Question 1

The ____ is used for fabrication, quality control, and troubleshooting of the wiring of electrical circuits and systems.

Accepted Answer

A)  One line diagram 
B)  pictorial diagram 
C)  wireless diagram 
D)  wiring diagram 
E)  none of the above 
A)  One line diagram 
B)  pictorial diagram 
C)  wireless diagram 
D)  wiring diagram 
E)  none of the above

Question 2

The printed circuit board assembly drawing is a complete engineering drawing, including components, assembly and fastening or soldering specifications, and a parts list or bill of materials.

Accepted Answer

A) True 
 B)False

Question 3

The ____________________ is a simplified version of the schematic diagram. Simplified symbols exhibit a minimum of detail of the component and generally no connections at individual terminals.

Accepted Answer

The answer of The ____________________ is a simplified version of...

Question 4

The ____ consist of pads and conductor lines that are made of thin conductive material such as copper on a base sheet or board.

Accepted Answer

A)  printed circuits 
B)  circuit board 
C)  master pattern 
D)  conductor 
E)  none of the above 
A)  printed circuits 
B)  circuit board 
C)  master pattern 
D)  conductor 
E)  none of the above

Question 5

A 34000 ohm resistor is the same as a 3.4k ohm resistor.

Accepted Answer

A) True 
 B)False

Question 6

MATCHING
Match the type of diagram with its description.
-Used for fabrication, quality control and troubleshooting

Accepted Answer

A) pictorial 
B) schematic 
C) block 
D) wiring 
E) schematic wiring
F)highway wiring
G)wireless
H)cable 
A) pictorial 
B) schematic 
C) block 
D) wiring 
E) schematic wiring
F)highway wiring
G)wireless
H)cable

Question 7

A ________________ is a cable or group of insulated wires put together in one sealed assembly.

Accepted Answer

The answer of A ________________ is a cable or group...

Question 8

If J = 6 times 10 to the power of 7, and K = 3 times 10 to the power of 3, then what is the answer if J is divided by K?

Accepted Answer

A)  18 times 10 to the power of 4 
B)  18 times 10 to the power of 6 
C)  18 times 10 to the power of 10 
D)  2 times 10 to the power of 4 
E)  none of the above 
A)  18 times 10 to the power of 4 
B)  18 times 10 to the power of 6 
C)  18 times 10 to the power of 10 
D)  2 times 10 to the power of 4 
E)  none of the above

Question 9

____________________ are drawn as a series of lines and symbols representing the electrical current path and the components of the circuit.

Accepted Answer

The answer of ____________________ are drawn as a series of...

Question 10

The ____________________, also known as_____________________, are used for fabrication, quality control, and troubleshooting of the wiring of electrical circuits and systems. A highway wiring diagram is a simplified or condensed representation of a point-to-point interconnecting wiring diagram, and can be used when it becomes difficult to draw individual connection lines because of diagram complexity or when it is not necessary to show all of the wires between terminal blocks.

Accepted Answer

Highway wi

Question 11

A ____ is a device that provides a degree of resistance in an electronic circuit, and under certain conditions either allows current to pass through it freely or blocks the flow completely.

Accepted Answer

A)  capacitor 
B)  semiconductor 
C)  inductor 
D)  coil 
E)  none of the above 
A)  capacitor 
B)  semiconductor 
C)  inductor 
D)  coil 
E)  none of the above

Question 12

A(n) ____ is an electronic component that contains voltage or current sources, such as a transistor and integrated circuit.

Accepted Answer

A)  active device 
B)  bias circuitry 
C)  coupling circuitry 
D)  transistor bias circuit 
E)  none of the above 
A)  active device 
B)  bias circuitry 
C)  coupling circuitry 
D)  transistor bias circuit 
E)  none of the above

Question 13

A ____ is a group of insulated wires put together in one sealed assembly.

Accepted Answer

A)  truck line 
B)  feed line 
C)  Multi-conductor 
D)  substation 
E)  none of the above 
A)  truck line 
B)  feed line 
C)  Multi-conductor 
D)  substation 
E)  none of the above

Question 14

____________________ is the control of electrons for use in devices that are dependent on low voltage, amperage and signal paths.

Accepted Answer

The answer of ____________________ is the control of electrons for...

Question 15

Define active device.

Accepted Answer

An active device is an electro

Question 16

If Q = 1.4 times 10 to the power of 15, and R = 2 times 10 to the power of negative 5, then what is the answer if Q is divided by R?

Accepted Answer

A)  7 times 10 to the power of 10 
B)  7 times 10 to the power of 11 
C)  7 times 10 to the power of 18 
D)  7 times 10 to the power of 20 
E)  none of the above 
A)  7 times 10 to the power of 10 
B)  7 times 10 to the power of 11 
C)  7 times 10 to the power of 18 
D)  7 times 10 to the power of 20 
E)  none of the above

Question 17

Define fault condition.

Accepted Answer

A fault condition is

Question 18

Surface mounted devices commonly take up to three times the space of feed through printed circuits.

Accepted Answer

A) True 
 B)False

Question 19

Electrical diagrams are generally drawn to scale.

