Question 1

Refer to the exhibit. Which statement about this configuration is true?

Accepted Answer

A)  Router 1 sends and receives multiple best paths from neighbor 192.168.1.1 
B)  Router 1 sends up to two paths to neighbor 192.168.1.1 for all routes 
C)  Router 1 receives up to two paths from neighbor 192.168.1.1 for all routes in the same AS 
D)  Router 1 receives only the best path from neighbor 192.168.1.1 
A)  Router 1 sends and receives multiple best paths from neighbor 192.168.1.1 
B)  Router 1 sends up to two paths to neighbor 192.168.1.1 for all routes 
C)  Router 1 receives up to two paths from neighbor 192.168.1.1 for all routes in the same AS 
D)  Router 1 receives only the best path from neighbor 192.168.1.1

Question 2

Which statement about enabling segment routing for IGPs is true?

Accepted Answer

A)  Segment routing must first be enabled under then routing process and then globally 
B)  Segment routing must first be enabled globally and then under the routing process 
C)  Segment routing can be enabled only under the routing process 
D)  Segment routing can be enabled only globally 
A)  Segment routing must first be enabled under then routing process and then globally 
B)  Segment routing must first be enabled globally and then under the routing process 
C)  Segment routing can be enabled only under the routing process 
D)  Segment routing can be enabled only globally

Question 3

Refer to the exhibit. An engineer applied the summarization configuration on R1 for four networks (192.168.20.0/24 to 192.168.23.0/24) in area 1 and eight networks (192.168.32.0/24 to 192.168.39.0/24) in area 2 to stop the flooding of all the customer routes. While checking the routing table of R2, the engineer noticed that R1 is still sending only specific routes to R2. Which configuration should the engineer apply on R1 to summarize routes?

Accepted Answer

A)    
B)    
C)    
D)    
A)    
B)    
C)    
D)

Question 4

Refer to the exhibit. After troubleshooting an OSPF adjacency issue, routers 1, 2, and 3 have formed OSPF neighbor relationships. Which statement about the configuration is true?

Accepted Answer

A)  Router 2 receives a Type 5 LSAs from router 1 for its connected subnets 
B)  Router 2 uses router 3 as the next hop for 192.168.0.0/24 
C)  Router 2 uses router 1 as the next hop for 192.168.0.0/24 
D)  Router 2 receives a Type 7 LSAs from router 3 for its connected subnets 
A)  Router 2 receives a Type 5 LSAs from router 1 for its connected subnets 
B)  Router 2 uses router 3 as the next hop for 192.168.0.0/24 
C)  Router 2 uses router 1 as the next hop for 192.168.0.0/24 
D)  Router 2 receives a Type 7 LSAs from router 3 for its connected subnets

Question 5

Refer to the exhibit. Which tree does multicast traffic follow?

Accepted Answer

A)  shared tree 
B)  MDT default 
C)  source tree 
D)  MDT voice 
A)  shared tree 
B)  MDT default 
C)  source tree 
D)  MDT voice

Question 6

Refer to the exhibit. Which router does R1 install as an alternate next hop when trying to reach R3 if LFA is enabled?

Accepted Answer

A)  R5 
B)  R3 
C)  R4 
D)  R2 
A)  R5 
B)  R3 
C)  R4 
D)  R2

Question 7

What can be used to determine a path from the head-end to a tail-end router when implementing SR-TE with a head-end, with little information on the network topology?

Accepted Answer

A)  traffic controller 
B)  path computation engine 
C)  tail-end router 
D)  SNMP server 
A)  traffic controller 
B)  path computation engine 
C)  tail-end router 
D)  SNMP server

Question 8

You have configured routing policies on a Cisco IOS XR device with routing policy language. Which two statements about the routing policies are true? (Choose two.)

