Question 1

When the range of process variation is larger than the design specifications, the process capability index will be less than 1.

Accepted Answer

A) True 
 B)False

Question 2

Indications in a control chart of an out-of-control situation include all of the following except

Accepted Answer

A) Six or seven consecutive points that increase or decrease in value 
B) About the same number of points above and below the center line 
C) There are points outside control limits 
D) There are no more points near the center line than there are close to the control limits 
A) Six or seven consecutive points that increase or decrease in value 
B) About the same number of points above and below the center line 
C) There are points outside control limits 
D) There are no more points near the center line than there are close to the control limits

Question 3

Which one of the following statements is true?

Accepted Answer

A) Common cause variation arises from external sources that are not inherent in the process and is where statistical quality control methods are most useful. 
B) If the metric is discrete, a p- or c-chart is normally used. 
C) Statistical process control is not used in hospitals due to the high liability costs. 
D) Statistical process control charts are used when trying to monitor and control 5- and 6-sigma quality levels. 
A) Common cause variation arises from external sources that are not inherent in the process and is where statistical quality control methods are most useful. 
B) If the metric is discrete, a p- or c-chart is normally used. 
C) Statistical process control is not used in hospitals due to the high liability costs. 
D) Statistical process control charts are used when trying to monitor and control 5- and 6-sigma quality levels.

Question 4

Explain and give the significance of the 1:10:100 Rule.

Accepted Answer

If a defect or service error is identifi

Question 5

In the 1:10:100 Rule, which of the following would be correct?

Accepted Answer

A) If a defect or service error is identified and corrected at the design stage, it might cost $100 to fix. 
B) If a defect or service error is identified and corrected at the production process stage, it might cost $100 to fix. 
C) If a defect or service error is identified and corrected after it reaches the customer, it might cost $100 to fix. 
D) If a defect or service error is identified and corrected at the design stage, it might cost $1$\times$$10$\times$$100 = $1,000 to fix. 
A) If a defect or service error is identified and corrected at the design stage, it might cost $100 to fix. 
B) If a defect or service error is identified and corrected at the production process stage, it might cost $100 to fix. 
C) If a defect or service error is identified and corrected after it reaches the customer, it might cost $100 to fix. 
D) If a defect or service error is identified and corrected at the design stage, it might cost $1$\times$$10$\times$$100 = $1,000 to fix.

When the range of process variation is larger than the design specifications, the process capability index will be less than 1.

Indications in a control chart of an out-of-control situation include all of the following except

Which one of the following statements is true?

Explain and give the significance of the 1:10:100 Rule.

In the 1:10:100 Rule, which of the following would be correct?

Goods, Services, and Operations Management

Value Chains

Measuring Performance in Operations

Operations Strategy

Technology and Operations Management

Goods and Service Design

Process Selection, Design, and Analysis

Facility and Work Design

Supply Chain Design

Capacity Management

Forecasting and Demand Planning

Managing Inventories

Resource Management

Operations Scheduling and Sequencing

Quality Management

Lean Operating Systems

Project Management

Work Measurement, Learning Curves, and Standards

Queuing Analysis

Modeling Using Linear Programming

Simulation

Decision Analysis

Filters

Exam 16: Quality Control and Spc

When the range of process variation is larger than the design specifications, the process capability index will be less than 1.

Indications in a control chart of an out-of-control situation include all of the following except

Which one of the following statements is true?

Explain and give the significance of the 1:10:100 Rule.

In the 1:10:100 Rule, which of the following would be correct?

Goods, Services, and Operations Management

Value Chains

Measuring Performance in Operations

Operations Strategy

Technology and Operations Management

Goods and Service Design

Process Selection, Design, and Analysis

Facility and Work Design

Supply Chain Design

Capacity Management

Forecasting and Demand Planning

Managing Inventories

Resource Management

Operations Scheduling and Sequencing

Quality Management

Lean Operating Systems

Project Management

Work Measurement, Learning Curves, and Standards

Queuing Analysis

Modeling Using Linear Programming

Simulation

Decision Analysis

Filters