board.

An electrical system is the same thing as an electrical circuit.

Schematic diagram is used to show the relationship of the components and equipment located in the substation.

All electronic component values are extremely large (2,500,000,000,000).

Printed circuit boards do not need to have separate mounting holes for each component lead or terminal.

A coil is a conductor wound on a form or in a spiral that has inductive properties.

DC refers to what?

____ is the control of electrons for use in devices that are dependent on low voltage, amperage, and signal paths.

There are separate terminal pads for each component lead or wire attachment on printed circuit boards.

____ provide the path for electrical flow from the source of electricity through system components and connections and back to the source.

____________________ is a flat plate or base of insulating material containing a pattern of conducting material and becomes an electrical circuit when components are attached.

MATCHING Match the type of diagram with its description. -The complete circuit is drawn showing the electrical current path and the components of the circuit

Which of the following is not included in a parts list?

Introduction to Engineering and Manufacturing Technology Print Reading

Communicating with a Sketch

Scales and Precision Measurement

Reading Lines and Lettering on a Print

Reading Multiviews

Reading Auxiliary Views

Manufacturing Materials and Processes

Reading Dimensions

Reading Prints With Fasteners and Springs

Reading Sections, Revolutions, and Conventional Breaks

Reading Geometric Dimensioning and Tolerancing

Reading Linkage, Cam, Gear, and Bearing Prints

Reading Precision Sheet Metal Prints

Reading Prints of Working Drawings

Welding Processes and Reading Welding Representations

Reading Prints of Pictorial Drawings

Filters

Exam 17: Reading Electrical Diagrams and Schematics

Platform pattern, flat pack pattern, and terminal area shapes are all examples of ____.

The placement of identification numbers of electronic components is variable.

Cables are ____.

MATCHING Match the type of diagram with its description. -Represents the electrical circuit as a three dimensional drawing

MATCHING Match the type of diagram with its description. -Shows the components but the interconnecting lines are omitted

The basic circuitry that makes any electronic device function is known as the ____.

____ have conductive material plated on the inside wall to form a conductive connection between layers of the circuit board.

An electrical system is the same thing as an electrical circuit.

Schematic diagram is used to show the relationship of the components and equipment located in the substation.

All electronic component values are extremely large (2,500,000,000,000).

Printed circuit boards do not need to have separate mounting holes for each component lead or terminal.

A coil is a conductor wound on a form or in a spiral that has inductive properties.

DC refers to what?

____ is the control of electrons for use in devices that are dependent on low voltage, amperage, and signal paths.

There are separate terminal pads for each component lead or wire attachment on printed circuit boards.

____ provide the path for electrical flow from the source of electricity through system components and connections and back to the source.

____________________ is a flat plate or base of insulating material containing a pattern of conducting material and becomes an electrical circuit when components are attached.

MATCHING Match the type of diagram with its description. -The complete circuit is drawn showing the electrical current path and the components of the circuit

Which of the following is not included in a parts list?

Introduction to Engineering and Manufacturing Technology Print Reading

Communicating with a Sketch

Scales and Precision Measurement

Reading Lines and Lettering on a Print

Reading Multiviews

Reading Auxiliary Views

Manufacturing Materials and Processes

Reading Dimensions

Reading Prints With Fasteners and Springs

Reading Sections, Revolutions, and Conventional Breaks

Reading Geometric Dimensioning and Tolerancing

Reading Linkage, Cam, Gear, and Bearing Prints

Reading Precision Sheet Metal Prints

Reading Prints of Working Drawings

Welding Processes and Reading Welding Representations

Reading Prints of Pictorial Drawings

Filters