Accepted Answer

A)  The routing policies affect BGP-related routes only. 
B)  If you make edits to an existing routing policy without pasting the full policy into the CLI, the previous policy is overwritten. 
C)  You can change an existing routing policy by editing individual statements. 
D)  The routing policies are implemented in a sequential manner. 
E)  The routing policies are implemented using route maps. 
A)  The routing policies affect BGP-related routes only. 
B)  If you make edits to an existing routing policy without pasting the full policy into the CLI, the previous policy is overwritten. 
C)  You can change an existing routing policy by editing individual statements. 
D)  The routing policies are implemented in a sequential manner. 
E)  The routing policies are implemented using route maps.

Question 9

Refer to the exhibit. Router 1 has attempted to establish a Cisco MPLS TE tunnel to router 2, but the tunnel has failed. Which statement about this configuration is true?

Accepted Answer

A)  Router 1 must define an explicit path to router 2 
B)  Router 1 and router 2 must define the RSVP bandwidth reserved on the physical interfaces 
C)  Router 2 must have a tunnel interface created with router 1 as the destination 
D)  Router 1 must have Cisco MPLS TE enabled on interface gigabitethernet0/1 
A)  Router 1 must define an explicit path to router 2 
B)  Router 1 and router 2 must define the RSVP bandwidth reserved on the physical interfaces 
C)  Router 2 must have a tunnel interface created with router 1 as the destination 
D)  Router 1 must have Cisco MPLS TE enabled on interface gigabitethernet0/1

Question 10

Refer to the exhibit. A network operator is working to filter routes from being advertised that are covered under an aggregate announcement. The receiving router of the aggregate announcement block is still getting some of the more specific routes plus the aggregate. Which configuration change ensures that only the aggregate is announced now and in the future if other networks are to be added?

Accepted Answer

A)  Configure the summary-only keyword on the aggregate command Configure the summary-only keyword on the aggregate command 
B)  Set each specific route in the AGGRO policy to drop instead of suppress-route 
C)  Filter the routes on the receiving router 
D)  Set each specific route in the AGGRO policy to remove instead of suppress-route 
A)  Configure the summary-only keyword on the aggregate command Configure the summary-only keyword on the aggregate command 
B)  Set each specific route in the AGGRO policy to drop instead of suppress-route 
C)  Filter the routes on the receiving router 
D)  Set each specific route in the AGGRO policy to remove instead of suppress-route

Question 11

Refer to the exhibit. An administrator is troubleshooting Internet access issues on a customer's network. After applying this ISIS configuration to R1, the administrator notices that it fails to redistribute the default route into IS-IS. After checking the connectivity between the ISIS router and the ISP router the engineer confirmed there is Layer 3 connectivity between them. Which action should be taken to correct the problem?

Accepted Answer

A)  Configure R1 as a Layer 1 router 
B)  Add the default-information originate command to the configuration Add the default-information originate command to the configuration 
C)  ?onfigure the default route under any routing protocol other than IS-IS 
D)  Associate the default route with a VRF 
A)  Configure R1 as a Layer 1 router 
B)  Add the default-information originate command to the configuration Add the default-information originate command to the configuration 
C)  ?onfigure the default route under any routing protocol other than IS-IS 
D)  Associate the default route with a VRF

Question 12

An engineer is troubleshooting slow performance issues on a customer's network after the last multicast configuration change was applied on it. While checking the running configuration on the router, the engineer notices there are many ip igmp join-group commands applied on several interfaces of the router which caused the high CPU utilization usage. What action must the engineer take to solve this issue?

Accepted Answer

A)  Configure all router interfaces to be process-switched by increasing the query interval 
B)  Remove ip igmp join-group command on all unnecessary interfaces Remove command on all unnecessary interfaces 
C)  Remove unnecessary members from the IGMP group 
D)  Configure ip igmp static-group command on all interfaces Configure ip igmp static-group command on all interfaces 
A)  Configure all router interfaces to be process-switched by increasing the query interval 
B)  Remove ip igmp join-group command on all unnecessary interfaces Remove command on all unnecessary interfaces 
C)  Remove unnecessary members from the IGMP group 
D)  Configure ip igmp static-group command on all interfaces Configure ip igmp static-group command on all interfaces

Question 13

In a PIM-SM environment, which mechanism determines the traffic that a receiver receives?

