Exam 9: Rotation of Rigid Bodies

A slender uniform rod 100.00 cm long is used as a meter stick. Two parallel axes that are perpendicular to the rod are considered. The first axis passes through the 50-cm mark and the second axis passes through the 30-cm mark. What is the ratio of the moment of inertia through the second axis to the moment of inertia through the first axis?

A piece of thin uniform wire of mass m and length 3b is bent into an equilateral triangle. Find the moment of inertia of the wire triangle about an axis perpendicular to the plane of the triangle and passing through one of its vertices.

An extremely light rod 1.00 m long has a 2.00-kg mass attached to one end and a 3.00-kg mass attached to the other. The system rotates at a constant angular speed about a fixed axis perpendicular to the rod that passes through the rod 30.0 cm from the end with the 3.00-kg mass attached. The kinetic energy of the system is measured to be 100.0 J. (a) What is the moment of inertia of this system about the fixed axis? (b) What is the angular speed (in revolutions per second) of this system?

A 4.50-kg wheel that is 34.5 cm in diameter rotates through an angle of 13.8 rad as it slows down uniformly from 22.0 rad/s to 13.5 rad/s. What is the magnitude of the angular acceleration of the wheel?

At any angular speed, a certain uniform solid sphere of diameter D has half as much rotational kinetic energy as a certain uniform thin-walled hollow sphere of the same diameter when both are spinning about an axis through their centers. If the mass of the solid sphere is M, the mass of the hollow sphere is

A futuristic design for a car is to have a large solid disk-shaped flywheel within the car storing kinetic energy. The uniform flywheel has mass 370 kg with a radius of 0.500 m and can rotate up to 230 rev/s. Assuming all of this stored kinetic energy could be transferred to the linear velocity of the 1600-kg car, find the maximum attainable speed of the car.

A machinist turns the power on to a grinding wheel, which is at rest at time t = 0.00 s. The wheel accelerates uniformly for 10 s and reaches the operating angular velocity of 25 rad/s. The wheel is run at that angular velocity for 37 s and then power is shut off. The wheel decelerates uniformly at 1.5 rad/s² until the wheel stops. In this situation, the time interval of angular deceleration (slowing down) is closest to:

A uniform solid sphere of mass M and radius R rotates with an angular speed ω about an axis through its center. A uniform solid cylinder of mass M, radius R, and length 2R rotates through an axis running through the central axis of the cylinder. What must be the angular speed of the cylinder so it will have the same rotational kinetic energy as the sphere?

A horizontal disk rotates about a vertical axis through its center. Point P is midway between the center and the rim of the disk, and point Q is on the rim. If the disk turns with constant angular velocity, which of the following statements about it are true? (There may be more than one correct choice.)

In the figure, point P is at rest when it is on the x-axis. The linear speed of point P when it reaches the y-axis is closest to

As you are leaving a building, the door opens outward. If the hinges on the door are on your right, what is the direction of the angular velocity of the door as you open it?

The angular acceleration of a wheel is given in rad/s² by 45t³ - 11t⁴ where t is in seconds. If the wheel starts from rest at t = 0.00 s, when is the next time the wheel is at rest?

A dumbbell-shaped object is composed by two equal masses, m, connected by a rod of negligible mass and length r. If I₁ is the moment of inertia of this object with respect to an axis passing through the center of the rod and perpendicular to it and I₂ is the moment of inertia with respect to an axis passing through one of the masses, it follows that

A turbine blade rotates with angular velocity ω(t) = 2.00 rad/s- 2.1.00 rad/s3 t². What is the angular acceleration of the blade at t = 9.1 s?

A 3.45-kg centrifuge takes 100 s to spin up from rest to its final angular speed with constant angular acceleration. A point located 8.00 cm from the axis of rotation of the centrifuge moves with a speed of 150 m/s when the centrifuge is at full speed. (a) What is the angular acceleration (in rad/s²) of the centrifuge as it spins up? (b) How many revolutions does the centrifuge make as it goes from rest to its final angular speed?

When a 2.75-kg fan, having blades 18.5 cm long, is turned off, its angular speed decreases uniformly from 10.0 rad/s to 6.30 rad/s in 5.00 s. (a) What is the magnitude of the angular acceleration of the fan? (b) Through what angle (in degrees) does it turn while it is slowing down during the 5.00 s? (c) If its angular acceleration does not change, how long after it is turned off does it take the fan to stop.

A 1.15-kg grinding wheel 22.0 cm in diameter is spinning counterclockwise at a rate of 20.0 revolutions per second. When the power to the grinder is turned off, the grinding wheel slows with constant angular acceleration and takes 80.0 s to come to a rest. (a) What was the angular acceleration (in rad/s²) of the grinding wheel as it came to rest if we take a counterclockwise rotation as positive? (b) How many revolutions did the wheel make during the time it was coming to rest?

In the figure, point P is at rest when it is on the x-axis. The time t, when P returns to the original position on the x-axis, is closest to

A 1.25-kg ball begins rolling from rest with constant angular acceleration down a hill. If it takes 3.60 s for it to make the first complete revolution, how long will it take to make the next complete revolution?

While spinning down from 500.0 rpm to rest, a solid uniform flywheel does 5.1 kJ of work. If the radius of the disk is 1.2 m, what is its mass?