Accepted Answer

A) True 
 B)False

Question 20

The designating system has developed around a letter indicating the type of component followed by a number that gives the sequence of the part in the circuit.

Accepted Answer

A) True 
 B)False

The ____ is used for fabrication, quality control, and troubleshooting of the wiring of electrical circuits and systems.

The printed circuit board assembly drawing is a complete engineering drawing, including components, assembly and fastening or soldering specifications, and a parts list or bill of materials.

The ____________________ is a simplified version of the schematic diagram. Simplified symbols exhibit a minimum of detail of the component and generally no connections at individual terminals.

The ____ consist of pads and conductor lines that are made of thin conductive material such as copper on a base sheet or board.

A 34000 ohm resistor is the same as a 3.4k ohm resistor.

MATCHING Match the type of diagram with its description. -Used for fabrication, quality control and troubleshooting

A ________________ is a cable or group of insulated wires put together in one sealed assembly.

If J = 6 times 10 to the power of 7, and K = 3 times 10 to the power of 3, then what is the answer if J is divided by K?

____________________ are drawn as a series of lines and symbols representing the electrical current path and the components of the circuit.

A ____ is a device that provides a degree of resistance in an electronic circuit, and under certain conditions either allows current to pass through it freely or blocks the flow completely.

A(n) ____ is an electronic component that contains voltage or current sources, such as a transistor and integrated circuit.

A ____ is a group of insulated wires put together in one sealed assembly.

____________________ is the control of electrons for use in devices that are dependent on low voltage, amperage and signal paths.

Define active device.

If Q = 1.4 times 10 to the power of 15, and R = 2 times 10 to the power of negative 5, then what is the answer if Q is divided by R?

Define fault condition.

Surface mounted devices commonly take up to three times the space of feed through printed circuits.

Electrical diagrams are generally drawn to scale.

The designating system has developed around a letter indicating the type of component followed by a number that gives the sequence of the part in the circuit.

Introduction to Engineering and Manufacturing Technology Print Reading

Communicating with a Sketch

Scales and Precision Measurement

Reading Lines and Lettering on a Print

Reading Multiviews

Reading Auxiliary Views

Manufacturing Materials and Processes

Reading Dimensions

Reading Prints With Fasteners and Springs

Reading Sections, Revolutions, and Conventional Breaks

Reading Geometric Dimensioning and Tolerancing

Reading Linkage, Cam, Gear, and Bearing Prints

Reading Precision Sheet Metal Prints

Reading Prints of Working Drawings

Welding Processes and Reading Welding Representations

Reading Prints of Pictorial Drawings

Filters

Exam 17: Reading Electrical Diagrams and Schematics

The ____ is used for fabrication, quality control, and troubleshooting of the wiring of electrical circuits and systems.

The printed circuit board assembly drawing is a complete engineering drawing, including components, assembly and fastening or soldering specifications, and a parts list or bill of materials.

The ____________________ is a simplified version of the schematic diagram. Simplified symbols exhibit a minimum of detail of the component and generally no connections at individual terminals.

The ____ consist of pads and conductor lines that are made of thin conductive material such as copper on a base sheet or board.

A 34000 ohm resistor is the same as a 3.4k ohm resistor.

MATCHING Match the type of diagram with its description. -Used for fabrication, quality control and troubleshooting

A ________________ is a cable or group of insulated wires put together in one sealed assembly.

If J = 6 times 10 to the power of 7, and K = 3 times 10 to the power of 3, then what is the answer if J is divided by K?

____________________ are drawn as a series of lines and symbols representing the electrical current path and the components of the circuit.

A ____ is a device that provides a degree of resistance in an electronic circuit, and under certain conditions either allows current to pass through it freely or blocks the flow completely.

A(n) ____ is an electronic component that contains voltage or current sources, such as a transistor and integrated circuit.

A ____ is a group of insulated wires put together in one sealed assembly.

____________________ is the control of electrons for use in devices that are dependent on low voltage, amperage and signal paths.

Define active device.

If Q = 1.4 times 10 to the power of 15, and R = 2 times 10 to the power of negative 5, then what is the answer if Q is divided by R?

Define fault condition.

Surface mounted devices commonly take up to three times the space of feed through printed circuits.

Electrical diagrams are generally drawn to scale.

The designating system has developed around a letter indicating the type of component followed by a number that gives the sequence of the part in the circuit.

Introduction to Engineering and Manufacturing Technology Print Reading

Communicating with a Sketch

Scales and Precision Measurement

Reading Lines and Lettering on a Print

Reading Multiviews

Reading Auxiliary Views

Manufacturing Materials and Processes

Reading Dimensions

Reading Prints With Fasteners and Springs

Reading Sections, Revolutions, and Conventional Breaks

Reading Geometric Dimensioning and Tolerancing

Reading Linkage, Cam, Gear, and Bearing Prints

Reading Precision Sheet Metal Prints

Reading Prints of Working Drawings

Welding Processes and Reading Welding Representations

Reading Prints of Pictorial Drawings

Filters