Accepted Answer

A)  The receiver explicitly requests its desired traffic from the RP on the shared tree. 
B)  The receiver explicitly requests traffic from a single source, which responds by forwarding all traffic. 
C)  The RP on the shared tree floods traffic out of all PIM configured interfaces. 
D)  The receiver explicitly requests traffic from each desired source, which responds by sending all traffic. 
A)  The receiver explicitly requests its desired traffic from the RP on the shared tree. 
B)  The receiver explicitly requests traffic from a single source, which responds by forwarding all traffic. 
C)  The RP on the shared tree floods traffic out of all PIM configured interfaces. 
D)  The receiver explicitly requests traffic from each desired source, which responds by sending all traffic.

Question 14

Refer to the exhibit. Why is neighbor 10.1.5.5 stuck in "2WAY" state?

Accepted Answer

A)  Router ID 10.1.5.5 is not reachable from R2 
B)  OSPF authentication has failed between R2 and 10.1.5.5 
C)  It is an expected behavior when OSPF network type is broadcast 
D)  OSPF parameters (Area ID or hello interval) are mismatched between R2 and 10.1.5.5 
A)  Router ID 10.1.5.5 is not reachable from R2 
B)  OSPF authentication has failed between R2 and 10.1.5.5 
C)  It is an expected behavior when OSPF network type is broadcast 
D)  OSPF parameters (Area ID or hello interval) are mismatched between R2 and 10.1.5.5

Question 15

Refer to the exhibit. Router 1 is a core ABR in a Cisco Unified MPLS environment. All of the router 1 BGP peers are established, but traffic between customers is failing. Which BGP configuration must be added to the configuration?

Accepted Answer

A)  It must be configured for graceful restart 
B)  It must be configured with a route reflector 
C)  It must be configured with send labels 
D)  It must be configured with PIC edge 
A)  It must be configured for graceful restart 
B)  It must be configured with a route reflector 
C)  It must be configured with send labels 
D)  It must be configured with PIC edge

Question 16

Which command is used to enable BIDIR-PIM under global configuration mode for Cisco IOS XE Sofware?

Accepted Answer

A)  ip pim bidir-enable 
B)  ipv4 pim bidir-enable 
C)  ip multicast-routing 
D)  ip pim bidir 
A)  ip pim bidir-enable 
B)  ipv4 pim bidir-enable 
C)  ip multicast-routing 
D)  ip pim bidir

Question 17

Refer to the exhibit. R1 is directly connected to R2 and R3. R1 is in BGP AS 123, R2 is in BGP AS 2, and R3 is in BGP AS 3. Assume that there is no connectivity issue between R1, R2 and R1, R3. Which result between BGP peers R1, R2 and R1, R3 is true?

Accepted Answer

A)  The BGP session does not come up between R1 and R2 and between R1 and R3. 
B)  The BGP session comes up between R1 and R2 and between R1 and R3. 
C)  The BGP session comes up between R1 and R3, but not between R1 and R2. 
D)  The BGP session comes up between R1 and R2, but not between R1 and R3. 
A)  The BGP session does not come up between R1 and R2 and between R1 and R3. 
B)  The BGP session comes up between R1 and R2 and between R1 and R3. 
C)  The BGP session comes up between R1 and R3, but not between R1 and R2. 
D)  The BGP session comes up between R1 and R2, but not between R1 and R3.

Question 18

Which two conditions must be met before separate ISPs can provide interdomain multicast routing? (Choose two.)

Accepted Answer

A)  Each ISP must configure MSDP to connect its individual multicast administrative domain to the domains at other ISPs. 
B)  Each ISP must dedicate a single router to handle multicast traffic between providers. 
C)  Each ISP must replace its RP assignment with a global RP. 
D)  Each ISP must configure its network to use PIM-DM. 
E)  Each ISP must support intradomain multicast routing. 
A)  Each ISP must configure MSDP to connect its individual multicast administrative domain to the domains at other ISPs. 
B)  Each ISP must dedicate a single router to handle multicast traffic between providers. 
C)  Each ISP must replace its RP assignment with a global RP. 
D)  Each ISP must configure its network to use PIM-DM. 
E)  Each ISP must support intradomain multicast routing.

Question 19

Which two statements about mapping multicast IP addresses to MAC addresses are true? (Choose two.)

Accepted Answer

A)  All mapped multicast MAC addresses begin with 0x0100.5E 
B)  The router performs the mapping before it hands the packet off to a switch 
C)  All multicast MAC addresses end with 0x0100.5E 
D)  The mapping process may generate overlapping addresses, which can cause receivers to receive unwanted packets 
E)  All destination MAC addresses begin with an octet of binary 1s 
A)  All mapped multicast MAC addresses begin with 0x0100.5E 
B)  The router performs the mapping before it hands the packet off to a switch 
C)  All multicast MAC addresses end with 0x0100.5E 
D)  The mapping process may generate overlapping addresses, which can cause receivers to receive unwanted packets 
E)  All destination MAC addresses begin with an octet of binary 1s

Question 20

Refer to the exhibit. A network engineer applied configuration on R1 to summarize all ISIS routes, but R2 is still receiving specific routes from R1. The engineer has confirmed that both routers are configured with the correct summarization configuration, but R1 is not sending the correct summary routes. Which configuration must be applied to router R1 to summarize routes within Level 1?

Accepted Answer

A)  R1(config-router)# no summary-address 1.0.0.0 255.0.0.0 level-1 R1(config-router)# no summary-address 1.0.0.0 255.0.0.0 level-1 
B)  R1(config-router)# summary-address 1.0.0.0 255.0.0.0 level-2 summary-address 1.0.0.0 255.0.0.0 level-2 
C)  R1(config-router)# summary-address 1.0.0.0 255.0.0.0 level-1-2 summary-address 1.0.0.0 255.0.0.0 level-1-2 
D)  R1(config-router)# summary-address 1.0.0.0 255.0.0.0 level-1 summary-address 1.0.0.0 255.0.0.0 level-1 
A)  R1(config-router)# no summary-address 1.0.0.0 255.0.0.0 level-1 R1(config-router)# no summary-address 1.0.0.0 255.0.0.0 level-1 
B)  R1(config-router)# summary-address 1.0.0.0 255.0.0.0 level-2 summary-address 1.0.0.0 255.0.0.0 level-2 
C)  R1(config-router)# summary-address 1.0.0.0 255.0.0.0 level-1-2 summary-address 1.0.0.0 255.0.0.0 level-1-2 
D)  R1(config-router)# summary-address 1.0.0.0 255.0.0.0 level-1 summary-address 1.0.0.0 255.0.0.0 level-1

Exam 14: Implementing Cisco Service Provider Advanced Routing Solutions (SPRI)

Refer to the exhibit. Which statement about this configuration is true?

Which statement about enabling segment routing for IGPs is true?

Refer to the exhibit. After troubleshooting an OSPF adjacency issue, routers 1, 2, and 3 have formed OSPF neighbor relationships. Which statement about the configuration is true?

Refer to the exhibit. Which tree does multicast traffic follow?

Refer to the exhibit. Which router does R1 install as an alternate next hop when trying to reach R3 if LFA is enabled?

What can be used to determine a path from the head-end to a tail-end router when implementing SR-TE with a head-end, with little information on the network topology?

You have configured routing policies on a Cisco IOS XR device with routing policy language. Which two statements about the routing policies are true? (Choose two.)

Refer to the exhibit. Router 1 has attempted to establish a Cisco MPLS TE tunnel to router 2, but the tunnel has failed. Which statement about this configuration is true?

In a PIM-SM environment, which mechanism determines the traffic that a receiver receives?

Refer to the exhibit. Why is neighbor 10.1.5.5 stuck in "2WAY" state?

Refer to the exhibit. Router 1 is a core ABR in a Cisco Unified MPLS environment. All of the router 1 BGP peers are established, but traffic between customers is failing. Which BGP configuration must be added to the configuration?

Which command is used to enable BIDIR-PIM under global configuration mode for Cisco IOS XE Sofware?

Refer to the exhibit. R1 is directly connected to R2 and R3. R1 is in BGP AS 123, R2 is in BGP AS 2, and R3 is in BGP AS 3. Assume that there is no connectivity issue between R1, R2 and R1, R3. Which result between BGP peers R1, R2 and R1, R3 is true?

Which two conditions must be met before separate ISPs can provide interdomain multicast routing? (Choose two.)

Which two statements about mapping multicast IP addresses to MAC addresses are true? (Choose two.)

Supporting Cisco Data Center System Devices (DCTECH)

Cisco Certified Technician Routing & Switching (RSTECH)

Understanding Cisco Cybersecurity Operations Fundamentals (CBROPS)

Cisco Certified Network Associate (CCNA)

Managing Industrial Networks with Cisco Networking Technologies (IMINS)

DevNet Associate (DEVASC)

Conducting Forensic Analysis and Incident Response Using Cisco CyberOps Technologies (CBRFIR)

Implementing Cisco Enterprise Advanced Routing and Services (ENARSI)

Implementing Cisco SD-WAN Solutions (ENSDWI)

Designing Cisco Enterprise Networks (ENSLD)

Designing Cisco Enterprise Wireless Networks (300-425 ENWLSD)

Implementing Cisco Enterprise Wireless Networks (300-430 ENWLSI)

Automating Cisco Enterprise Solutions (ENAUTO)

Implementing Cisco Service Provider VPN Services (SPVI)

Designing Cisco Data Center Infrastructure (DCID)

Troubleshooting Cisco Data Center Infrastructure (DCIT)

Implementing Cisco Application Centric Infrastructure (DCACI)

Configuring Cisco MDS 9000 Series Switches (DCSAN)

Implementing Cisco Application Centric Infrastructure - Advanced

Automating Cisco Data Center Solutions (DCAUTO)

Securing Networks with Cisco Firepower (300-710 SNCF)

Implementing and Configuring Cisco Identity Services Engine (300-715 SISE)

Securing Email with Cisco Email Security Appliance (300-720 SESA)

Securing the Web with Cisco Web Security Appliance (300-725 SWSA)

Implementing Secure Solutions with Virtual Private Networks (SVPN 300-730)

Automating Cisco Security Solutions (SAUTO)

Implementing Cisco Collaboration Applications (CLICA)

Implementing Cisco Advanced Call Control and Mobility Services (CLASSM)

Implementing Cisco Collaboration Cloud and Edge Solutions

Implementing Cisco Collaboration Conferencing

Automating Cisco Collaboration Solutions (CLAUTO)

Implementing DevOps Solutions and Practices using Cisco Platforms (DEVOPS)

Developing Solutions Using Cisco IoT and Edge Platforms (DEVIOT)

Developing Applications for Cisco Webex and Webex Devices (DEVWBX)

Performing CyberOps Using Core Security Technologies (CBRCOR)

Implementing Cisco Enterprise Network Core Technologies (ENCOR)

Implementing and Operating Cisco Service Provider Network Core Technologies (SPCOR)

Implementing and Operating Cisco Data Center Core Technologies (DCCOR)

Implementing and Operating Cisco Security Core Technologies

Implementing Cisco Collaboration Core Technologies (CLCOR)

Developing Applications using Cisco Core Platforms and APIs (DEVCOR)

CCDE Design Written

Deploying Cisco Unified Contact Center Express

Cisco Meraki Solutions Specialist

Securing Cisco Networks with Sourcefire FireAMP Endpoints

Designing Cisco Unified Contact Center Enterprise (UCCED)

Implementing and Supporting Cisco Unified Contact Center Enterprise (UCCEIS)

Cisco Collaboration SaaS Authorization Exam

Cisco Security Architecture for System Engineers

Adopting The Cisco Business Architecture Approach (DTBAA)

Cisco Customer Success Manager (CSM)

Mastering The Cisco Business Architecture Discipline (DTBAD)

Filters